Welding Residual Stress in HDPE Pipes: Measurement and Numerical Simulation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Yu Sun ◽  
Yun-Fei Jia ◽  
Muhammad Haroon ◽  
Huan-sheng Lai ◽  
Wenchun Jiang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Stress Distribution ◽  
Welded Joints ◽  
Residual Stress Distribution ◽  
Fusion Welding ◽  
Welding Residual Stress ◽  
Hole Drilling ◽  
Radial Depth ◽  
Hdpe Pipes

To understand the residual stress distribution in the welded joints of high density polyethylene (HDPE) pipes is essential to the assessment of its structural integrity. However, limited knowledge of their residual stress was available in this regard. In this paper, the hole-drilling strain-gage method was used to measure the residual stress in the welded seam of HDPE pipes, which was produced by the butt fusion welding technique. The finite element modeling using viscoelastic constitutive model with Prony series was carried out to determine the temperature field and corresponding stress field in the welding stages. The measured residual stress near the surface shows good consistency with the numerical results. It is shown that the residual stress in the hoop direction is much larger than those in the radial and axial directions. The effect of the pipe thickness on the residual stress distribution was also investigated by numerical simulation. The positions of the maximum tensile stress in the welded joints were found within the normalized depth region (the radial depth to the thickness) of 0.2 to 0.8.

Research on the Residual Stress of Aluminum Alloy (LF6) Welding

2013 ◽  
Vol 546 ◽  
pp. 127-131
Author(s):  
Zhi Qing Guo ◽  
Qiu Juan Lv ◽  
Yan Jiao Li ◽  
Chang Jiang Liu ◽  
Fang Xie
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Experimental Study ◽  
Aluminum Alloy ◽  
Stress Distribution ◽  
Residual Stress Distribution ◽  
Welding Residual Stress ◽  
Welding Seam ◽  
Maximum Value

This paper use the software ANSYS to study the aluminum alloy (LF6) welding residual stress by numerical simulation and experimental study. The result indicates that the aluminum alloy (LF6) has the same residual stress distribution with others, there is a maximum value existing at the range of 4-5mm near the welding seam.

scholarly journals Influence of Interlayer Temperature and Welding Sequence on the Temperature Distribution and Welding Residual Stress of the Saddle-Shaped Joint of Weldolet-Header Butt Welding

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 5980
Author(s):  
Chunliang Mai ◽  
Xue Hu ◽  
Lixin Zhang ◽  
Bao Song ◽  
Xiongfei Zheng
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Stress Distribution ◽  
High Stress ◽  
Welding Process ◽  
Residual Stress Distribution ◽  
Welding Residual Stress ◽  
Two Stage ◽  
Welding Sequence ◽  
Simulation Results

In this paper, based on Simufact Welding finite element analysis software, a numerical simulation of the temperature and residual stress distribution of the weldolet-header multi-layer multi-pass welding process is carried out, and the simulation results are verified through experiments. The experimental results are in good agreement with the numerical simulation results, which proves the validity of the numerical simulation results. Through the results of the numerical simulation, the influence of the welding sequence and interlayer temperature on the temperature and residual stress distribution at different locations of the saddle-shaped weld was studied. The results show that the temperature and residual stress distribution on the header and weldolet are asymmetric, and the high-stress area of the saddle-shaped welded joint always appears at the saddle shoulder or saddle belly position. When the interlayer temperature is 300 °C, the peak residual stress reaches a minimum of 428.35 MPa. Adjusting the welding sequence can change the distribution trend of residual stress. There is no high-stress area on the first welding side of the two-stage welding path-2. The peak values of residual stresses for continuous welding path-1 and two-stage welding path-2 are 428.35 MPa and 434.01 MPa, respectively, which are very close to each other.

Finite Element Analyses of Residual Stresses in Typical Welded Joints Used in Nuclear Power Plants and Comparisons With Experiments

2010 ◽  
Author(s):  
Dean Deng ◽  
Kazuo Ogawa ◽  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welded Joints ◽  
Nuclear Power ◽  
Power Plants ◽  
Butt Joint ◽  
Welding Residual Stress ◽  
Dissimilar Metal ◽  
Water Reactors

Recent discoveries of stress corrosion cracking (SCC) at nickel-based metals in pressurized water reactors (PWRs) and boiling water reactors (BWRs) have raised concerns about safety and integrity of plant components. It has been recognized that welding residual stress is an important factor causing the issue of SCC in a weldment. In this study, both numerical simulation technology and experimental method were employed to investigate the characteristics of welding residual stress distribution in several typical welded joints, which are used in nuclear power plants. These joints include a thick plate butt-welded Alloy 600 joint, a dissimilar metal J-groove set-in joint and a dissimilar metal girth-butt joint. First of all, numerical simulation technology was used to predict welding residual stresses in these three joints, and the influence of heat source model on welding residual stress was examined. Meanwhile, the influence of other thermal processes such as cladding, buttering and heat treatment on the final residual stresses in the dissimilar metal girth-butt joint was also clarified. Secondly, we also measured the residual stresses in three corresponding mock-ups. Finally, the comparisons of the simulation results and the measured data have shed light on how to effectively simulate welding residual stress in these typical joints.

Numerical simulation of the effect of ultrasonic impact treatment on welding residual stress

2021 ◽  
pp. 2150175
Author(s):  
Tao Mo ◽  
Jingqing Chen ◽  
Pengju Zhang ◽  
Wenqian Bai ◽  
Xiao Mu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Compressive Stress ◽  
Welded Joints ◽  
Welding Process ◽  
Residual Compressive Stress ◽  
Welding Residual Stress ◽  
304 Stainless Steel ◽  
Residual Tensile Stress ◽  
Ultrasonic Impact Treatment

Ultrasonic impact treatment (UIT) is an effective method that has been widely applied in welding structure to improve the fatigue properties of materials. It combines mechanical impact and ultrasonic vibration to produce plastic deformation on the weld joints surface, which introduces beneficial compressive residual stress distribution. To evaluate the effect of UIT technology on alleviating the residual stress of welded joints, a novel numerical analysis method based on the inherent strain theory is proposed to simulate the stress superposition of welding and subsequent UIT process of 304 stainless steel. Meanwhile, the experiment according to the process was carried out to verify the simulation of residual stress values before and after UIT. By the results, optimization of UIT application could effectively reduce the residual stress concentration after welding process. Residual tensile stress of welded joints after UIT is transformed into residual compressive stress. UIT formed a residual compressive stress layer with a thickness of about 0.13 mm on the plate. The numerical simulation results are consistent with the experimental results. The work in this paper could provide theoretical basis and technical support for the reasonable evaluation of the ultrasonic impact on residual stress elimination and mechanical properties improvement of welded joints.

A Probabilistic Evaluation Model for Welding Residual Stress Distribution at Piping Joint in Probabilistic Fracture Mechanics Analysis

2008 ◽  
Author(s):  
Hiroto Itoh ◽  
Jinya Katsuyama ◽  
Kunio Onizawa
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Fracture Mechanics ◽  
Failure Probability ◽  
Evaluation Model ◽  
Residual Stress Distribution ◽  
Welding Residual Stress ◽  
Probabilistic Fracture Mechanics ◽  
Probabilistic Evaluation ◽  
Aging Knowledge

Stress corrosion cracking (SCC) has been observed at some piping joints made by Austenitic stainless steel in BWR plants. In JAEA, we have been developing probabilistic fracture mechanics (PFM) analysis methods for aged piping based on latest aging knowledge and an analytical code, PASCAL-SP. PASCAL-SP evaluates the failure probability of piping at aged welded joints under SCC by a Monte Carlo method. We proposes a simplified probabilistic model which can be applied to the failure probability analysis based on PFM for welded joint of piping considering the uncertainty of welding residual stress. And the probabilistic evaluation model is introduced to PASCAL-SP. A parametric PFM analysis concerning uncertainties of residual stress distribution using PASCAL-SP was performed. The PFM analysis showed that the uncertainties of residual stress distribution largely influenced break probability. The break probability increased with increasing the uncertainties of residual stress.

Effects of Flange Width Ratio on the Residual Stresses in Welded Monosymmetric I-Section

2014 ◽  
Vol 501-504 ◽  
pp. 574-577
Author(s):  
Zhuang Nan Zhang ◽  
Xin Zhao ◽  
Ya Nan Zhao
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stress Distribution ◽  
Welding Residual Stress ◽  
Width Ratio ◽  
Residual Tensile Stress ◽  
Growth Trend ◽  
Finite Element Software ◽  
Compressive Stresses ◽  
Peak Value

This paper used ANSYS finite element software to simulate the residual stress of the welded monosymmetric I-section and obtain residual stress distribution curves, analyzed the influence of flange width ratio on welding residual stress peak value and the stress distribution. The studies have shown that: with the flange width ratio decrease gradually, peak value of residual stress in flange and web is to increase; peak value of residual tensile stresses in both flange and web close to the steel yield strength fy, peak value of residual compressive stresses is 0.4fy in wide flange and the web near wide flange and in narrow flange and web near narrow flange is 0.3fy; the distribution of the residual tensile stress in the flange and web have growth trend.

Measurement of Residual Stresses within a PWR Swaged Heater Tube

2011 ◽  
Vol 70 ◽  
pp. 279-284 ◽  
Author(s):  
D.M. Goudar ◽  
Ed J. Kingston ◽  
Mike C. Smith ◽  
Sayeed Hossain
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Stress Measurement ◽  
Measurement Techniques ◽  
Residual Stress Distribution ◽  
Hole Drilling ◽  
Shear Stresses ◽  
Outer Diameter ◽  
Near Surface ◽  
Heater Tube

Frequent failures of the pressuriser heater tubes used in Pressurised Water Reactors (PWRs) have been found. Axial cracks initiating from the tube outer diameter have been detected in some tubes as well as the resulting electrical problems. Replacement of the heater tubes requires an undesirably prolonged plant shutdown. In order to better understand these failures a series of residual stress measurements were carried out to obtain the near surface and through-thickness residual stress profiles in a stainless steel pressuriser heater tube. Three different residual stress measurement techniques were employed namely, Deep-Hole Drilling (DHD), Incremental Centre Hole Drilling (ICHD) and Sachs’ Boring (SB) to measure the through thickness residual stress distribution in the heater tubes. Results showed that the hoop stresses measured using all three techniques were predominantly tensile at all locations, while the axial stresses were found to be tensile at the surface and both tensile and compressive as they reduce to small magnitudes within the tube. The magnitude of the in-plane shear stresses was small at all measurement depths at all locations. The various measurement methods were found to complement each other well. All the measurements revealed a characteristic profile for the through-thickness residual stress distribution.

Sign in / Sign up

Export Citation Format

Share Document