Additive-Manufactured Organic Interposers

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
A. Roshanghias ◽  
M. Krivec ◽  
J. Bardong ◽  
A. Binder
Keyword(s):  
Flip Chip ◽  
Three Dimensional ◽  
Heterogeneous Integration ◽  
3D Printer ◽  
3D Integration ◽  
Wire Bond ◽  
3D Printers ◽  
Additional Costs ◽  
3D Printed ◽  
Flexible Die

Abstract The trend toward heterogeneous integration of optoelectronic, electronic, and micromechanical components favors three-dimensional (3D) integration in which the components are not arranged side-by-side but rather in vertical stacks. This presents a particular challenge due to the fact that the stacked components have different geometric dimensions, and their contact surfaces are also dissimilar. Therefore, an intermediate substrate, the so-called interposer, with different formats (i.e., flip-chip, wire-bond, and hybrid flip-chip/wire bond) comes into play. Currently, the interposers are mainly made of silicon or glass, which incur huge additional costs to the packaged components. In this study, the unique advantages of additive manufacturing (AM) are exploited to realize organic interposers. The proposed interposers provide easy signal probing and flexible die-to-board integration in lower costs without any lithography process, drilling, plating, or any waste. Accordingly, the two state-of-the-art 3D printers (i.e., a monomaterial 3D printer and a bimaterial 3D printer) were utilized for the manufacturing of the interposer parts. The complementary circuitry for vias and through-holes was facilitated by also additive technologies, i.e., 2D-inkjet printing and microdispensing. Moreover, and to manifest the unique possibilities within AM for the next generation of interposers, two examples for 3D-printed interposers with incorporated added-features, i.e., pillars for flip-chip bonding and cavities for face-up die-attachment were realized. The assemblies were consequently assessed by electrical examinations. Conclusively, the main opportunities and challenges toward the full implementation of AM technology for the fabrication of organic interposers with added-features such as integrated multipurpose vias were discussed. Based on the results obtained from this study, it was found that bimaterial 3D printer was more efficient and powerful for the construction of interposers.

scholarly journals Implementing a 3D printing service in a biomedical library

2017 ◽  
Vol 105 (1) ◽  
Author(s):  
Verma Walker, MLIS
Keyword(s):  
Problem Solving ◽  
3D Printing ◽  
3D Modeling ◽  
Three Dimensional ◽  
National Institutes Of Health ◽  
3D Printer ◽  
Service Model ◽  
Steep Learning Curve ◽  
3D Printers ◽  
Creative Problem

Three-dimensional (3D) printing is opening new opportunities in biomedicine by enabling creative problem solving, faster prototyping of ideas, advances in tissue engineering, and customized patient solutions. The National Institutes of Health (NIH) Library purchased a Makerbot Replicator 2 3D printer to give scientists a chance to try out this technology. To launch the service, the library offered training, conducted a survey on service model preferences, and tracked usage and class attendance. 3D printing was very popular, with new lab equipment prototypes being the most common model type. Most survey respondents indicated they would use the service again and be willing to pay for models. There was high interest in training for 3D modeling, which has a steep learning curve. 3D printers also require significant care and repairs. NIH scientists are using 3D printing to improve their research, and it is opening new avenues for problem solving in labs. Several scientists found the 3D printer so helpful they bought one for their labs. Having a printer in a central and open location like a library can help scientists, doctors, and students learn how to use this technology in their work.

Aerosol Jet® Printer as an Alternative to Wire Bond and TSV Technology for 3D Interconnect Applications

2011 ◽  
Vol 2011 (1) ◽  
pp. 001028-001032
Author(s):  
Michael J. O’Reilly ◽  
Jeff Leal ◽  
Suzette K. Pangrle ◽  
Kenneth Vartanian
Keyword(s):  
Integrated Circuits ◽  
High Performance ◽  
Three Dimensional ◽  
Contact Printing ◽  
Wire Bond ◽  
Printing System ◽  
3D Printed ◽  
Working Distance ◽  
Aerosol Jet Deposition ◽  
Vertical Interconnect

Aerosol Jet deposition systems provide an evolutionary alternative to both wire bond and TSV technology. As part of the Vertical Interconnect Pillar (ViP™) process, the Aerosol Jet system prints high density three-dimensional (3D) interconnects enabling multi-function integrated circuits to be stacked and vertically interconnected in high performance System-in-Packages (SiP). The stacks can include two or more die, with a total height of ∼ 2 millimeters. The non-contact printing system has a working distance of several millimeters above the substrate allowing 3D interconnects to be printed with no Z-height adjustments. The Aerosol Jet printhead is configured with multiple nozzles and a closely coupled atomizer to achieve production throughput of greater than 19,000 interconnects per hour. The Aerosol Jet printer deposits silver fine particle ink to form connections on staggered die stacks. High aspect ratio interconnects, less than 30-microns wide and greater than 6-microns tall, are printed at sub 60-micron pitch. After isothermal sintering at 150° C to 200° C for 30 minutes, highly conductive interconnects near bulk resistivity are produced. Pre-production yields exceeding 80% have been realized. This paper will provide further details on the 3D printed interconnect process, current and planned production throughput levels, and process yield and device reliability status.

scholarly journals Flexible 3D Printed Molds for Educational Use. Digital Fabrication of 3D Typography

2019 ◽  
Vol 15 (13) ◽  
pp. 4 ◽  
Author(s):  
Alejandro Bonnet De León ◽  
Jose Luis Saorin ◽  
Jorge De la Torre-Cantero ◽  
Cecile Meier ◽  
María Cabrera-Pardo
Keyword(s):  
3D Modeling ◽  
Low Cost ◽  
Digital Fabrication ◽  
3D Printer ◽  
School Environments ◽  
Flexible Material ◽  
Educational Environments ◽  
3D Printers ◽  
3D Printed ◽  
The Subject

<p class="0abstract"><span lang="EN-US">One of the drawbacks of using 3D printers in educational environments is that the creation time of each piece is high and therefore it is difficult to manufacture at least one piece for each student. This aspect is important so that each student can feel part of the manufacturing process. To achieve this, 3D printers can be used, not to make pieces, but to make the molds that students use to create replicas. On the other hand, for a mold to be used to make several pieces, it is convenient to make it with flexible material. However, most used material for 3D printers (PLA) is very rigid. To solve this problem, this article designs a methodology that allows the use of low-cost 3D printers (most common in school environments) with flexible material so that each mold can be used to manufacture parts for several students. To print flexible material with low-cost printers, it is necessary to adapt the machine and the print parameters to work properly. This article analyzes the changes to be made with a low cost 3D printer and validates the use of molds in school environments. A pilot test has been carried out with 8 students of the subject of Typography, in the School of Art and Superior of Design of Tenerife. During the activity, the students carried out the process of designing a typography and creating digital molds for 3D printing with flexible material. The designs were made using free 3D modeling programs and low-cost technologies.</span></p>

scholarly journals Typography-Like 3D-Printed Templates for the Lithography-Free Fabrication of Microfluidic Chips

2019 ◽  
Vol 25 (1) ◽  
pp. 82-87
Author(s):  
Wenqiong Su ◽  
Yulong Li ◽  
Lulu Zhang ◽  
Jiahui Sun ◽  
Shuopeng Liu ◽  
...  
Keyword(s):  
Processing Time ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Cost Effective ◽  
Microfluidic Channels ◽  
3D Printer ◽  
Microfluidic Chips ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Typography-like templates for polydimethylsiloxane (PDMS) microfluidic chips using a fused deposition modeling (FDM) three-dimensional (3D) printer are presented. This rapid and fast proposed scheme did not require complicated photolithographic fabrication facilities and could deliver resolutions of ~100 μm. Polylactic acid (PLA) was adopted as the material to generate the 3D-printed units, which were then carefully assembled on a glass substrate using a heat-melt-curd strategy. This craft of bonding offers a cost-effective way to design and modify the templates of microfluidic channels, thus reducing the processing time of microfluidic chips. Finally, a flexible microfluidic chip to be employed for cell-based drug screening was developed based on the modularized 3D-printed templates. The lithography-free, typography-like, 3D-printed templates create a modularized fabrication process and promote the prevalence of integrated microfluidic systems with minimal requirements and improved efficiency.

scholarly journals Three-dimensional Printing Versus Conventional Machining in the Creation of a Meatal Urethral Dilator: a Cost and Mechanical Strength Analysis

2020 ◽  
Author(s):  
Michael Yue-Cheng Chen ◽  
Jacob Skewes ◽  
Ryan Daley ◽  
Maria Ann Woodruff ◽  
Nicholas John Rukin
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Patient Specific ◽  
Strength Analysis ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Current Time ◽  
Fused Deposition ◽  
3D Printed ◽  
Conventional Machining

Abstract BackgroundThree-dimensional (3D) printing is a promising technology but the limitations are often poorly understood. We compare different 3D printingmethods with conventional machining techniques in manufacturing meatal urethral dilators which were recently removed from the Australian market. MethodsA prototype dilator was 3D printed vertically orientated on a low cost fused deposition modelling (FDM) 3D printer in polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS). It was also 3D printed horizontally orientated in ABS on a high-end FDM 3D printer with soluble support material, as well as on a SLS 3D printer in medical nylon. The dilator was also machined in stainless steel using a lathe. All dilators were tested mechanically in a custom rig by hanging calibrated weights from the handle until the dilator snapped. ResultsThe horizontally printed ABS dilator experienced failure at a greater load than the vertically printed PLA and ABS dilators respectively (503g vs 283g vs 163g, p < 0.001). The SLS nylon dilator and machined steel dilator did not fail. The steel dilator is most expensive with a quantity of five at 98 USD each, but this decreases to 30 USD each for a quantity of 1000. In contrast, the cost for the SLS dilator is 33 USD each for five and 27 USD each for 1000. ConclusionsAt the current time 3D printing is not a replacement for conventional manufacturing. 3D printing is best used for patient-specific parts, prototyping or manufacturing complex parts that have additional functionality that cannot otherwise beachieved.

Using 3D Printers to Engage Students in Research

2019 ◽  
pp. 50-69
Author(s):  
Jim Flowers
Keyword(s):  
Additive Manufacturing ◽  
Research And Development ◽  
Educational Experiences ◽  
Physical And Mechanical Properties ◽  
Testing Equipment ◽  
3D Printer ◽  
3D Printers ◽  
3D Printed ◽  
Manufacturing Technologies ◽  
Student Inquiry

Is the primary purpose of a 3D printer to manufacture a product? Yes, but students and teachers can also use 3D printers to learn about and engage in research and experimentation. This could begin with product research and development, then expand to technical areas based on additive manufacturing technologies, the physical and mechanical properties of additive manufacturing materials, and the properties of 3D printed products. Student inquiry can take the form of formal or informal experimentation and observational studies. Although dedicated testing equipment can facilitate more demanding investigations, it is possible for quite a bit of experimentation to be done with little or no dedicated testing equipment. It is hoped that the reader will identify different educational experiences with experimentation that might fit their learners' needs and see 3D printers as tools for conducting and teaching about research, including product research and development and research into process engineering and materials.

scholarly journals Orthopedics and 3D technology in Turkey: A preliminary report

2021 ◽  
Vol 32 (2) ◽  
pp. 279-289
Author(s):  
Cemil Ertürk ◽  
Simel Ayyıldız ◽  
Cevdet Erdöl
Keyword(s):  
Surgical Simulation ◽  
Three Dimensional ◽  
Radiographic Examination ◽  
Acetabular Bone Defect ◽  
Custom Made ◽  
Revision Tha ◽  
3D Printers ◽  
3D Printed ◽  
Acetabular Defects ◽  
Pilon Fractures

Objectives: In this study, we present the use of case specific three- dimensional (3D) printed plastic models and custom-made acetabular implants in orthopedic surgery. Materials and methods: Between March 2018 and September 2020, surgeries were simulated using plastic models manufactured by 3D printers on the two patients with pilon fractures. Also, custom-made acetabular implants were used on two patients with an acetabular bone defect for the revision of total hip arthroplasty (THA). Results: More comfortable surgeries were experienced in pilon fractures using preoperative plastic models. Similarly, during the follow-up period, the patients that applied custom-made acetabular implants showed a fixed and well-positioning in radiographic examination. These patients did not experience any surgical complications and achieved an excellent recovery. Conclusion: Preoperative surgical simulation with 3D printed models can increase the comfort of fracture surgeries. Also, custom-made 3D printed acetabular implants can perform an important task in patients treated with revision THA surgery due to severe acetabular defects.

scholarly journals A LITHOPHANE MODEL MAKING PROCESS TO 3D PRINTERS

2020 ◽  
Author(s):  
Siddavatam Rammohan Reddy
Keyword(s):  
Melting Point ◽  
Acrylonitrile Butadiene Styrene ◽  
3D Models ◽  
3D Printer ◽  
Layer By Layer ◽  
3 Dimensional ◽  
3D Objects ◽  
3D Printers ◽  
3D Printed ◽  
Butadiene Styrene

This paper focuses on to convert photographs into embossed 3D models and then bring them to life using a 3D printer. A Lithophane is a 3-dimensional generation of a 2-dimensional image and 3D representation of a photo can be seen only when it is illuminated from behind. Turning images into 3D objects give us more feeling and literally adds a new dimension. The lithophane can be manufactured by the way of an automated additive manufacturing process, such as 3-D printing. lithophanes are a simple way to enhance your favourite photos. 3D printed photos also known as 3D Printed lithophanes, are an extremely unique and creative application. The process adopted in lithophane is FDM technology, in which different the materials like PLA (polylactic acid), ABS (acrylonitrile butadiene styrene), etc. By heating the filament material to its melting point and it is deposited layer by layer. Combination of many layers will give us a final 3D Printed model.

scholarly journals Dimensional Stability of 3D Printed Objects Made from Plastic Waste Using FDM: Potential Construction Applications

Buildings ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 516
Author(s):  
Essam Zaneldin ◽  
Waleed Ahmed ◽  
Aya Mansour ◽  
Amged El Hassan
Keyword(s):  
3D Printing ◽  
Construction Projects ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Cost Effective ◽  
Plastic Waste ◽  
Fused Deposition ◽  
Feasible Option ◽  
3D Printers ◽  
3D Printed

Construction projects are often challenged by tight budgets and limited time and resources. Contractors are, therefore, looking for ways to become competitive by improving efficiency and using cost-effective materials. Using three-dimensional (3D) printing for shaping materials to produce cost-effective construction elements is becoming a feasible option to make contractors more competitive locally and globally. The process capabilities for 3D printers and related devices have been tightened in recent years with the booming of 3D printing industries and applications. Contractors are attempting to improve production skills to satisfy firm specifications and standards, while attempting to have costs within competitive ranges. The aim of this research is to investigate and test the production process capability (Cp) of 3D printers using fused deposition modeling (FDM) to manufacture 3D printed parts made from plastic waste for use in the construction of buildings with different infill structures and internal designs to reduce cost. This was accomplished by calculating the actual requirement capabilities of the 3D printers under consideration. The production capabilities and requirements of FDM printers are first examined to develop instructions and assumptions to assist in deciphering the characteristics of the 3D printers that will be used. Possible applications in construction are then presented. As an essential outcome of this study, it was noticed that the 3D printed parts made from plastic waste using FDM printers are less expensive than using traditional lightweight non-load bearing concrete hollow masonry blocks, hourdi slab hollow bocks, and concrete face bricks.

scholarly journals Properties of 3D-printed wood sawdust-reinforced PLA composites

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5467-5480
Author(s):  
Nasir Narlıoğlu ◽  
Tufan Salan ◽  
Mehmet Hakkı Alma
Keyword(s):  
Mechanical Properties ◽  
Mechanical Test ◽  
Three Dimensional ◽  
Value Added ◽  
Polymeric Materials ◽  
Mechanical Tests ◽  
3D Printer ◽  
Pine Sawdust ◽  
Wood Sawdust ◽  
3D Printed

Thermal, morphological, and mechanical properties of three-dimensional (3D) printed polylactic acid (PLA) composites reinforced with different amounts of waste pine sawdust were investigated. To determine the mechanical properties of the obtained filaments, test samples were produced using a 3D printer according to the mechanical test standards. The filaments that were produced from blends that contained the wood sawdust at the highest level (20%) could be printed via a 3D printer without any problems. According to the results obtained from the mechanical tests, a decrease in the tensile strength values of the composites was observed with the addition of wood sawdust into the neat PLA polymer. On the other hand, it was determined that the flexural strength values of the wood sawdust/PLA composites significantly increased with the addition of the wood sawdust. It was concluded that the waste pine sawdust is a reasonable reinforcement material for the production of composite filament for 3D printing applications and it can be compatibly extruded with PLA polymer. Thus, sawdust can be used as a value-added waste source for the production of high-quality 3D polymeric materials.

Sign in / Sign up

Export Citation Format

Share Document