Effect of Biogas Composition Variations on Engine Characteristics Including Operational Limits of a Spark-Ignition Engine

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Sachin Kumar Gupta ◽  
Mayank Mittal
Keyword(s):  
Carbon Dioxide ◽  
Thermal Efficiency ◽  
Carbon Dioxide Emissions ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Si Engine ◽  
Promising Alternative ◽  
Brake Thermal Efficiency ◽  
Indicated Mean Effective Pressure ◽  
Wide Range

Biogas is a promising alternative fuel to reduce the consumption of petroleum-based fuels in internal combustion (IC) engines. In this work, the effect of various biogas compositions on the performance, combustion, and emission characteristics of a spark-ignition (SI) engine is investigated. Additionally, the effect of Wobbe index (WI) of various fuel compositions was also evaluated on the operational limits of the engine. While considering a wide range of biogas compositions (including bio-methane), the percentage of carbon dioxide (CO2) (in a blend of methane and CO2) was increased from 0 to 50% (by volume). A single-cylinder, water-cooled, SI engine was operated at 1500 rpm over a wide range of operating loads with compression ratio of 8.5:1. With the increase in WI of the fuel, both low (limited by coefficient of variation (COV) of indicated mean effective pressure (IMEP)) and high (limited by pre-ignition) operating loads were decreased; however, it was found that the overall operating range was increased. Results also showed that for a given operating load, with the increase of CO2 percentage in the fuel, the brake thermal efficiency was decreased, and the flame initiation and combustion durations were increased. The brake thermal efficiency was decreased from 16.8% to 13.7%, when CO2 was increased from 0% to 40% in methane–CO2 mixture at 8 N·m load. Concerning to emissions, a considerable decrease was noted in nitric oxide, whereas hydrocarbon, carbon monoxide and carbon dioxide emissions were increased, with the increase in CO2 percentage.

Assessing the Influence of Compression Ratio on Engine Characteristics Including Operational Limits of a Biogas-Fueled Spark-Ignition Engine

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Sachin Kumar Gupta ◽  
Mayank Mittal
Keyword(s):  
Compression Ratio ◽  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Operating Range ◽  
Indicated Mean Effective Pressure ◽  
Wide Range

Abstract Biogas, which is a renewable alternative fuel, has high antiknocking properties with the potential to substitute fossil fuels in internal combustion engines. In this study, performance characteristics of a spark-ignition (SI) engine operated under methane (baseline case) and biogas are compared at the compression ratio (CR) of 8.5:1. Subsequently, the effect of CR on operational limits, performance, combustion, and emission characteristics of the engine fueled with biogas is evaluated. A variable compression ratio, spark-ignition engine was operated at various CRs of 8.5:1, 10:1, 11:1, 13:1, and 15:1 over a wide range of operating loads at 1500 rpm. Results showed that the operating range of the engine at 8.5:1 CR reduced when biogas was utilized in the engine instead of methane. However, the operating range of the engine for biogas extended with an increase in CR—an increase from 9.6 N-m-16.5 N-m to 2.8 N-m-15.1 N-m was observed when CR was increased from 8.5:1 to 15:1. The brake thermal efficiency improved from 13.7% to 16.3%, and the coefficient of variation (COV) of indicated mean effective pressure (IMEP) reduced from 12.7% to 1.52% when CR was increased from 8.5:1 to 15:1 at 8 N-m load. The emission level of carbon dioxide was decreased with an increase in CR due to an improvement in the thermal efficiency and the combustion process.

scholarly journals An Attempt to Reduce the Emission of Spark-Ignition Engine with Mixtures of Bioethanol and Gasoline as Substitute Fuels

2019 ◽  
Vol 26 (3) ◽  
pp. 31-38
Author(s):  
Wojciech Gis ◽  
Maciej Gis ◽  
Piotr Wiśniowski ◽  
Mateusz Bednarski
Keyword(s):  
Carbon Dioxide ◽  
Fuel Consumption ◽  
Carbon Dioxide Emissions ◽  
Alternative Fuels ◽  
Negative Impact ◽  
Spark Ignition ◽  
Solid Particles ◽  
Spark Ignition Engine ◽  
Maximum Power ◽  
The Impact

Abstract Limiting emissions of harmful substances is a key task for vehicle manufacturers. Excessive emissions have a negative impact not only on the environment, but also on human life. A significant problem is the emission of nitrogen oxides as well as solid particles, in particular those up to a diameter of 2.5 microns. Carbon dioxide emissions are also a problem. Therefore, work is underway on the use of alternative fuels to power the vehicle engines. The importance of alternative fuels applies to spark ignition engines. The authors of the article have done simulation tests of the Renault K4M 1.6 16v traction engine for emissions for fuels with a volumetric concentration of bioethanol from 10 to 85 percent. The analysis was carried out for mixtures as substitute fuels – without doing any structural changes in the engine's crankshafts. Emission of carbon monoxide, carbon dioxide, hydrocarbons, oxygen at full throttle for selected rotational speeds as well as selected engine performance parameters such as maximum power, torque, hourly and unit fuel consumption were determined. On the basis of the simulation tests performed, the reasonableness of using the tested alternative fuels was determined on the example of the drive unit without affecting its constructions, in terms of e.g. issue. Maximum power, torque, and fuel consumption have also been examined and compared. Thus, the impact of alternative fuels will be determined not only in terms of emissions, but also in terms of impact on the parameters of the power unit.

scholarly journals Experimental investigation on combustion, performance, and emissions characteristics of butanol as an oxygenate in a spark ignition engine

2017 ◽  
Vol 9 (2) ◽  
pp. 168781401668884 ◽  
Author(s):  
Yu Li ◽  
Jinke Gong ◽  
Wenhua Yuan ◽  
Jun Fu ◽  
Bin Zhang ◽  
...  
Keyword(s):  
Carbon Monoxide ◽  
Nitrogen Oxides ◽  
Thermal Efficiency ◽  
Alternative Fuel ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Combustion Performance ◽  
Performance And Emissions ◽  
Unburned Hydrocarbons

Ethanol is known as the most widely used alternative fuel for spark-ignition engines. Compared to it, butanol has proved to be a very promising renewable fuel in recent years for desirable properties. The conjoint analysis on combustion, performance, and emissions characteristics of a port fuel injection spark-ignition engine fueled with butanol–gasoline blends was carried out. In comparison with butanol–gasoline blends with various butanol ratio (0–60 vol% referred as G100~B60) and conventional alcohol alternative fuels (methanol, ethanol, and butanol)–gasoline blends, it shows that B30 performs well in engine performance and emissions, including brake thermal efficiency, brake-specific fuel consumption, carbon monoxide, unburned hydrocarbons, and nitrogen oxides. Then, B30 was compared with G100 under various equivalence ratios ( Φ = 0.83–1.25) and engine loads (3 and 5-bar brake mean effective pressure). In summary, B30 presents an advanced combustion phasing, which leads to a 0.3%–2.8% lower brake thermal efficiency than G100 as the engine was running at the spark timing of gasoline’s maximum brake torque (MBT). Therefore, the sparking timing should be postponed when fueled with butanol–gasoline blends. For emissions, the lower carbon monoxide (2.3%–8.7%), unburned hydrocarbons (12.4%–27.5%), and nitrogen oxides (2.8%–19.6%) were shown for B30 compared with G100. Therefore, butanol could be a good alternative fuel to gasoline for its potential to improve combustion efficiency and reduce pollutant emissions.

scholarly journals Influence of Compression Ratio on Flywheel Dimension for a Naturally Aspirated Spark Ignition Engine: A Numerical Study

2020 ◽  
Vol 3 (2) ◽  
Author(s):  
Aan Yudianto ◽  
Peixuan Li
Keyword(s):  
Compression Ratio ◽  
Numerical Study ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Effective Pressure ◽  
Si Engine ◽  
Compression Stroke ◽  
Indicated Mean Effective Pressure ◽  
Proper Design

The proper design of the flywheel undeniably determines in tuning the engine to confirm the better output engine performance. The aim of this study is to mathematically investigate the effect of various values of the compression ratio on some essential parameters to determine the appropriate value for the flywheel dimension. A numerical calculation approach was proposed to eventually determine the dimension of the engine flywheel on a five-cylinder four-stroke Spark Ignition (SI) engine. The various compression ratios of 8.5, 9, 9.5, 10, 10.5, and 11 were selected to perform the calculations. The effects of compression ratio on effective pressure, indicated mean effective pressure (IMEP), dynamic irregularity value of the crankshaft, and the diameter of the flywheel was clearly investigated. The study found that 2.5 increment value of the compression ratio significantly increases the effective pressure of about 41.53% on the starting of the expansion stroke. While at the end of the compression stroke, the rise of effective pressure is about 76.67%, and the changes in dynamic irregularity merely increase by about 1.79%. The same trend applies to the flywheel diameter and width, which increases 2.08% for both.

scholarly journals INVESTIGATION OF MULTI-ZONE MODELS FOR SPARK IGNITION ENGINE FUELED WITH ETHANOL

2021 ◽  
Vol 22 (2) ◽  
pp. 339-351
Author(s):  
A. A. Dare ◽  
Olanrewaju Olatunde ◽  
O. S. Ismail ◽  
A. S. Shote ◽  
O. J. Alamu ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Ignition Time ◽  
High Volume ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Zone Model ◽  
Fuel Blends ◽  
Indicated Mean Effective Pressure ◽  
First Case

This research is aimed at investigating the effect of using ethanol (E100) in multi-zone model analysis consisting of multi-combustion chamber zoning cases. The first case considered is a three-zone model that has an unburned zone, burned zone, and transitory zone. The second case model is also three-zone, consisting of an unburned zone and two partitioned burned zones. The burned zone was imagined partitioned into burned zone-1 and burned zone-2 under uneven fuel distribution having different equivalent ratios. The third case is a four-zone model including two regions of burned zone, an unburned zone and a transitory zone, which is unburned burned zone containing a mixture of unburned and burned gases. Arbitrary constants for each of the unburned (CC1) and burned (CC2) Zone leakages in the unburned burned Zone are 0.00025, 0.0005, 0.001, 0.002, 0.005, 0.1 and 0.5. The Mass Fraction Burned (MFB) for zone-1, x1 and burned zone-2, x2 are computed using Partitioned Burnt Zones Ratios (PBZR) of 2:8, 3:7, 4:6, 5:5, 6:4, 7:3 and 8:2. Two equivalent ratios, one for each fuel MFB (?1, ?2), (0.8, 0.6) and (0.6, 0.8) are analyzed using fuel blends of varying percentage. A comparison of values of the three zoning cases is done using peak values from the three-zone models to evaluate the four-zone model. The model was compared with a spark ignition engine (SIE) operating with a premium motor spirit (PMS) serving as baseline. The engine operating conditions were set at an engine speed of 2000 rpm, -35bTDC ignition time, and burn duration at 60 oC. The indicated mean effective pressure (IMEP), thermal efficiency (?), cylinder pressure and emission fraction from the developed models and those of two-zone analysis obtained agreed with literature values. The result showed it is undesirable to have a high volume of burned charge as infiltrate. The three-zone segmented model predicted the highest engine thermal efficiency and peak pressure at mass burn ratio of 7:3. A general reduction in N2 emission was observed for the three-zone transitional and four-zone models. ABSTRAK: Kajian ini menilai kesan etanol (E100) dalam analisis model zon-berbilang yang terdapat pada masalah pengezonan kebuk pembakaran-berbilang. Kes pertama yang diambil kira adalah model tiga-zon yang mempunyai zon tidak terbakar, zon terbakar dan zon peralihan. Model kedua merupakan juga tiga-zon yang terdiri daripada zon tidak-terbakar dan dua zon bahagian yang terbakar. Zon yang terbakar dibahagikan kepada zon-1 terbakar dan zon-2 terbakar di bawah kebakaran tidak sekata yang mempunyai nisbah berlainan. Kes ketiga adalah model zon-keempat termasuk dua kawasan zon terbakar, zon tidak-terbakar dan zon peralihan iaitu zon terbakar tidak-terbakar di mana ia adalah campuran gas terbakar dan tidak-terbakar. Tetapan sebarangan bagi setiap zon kebocoran tidak-terbakar (CC1) dan terbakar (CC2) dalam zon terbakar tidak-terbakar adalah 0.00025, 0.0005, 0.001, 0.002, 0.005, 0.1 dan 0.5. Pecahan Jisim Terbakar (MFB) bagi zon-1, x1 dan zon-2 terbakar, x2 dikira menggunakan Nisbah Zon Bahagian Terbakar (PBZR) sebanyak 2:8, 3:7, 4:6, 5:5, 6:4, 7:3 dan 8:2. Nisbah dua persamaan, setiap satu bahan api MFB adalah (?1, ?2), (0.8, 0.6) dan (0.6, 0.8) dan diuji menggunakan pelbagai peratus bahan api campuran. Nilai perbandingan bagi tiga kes zon dibuat menggunakan nilai puncak dari model tiga-zon bagi menilai model empat-zon. Model ini dibandingkan dengan enjin cucuhan bunga api (SIE) beroperasi dengan motor alkohol premium (PMS) sebagai garis asas. Keadaan operasi enjin adalah dihadkan pada 2000 rpm kelajuan enjin, masa pencucuhan -35bTDC dan tempoh pembakaran pada 60 oC. Tekanan berkesan min tertunjuk (IMEP), kecekapan haba tertunjuk (?), tekanan silinder dan pecahan pengeluaran dari model yang dibangunkan dan analisis dua-zon yang terhasil adalah sama dengan nilai literatur. Dapatan kajian menunjukkan cas terbakar pada isipadu yang banyak adalah tidak diingini sebagai penyerap. Model tiga bahagian zon menunjukkan kecekapan haba enjin tertinggi dan tekanan puncak pada jisim bakar dengan nisbah 7:3. Manakala, pengurangan umum telah diperhatikan pada pengeluaran N2 di peralihan tiga-zon dan model empat zon.

Thermodynamic analysis of using ethanol-methanol-gasoline (GEM) blends in a turbocharged, spark-ignition engine

2021 ◽  
pp. 1-28
Author(s):  
Hongqing Feng ◽  
Shuwen Xiao ◽  
Zhirong Nan ◽  
Di Wang ◽  
Chaohe Yang
Keyword(s):  
Thermal Efficiency ◽  
Fossil Fuel ◽  
Spark Ignition ◽  
Exergy Efficiency ◽  
Spark Ignition Engine ◽  
Low Carbon ◽  
Si Engine ◽  
Engine Load ◽  
Maximum Value ◽  
Spark Timing

Abstract Low-carbon alcohols have been universally acknowledged as an alternative to fossil fuel in the world, which is environmentally friendly and clean. In this paper, the detailed exergy and energy analysis were carried out on a turbocharged, spark-ignition (SI) engine fueled with methanol-ethanol-gasoline (GEM) under non-knock conditions. The results indicated that increasing the alcohols proportion in blends could slightly improve the exergy efficiency and thermal efficiency and increase the percentage of total irreversibility in the total exergy. The thermal efficiency and exergy efficiency increased to a maximum value and then decreased, while the proportion of total irreversibility in the total exergy increased significantly with the spark timing retarded from the earliest timing. The exergy efficiency and thermal efficiency increased as the engine load increased. Additionally, the total irreversibility increased but the proportion of total irreversibility in the total exergy presented a trend of decreasing as the engine load increased.

scholarly journals The Operating Features of a Stoichiometric, Ammonia and Gasoline Dual Fueled Spark Ignition Engine

2006 ◽  
Author(s):  
Shawn M. Grannell ◽  
Dennis N. Assanis ◽  
Stanislav V. Bohac ◽  
Donald E. Gillespie
Keyword(s):  
Compression Ratio ◽  
Thermal Efficiency ◽  
Maximum Load ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Gaseous Ammonia ◽  
Spark Ignition Engines ◽  
Stoichiometric Mixture ◽  
Brake Thermal Efficiency ◽  
Practical Operation

An overall stoichiometric mixture of air, gaseous ammonia and gasoline was metered into a single cylinder, variable compression ratio, supercharged CFR engine at varying ratios of gasoline to ammonia. The engine was operated such that the combustion was knock-free with minimal roughness for all loads ranging from idle up to a maximum load in the supercharge regime. For a given load, speed, and compression ratio there was a range of ratios of gasoline to ammonia for which knock-free, smooth firing was obtained. This range was investigated at its roughness limit and also at its knock limit. If too much ammonia was used, then the engine fired with an excessive roughness. If too much gasoline was used, then knock-free combustion could not be obtained while the maximum brake torque spark advance was maintained. Stoichiometric operation on gasoline alone was also investigated, for comparison. It was found that a significant fraction of the gasoline used in spark ignition engines could be replaced with ammonia. Operation on mostly gasoline was required near idle. However, mostly ammonia could be used at high load. Operation on ammonia alone was possible at some of the supercharged load points. Generally, the use of ammonia or ammonia with gasoline allowed knock-free operation at higher compression ratios and higher loads than could be obtained with the use of gasoline alone. The use of ammonia/gasoline allowed practical operation at a compression ratio of 12:1 whereas the limit for gasoline alone was 9:1. When running on ammonia/gasoline the engine could be operated at brake mean effective pressures that were more than 50% higher than those achieved with the use of gasoline alone. The maximum brake thermal efficiency achieved with the use of ammonia/gasoline was 32.0% at 10:1 compression ratio and BMEP = 1025 kPa. The maximum brake thermal efficiency possible for gasoline was 24.6% at 9:1 and BMEP = 570 kPa.

An Investigation of the Effect of 2T Oil Blend on Spark Ignition Engine Performance

2014 ◽  
Vol 663 ◽  
pp. 289-293
Author(s):  
M. Nurhidayat Zahelem ◽  
A. Siti Rohana ◽  
N. Haniza B. Jemily ◽  
M. Amzari Aris ◽  
Shukri Zain ◽  
...  
Keyword(s):  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Si Engine ◽  
Brake Thermal Efficiency ◽  
Blend Ratio ◽  
Engine Torque ◽  
Synthetic Oil ◽  
Brake Mean Effective Pressure ◽  
Oil Blend

This paper presents the results of an investigation on the effect of 2T oil blend on the performance of Spark Ignition (SI) engine. Three different types of 2T-oils; mineral oil, semi-synthetic oil and fully synthetic oil were tested according to blend ratio before the mixing process with fuel in the carburetor. In the experiment, a two-stroke single-cylinder engine was coupled to a 20 kW generator dynamometer to measure engine performance parameters; engine torque, engine power (B.P), brake thermal efficiency (BTE), brake specific fuel consumption (BSFC) and brake mean effective pressure (BMEP) at various engine speeds with maximum engine load. The results show correlation between engine performances and 2T-oil blended as a function of type of 2T-oils used.

scholarly journals Effect of ignition timing on engine characteristics of a single cylinder spark ignition engine with CNG fueled

2017 ◽  
Vol 20 (K6) ◽  
pp. 79-86
Author(s):  
Quoc Dang Tran
Keyword(s):  
Natural Gas ◽  
Thermal Efficiency ◽  
Engine Speed ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Ignition Timing ◽  
Compressed Natural Gas ◽  
Brake Thermal Efficiency ◽  
Timing System ◽  
Cng Engine

This article shows an investigated research on Compressed Natural Gas (CNG) engine with a port injection when varying ignition timing. The obtained results from simulating study have indicated that both of brake thermal efficiency and torque have a similar trend when varying ignition timing. The effect of ignition timing on the value of brake thermal efficiency is stronger in comparison with torque, however, the increase in engine speed or lambda value have to adjust the ignition timing more early. To reach the maximum break torque at each engine speed, the ignition timing should be adjusted IT = 14 - 32 bTDC, and this is also basic value to design the ignition timing system using CNG engine with port injection.

Development of a natural gas spark ignition engine for optimum performance

1997 ◽  
Vol 211 (5) ◽  
pp. 361-378 ◽  
Author(s):  
A Das ◽  
H C Watson
Keyword(s):  
Natural Gas ◽  
Spark Ignition ◽  
Limited Range ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Petrol Engine ◽  
Shape Modification ◽  
Will Emit ◽  
Brake Thermal Efficiency ◽  
Wide Range

A 4 litre displacement, six cylinder, fuel injected petrol engine was modified to natural gas (NG) fuelling. Experimental investigation was carried out with various mixture controls and compression ratios over a wide range of operating conditions. As a strategy for combustion chamber shape modification, the compression ratio was raised with simultaneous enhancement of in-cylinder turbulence through squish motion. A fast burning chamber for the combustion of lean mixtures of natural gas and air was developed. Brake thermal efficiency in excess of 40 per cent and brake torque in excess of the peak base torque with petrol were achieved. The research provides the foundation for the implementation of NG cars that will emit only about 65 per cent of the carbon dioxide (CO2) of their petrol engine counterparts, with the prospect of extending the limited range of NG cars by up to one-third and producing low hydrocarbon (HC) and nitrogen oxide (NOx) emissions.

Sign in / Sign up

Export Citation Format

Share Document