In Situ Verification of Numerical Model of Water Hammer in Slurries

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Apoloniusz Kodura ◽  
Katarzyna Weinerowska-Bords ◽  
Wojciech Artichowicz ◽  
Michał Kubrak ◽  
Paweł Stefanek
Keyword(s):  
Numerical Model ◽  
Transient Flow ◽  
Security Threats ◽  
Pump Operation ◽  
Pipeline Network ◽  
Numerical Tests ◽  
In Situ Experiments ◽  
Industrial Pipeline ◽  
Valve Operation

This paper presents a numerical model of transient flow in a pressure slurry pipeline network with verification based on in situ measurements. The model, primarily verified in laboratory conditions, has been extended and applied to the case of a large and complex slurry pipeline network in Poland. In the model, the equivalent density concept was applied. In situ experiments were performed for various unsteady flow episodes, caused by different pump operation strategies in the industrial pipeline network. Based on the measurements of slurry concentration and pressure variations, the numerical model was tested and verified. A satisfactory coincidence between the calculated and the observed pressure characteristics was achieved. Additional numerical tests led to important conclusions concerning safe pump and valve operation and system security threats.

An in situ and ex situ TEM study of the formation of thin cobalt silicide films by molecular beam epitaxy on the silicon (100) surface

1988 ◽  
Vol 46 ◽  
pp. 884-885
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove ◽  
R. T. Tung
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Defect Density ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Metal Base ◽  
In Situ Experiments ◽  
Potential Applications

The cobalt disilicide/silicon system has potential applications as a metal-base and as a permeable-base transistor. Although thin, low defect density, films of CoSi2 on Si(111) have been successfully grown, there are reasons to believe that Si(100)/CoSi2 may be better suited to the transmission of electrons at the silicon/silicide interface than Si(111)/CoSi2. A TEM study of the formation of CoSi2 on Si(100) is therefore being conducted. We have previously reported TEM observations on Si(111)/CoSi2 grown both in situ, in an ultra high vacuum (UHV) TEM and ex situ, in a conventional Molecular Beam Epitaxy system.The procedures used for the MBE growth have been described elsewhere. In situ experiments were performed in a JEOL 200CX electron microscope, extensively modified to give a vacuum of better than 10-9 T in the specimen region and the capacity to do in situ sample heating and deposition. Cobalt was deposited onto clean Si(100) samples by thermal evaporation from cobalt-coated Ta filaments.

Electron and ion irradiation-induced dissolution of mechanical twins in the intermetalic U3Si: An in situ HVEM study

1989 ◽  
Vol 47 ◽  
pp. 652-653
Author(s):  
Charles W. Allen ◽  
Robert C. Birtcher
Keyword(s):  
Elevated Temperatures ◽  
Ion Irradiation ◽  
Ion Beam ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Heavy Ion ◽  
High Energy ◽  
Mechanical Twinning ◽  
In Situ Experiments

The uranium silicides, including U3Si, are under study as candidate low enrichment nuclear fuels. Ion beam simulations of the in-reactor behavior of such materials are performed because a similar damage structure can be produced in hours by energetic heavy ions which requires years in actual reactor tests. This contribution treats one aspect of the microstructural behavior of U3Si under high energy electron irradiation and low dose energetic heavy ion irradiation and is based on in situ experiments, performed at the HVEM-Tandem User Facility at Argonne National Laboratory. This Facility interfaces a 2 MV Tandem ion accelerator and a 0.6 MV ion implanter to a 1.2 MeV AEI high voltage electron microscope, which allows a wide variety of in situ ion beam experiments to be performed with simultaneous irradiation and electron microscopy or diffraction.At elevated temperatures, U3Si exhibits the ordered AuCu3 structure. On cooling below 1058 K, the intermetallic transforms, evidently martensitically, to a body-centered tetragonal structure (alternatively, the structure may be described as face-centered tetragonal, which would be fcc except for a 1 pet tetragonal distortion). Mechanical twinning accompanies the transformation; however, diferences between electron diffraction patterns from twinned and non-twinned martensite plates could not be distinguished.

A computer-control program for TEM in situ fatigue experiments

1989 ◽  
Vol 47 ◽  
pp. 620-621
Author(s):  
Kenneth S. Vecchio ◽  
John A. Hunt
Keyword(s):  
Slow Crack Growth ◽  
Computer Control ◽  
Control Program ◽  
Video Tape ◽  
Computer Control System ◽  
Transmission Electron ◽  
In Situ Experiments ◽  
Tremendous Amount ◽  
And Control

In-situ experiments conducted within a transmission electron microscope provide the operator a unique opportunity to directly observe microstructural phenomena, such as phase transformations and dislocation-precipitate interactions, “as they happen”. However, in-situ experiments usually require a tremendous amount of experimental preparation beforehand, as well as, during the actual experiment. In most cases the researcher must operate and control several pieces of equipment simultaneously. For example, in in-situ deformation experiments, the researcher may have to not only operate the TEM, but also control the straining holder and possibly some recording system such as a video tape machine. When it comes to in-situ fatigue deformation, the experiments became even more complicated with having to control numerous loading cycles while following the slow crack growth. In this paper we will describe a new method for conducting in-situ fatigue experiments using a camputer-controlled tensile straining holder.The tensile straining holder used with computer-control system was manufactured by Philips for the Philips 300 series microscopes. It was necessary to modify the specimen stage area of this holder to work in the Philips 400 series microscopes because the distance between the optic axis and holder airlock is different than in the Philips 300 series microscopes. However, the program and interfacing can easily be modified to work with any goniometer type straining holder which uses a penrmanent magnet motor.

Coliform transport in a pristine reservoir: modeling and field studies

1998 ◽  
Vol 37 (2) ◽  
pp. 137-144 ◽  
Author(s):  
Elisa Garvey ◽  
John E. Tobiason ◽  
Michael Hayes ◽  
Evelyn Wolfram ◽  
David A. Reckhow ◽  
...  
Keyword(s):  
Model Development ◽  
Fate And Transport ◽  
Field Studies ◽  
Meteorological Conditions ◽  
Reservoir Modeling ◽  
Vertical Circulation ◽  
Quality Model ◽  
Circulation Patterns ◽  
In Situ Experiments

This paper reports on field studies and model development aimed at understanding coliform fate and transport in the Quabbin Reservoir, an oligotrophic drinking water supply reservoir. An investigation of reservoir currents suggested the importance of wind driven phenomena, and that both lateral and vertical circulation patterns exist. In-situ experiments of coliform decay suggested dependence on light intensity and yielded an appropriate decay coefficient to be used in CE-QUAL-W2, a two-dimensional hydrodynamic and water quality model. Modeling confirmed the sensitivity of reservoir outlet concentration to vertical variability within the reservoir, meteorological conditions, and location of coliform source.

scholarly journals Upscaling THM modeling from small-scale to full-scale in-situ experiments in the Callovo-Oxfordian claystone

2021 ◽  
Vol 144 ◽  
pp. 104582
Author(s):  
D.M. Seyedi ◽  
C. Plúa ◽  
M. Vitel ◽  
G. Armand ◽  
J. Rutqvist ◽  
...  
Keyword(s):  
Full Scale ◽  
Small Scale ◽  
In Situ Experiments

scholarly journals Memory Effect on a LDH/zeolite A Composite: An XRD In Situ Study

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2102
Author(s):  
Breno G. P. Bezerra ◽  
Lindiane Bieseki ◽  
Mariele I. S. de Mello ◽  
Djalma R. da Silva ◽  
Cristiane B. Rodella ◽  
...  
Keyword(s):  
Memory Effect ◽  
Inert Atmosphere ◽  
Effect Study ◽  
Physical Mixture ◽  
Zeolite A ◽  
Three Samples ◽  
In Situ Experiments ◽  
Double Hydroxide ◽  
Rehydration Process

In this memory effect study, hydrotalcite-type compounds in the lamellar double hydroxide-like (LDH)/zeolite A composite material were analyzed using X-Ray Diffration XRD) in situ experiments. Three samples were analyzed: Al,Mg-LDH, Al,Mg-LDH/ZA composite, and a physical mixture (50/50 wt%) of zeolite A and Al,Mg-LDH. The Al,Mg-LDH sample was treated at 500 °C in an O2 atmosphere and subsequently rehydrated. The Al,Mg-LDH/ZA composites had three treatments: one was performed at 300 °C in a He atmosphere, and two treatments were performed with an O2 atmosphere at 300 and 500 °C. In the physical mixture, two treatments were carried out under O2 flow at 500 °C and under He flow at 300 °C. Both went through the rehydration process. All samples were also analyzed by energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM). The results show that the LDH phase in the Al,Mg-LDH/ZA compounds has memory effects, and thus, the compound can be calcined and rehydrated. For the LDH in the composite, the best heat treatment system is a temperature of 300 °C in an inert atmosphere.

scholarly journals Effects of Infills in the Seismic Performance of an RC Factory Building in Pakistan

Buildings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 276
Author(s):  
Nisar Ali Khan ◽  
Giorgio Monti ◽  
Camillo Nuti ◽  
Marco Vailati
Keyword(s):  
Numerical Model ◽  
Construction Materials ◽  
Building Codes ◽  
Construction Technique ◽  
Infill Walls ◽  
Mortar Strength ◽  
Materials Used ◽  
Seismic Response Of Buildings

Infilled reinforced concrete (IRC) frames are a very common construction typology, not only in developing countries such as Pakistan but also in southern Europe and Western countries, due to their ease of construction and less technical skills required for the construction. Their performance during past earthquakes has been in some cases satisfactory and in other cases inadequate. Significant effort has been made among researchers to improve such performance, but few have highlighted the influence of construction materials used in the infill walls. In some building codes, infills are still considered as non-structural elements, both in the design of new buildings and, sometimes, in the assessment of existing buildings. This is mainly due to some difficulties in modeling their mechanical behavior and also the large variety of typologies, which are difficult to categorize. Some building codes, for example, Eurocode, already address the influence of infill walls in design, but there is still a lack of homogeneity among different codes. For example, the Pakistan building code (PBC) does not address infills, despite being a common construction technique in the country. Past earthquake survey records show that construction materials and infill types significantly affect the seismic response of buildings, thus highlighting the importance of investigating such parameters. This is the object of this work, where a numerical model for infill walls is introduced, which aims at predicting their failure mode, as a function of some essential parameters, such as the friction coefficient between mortar and brick surface and mortar strength, usually disregarded in previous models. A comprehensive case study is presented of a three-story IRC frame located in the city of Mirpur, Pakistan, hit by an earthquake of magnitude 5.9 on 24 September 2019. The results obtained from the numerical model show good agreement with the damage patterns observed in situ, thus highlighting the importance of correctly modeling the infill walls when seismically designing or assessing Pakistani buildings that make use of this technology.

scholarly journals Advanced experimental approaches to marine water-column biogeochemical processes

2017 ◽  
Vol 75 (1) ◽  
pp. 30-42 ◽  
Author(s):  
Louis Legendre ◽  
Richard B Rivkin ◽  
Nianzhi Jiao
Keyword(s):  
Water Column ◽  
Numerical Models ◽  
Free Water ◽  
Sea Surface ◽  
Biogeochemical Processes ◽  
In Situ Experiments ◽  
Technological Developments ◽  
Approaches To Study ◽  
Experimental Approaches

Abstract This “Food for Thought” article examines the potential uses of several novel scientific and technological developments, which are currently available or being developed, to significantly advance or supplement existing experimental approaches to study water-column biogeochemical processes (WCB-processes). After examining the complementary roles of observation, experiments and numerical models to study WCB-processes, we focus on the main experimental approaches of free-water in situ experiments, and at-sea and on-land meso- and macrocosms. We identify some of the incompletely resolved aspects of marine WCB-processes, and explore advanced experimental approaches that could be used to reduce their uncertainties. We examine three such approaches: free-water experiments of lengthened duration using bioArgo floats and gliders, at-sea mesocosms deployed several 100s m below the sea-surface using new biogeochemical sensors, and 50 m-tall on-land macrocosms. These approaches could lead to significant progress in concepts related to marine WCB-processes.

Pulsed Microwave Processing of High-TC Superconducting Films

1992 ◽  
Vol 269 ◽  
Author(s):  
R. B. James ◽  
R. A. Alvarez ◽  
A. K. Stamper ◽  
X. J. Bao ◽  
T. E. Schlesinger ◽  
...  
Keyword(s):  
Phase Transition ◽  
Barium Copper Oxide ◽  
Precursor Film ◽  
Silicon Substrates ◽  
Molten Layer ◽  
Time Resolved ◽  
Barium Copper ◽  
In Situ Experiments ◽  
Yttrium Barium

ABSTRACTWe have used 2.0-μsec microwave pulses at a frequency of 2.856 GHz to rapidly heat thin amorphous yttrium-barium-copper-oxide (YBCO) films deposited onto silicon substrates. The samples were irradiated inside a WR-284 waveguide by single-pass TE10 pulses in a traveling wave geometry. X-ray diffractometry studies show that an amorphous-to-crystalline phase transition occurs for incident pulse powers exceeding about 6 MW, in which case the amorphous YBCO layer is converted to Y2BaCuO5. Microscopy of the irradiated film reveals that the phase transition is brought about by melting of the YBCO precursor film and crystallization of the molten layer upon solidification. Time-resolved in situ experiments of the microwave reflectivity (R) and transmissivity (T) show that there is an abrupt change in R for microwave pulse powers exceeding the melt threshold, so that measurements of R and T can be used to monitor the onset of surface melting.

Sign in / Sign up

Export Citation Format

Share Document