Numerical Predictions of Three-Dimensional Unsteady Turbulent Film-Cooling for Trailing Edge of Gas-Turbine Blade Using Large Eddy Simulation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Ahmed Khalil ◽  
Hatem Kayed ◽  
Abdallah Hanafi ◽  
Medhat Nemitallah ◽  
Mohamed Habib
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Gas Turbine Blades ◽  
Blowing Ratio ◽  
Eddy Simulation

This work investigates the performance of film-cooling on trailing edge of gas turbine blades using unsteady three-dimensional numerical model adopting large eddy simulation (LES) turbulence scheme in a low Mach number flow regime. This study is concerned with the scaling parameters affecting effectiveness and heat transfer performance on the trailing edge, as a critical design parameter, of gas turbine blades. Simulations were performed using ANSYS-fluentworkbench 17.2. High quality mesh was adapted, whereas the size of cells adjacent to the wall was optimized carefully to sufficiently resolve the boundary layer to obtain insight predictions of the film-cooling effectiveness on a flat plate downstream the slot opening. Blowing ratio, density ratio, Reynolds number, and the turbulence intensity of the mainstream and coolant flow are optimally examined against the film-cooling effectiveness. The predicted results showed a great agreement when compared with the experiments. The results show a distinctive behavior of the cooling effectiveness with blowing ratio variation as it has a dip in vicinity of unity which is explained by the behavior of the vortex entrainment and momentum of coolant flow. The negative effect of the turbulence intensity on the cooling effectiveness is demonstrated as well.

scholarly journals Prediction of Film Cooling Effectiveness of Steam

1982 ◽  
Author(s):  
Je-Chin Han ◽  
P. E. Jenkins
Keyword(s):  
Film Cooling ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Air Cooling ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Gas Turbine Blades ◽  
Fluid Properties ◽  
Three Dimensional Models

The intent of this work is to show, analytically, that superheated steam can provide better film cooling than conventional air for gas turbine blades and vanes. Goldstein’s two-dimensional and Eckert’s three-dimensional models have been reexamined and modified in order to include the effects of thermal-fluid properties of foreign gas injection on the film cooling effectiveness. Based on the modified models, the computed results for steam film cooling effectiveness, showing an increase of 80 to 100 percent when compared with air cooling at the same operating conditions, are presented.

Film Cooling of Gas Turbine Blades: A Study of the Effect of Large Temperature Differences on Film Cooling Effectiveness

1977 ◽  
Vol 99 (1) ◽  
pp. 11-20 ◽  
Author(s):  
M. A. Paradis
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Turbine Blades ◽  
Large Temperature ◽  
Constant Property ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Gas Turbine Blades ◽  
Combustion Gases ◽  
Simple Equations

Experiments have been performed on the film cooling of gas turbine blades in order to study the influence of large temperature differences on the effectiveness of film cooling. A two-dimensional flat plate model was tested in a stream of 1000 K combustion gases flowing at between 110 and 170 m/s. The model was cooled on both sides by jets of air coming from flush angled slots. The range of velocity ratios Uc/Ug covered was from 0.3 to 1.7 and the range of blowing rates was between 0.5 and 5. Film cooling effectiveness was measured and boundary layer traverses were performed. It has been found that once radiation and conduction effects are taken into account, the simple equations proposed by previous workers for the constant property case could be used with little error.

Effect of the In-Hole Vortical Structures on the Cylindrical-Hole Film-Cooling Effectiveness

2020 ◽  
Author(s):  
Shubham Agarwal ◽  
Laurent Gicquel ◽  
Florent Duchaine ◽  
Nicolas Odier ◽  
Jérôme Dombard
Keyword(s):  
Film Cooling ◽  
Turbine Blades ◽  
Hairpin Vortices ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Vortical Structures ◽  
Blowing Ratio ◽  
Eddy Simulation ◽  
Control Film ◽  
Cooling Hole

Abstract Understanding the flow from a cooling hole is very important to be able to properly control film cooling of turbine blades. For this purpose, large eddy simulation (LES) investigation of the flow inside a cylindrical film cooling hole is presented in this paper. Two different geometries, with different hole metering lengths, are investigated at a blowing ratio of 0.5. The main flow structure in the hole are the hairpin vortices that originate from a shear layer formed due to flow separation near the hole entry. The comparison of these hairpin vortices in the two cases with different hole metering length is presented in detail. The results show that in case of the hole with longer length the hairpin vortices dissociate within the hole itself. In such a case a uniform flow is seen at the hole exit. However, when the hole length is significantly decreased, it is shown that these vortices exit the hole and effect the vortex structures outside the hole, thereby accounting for the reduction in film cooling effectiveness. Overall, these results bring forth one other major reason for the reduction in film cooling effectiveness with reduction in hole length, i.e. the exit of in-hole hairpin vortices into the crossflow.

Experimental and Numerical Investigation of Trailing Edge Film Cooling by Circular Coolant Wall Jets Ejected From a Slot With Internal Rib Arrays

2003 ◽  
Author(s):  
P. Martini ◽  
A. Schulz ◽  
S. Wittig
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Numerical Data ◽  
Trailing Edge ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Edge Features ◽  
Cooling Air

The present study concentrates on the experimental and computational investigation of a cooled trailing edge in a modern turbine blade. The trailing edge features a pressure side cutback and a slot, stiffened by two rows of evenly spaced ribs in an inline configuration. Cooling air is ejected through the slot and forms a cooling film on the trailing edge cutback region. In the present configuration the lateral spacing of the ribs equals two times their width. The height of the ribs, i.e. the height of the slot equals their width. Since the ribs are provided with fillet radii of half the slot height in size, circular coolant jets are exiting the slot tangentially to the trailing edge cutback. The adiabatic wall temperature mappings on the trailing edge cutback indicate that strong three-dimensional flow interaction between the coolant jets and the hot main flow takes place in such a way that two or more coolant jets coalesce depending on the blowing ratio. Experimental and numerical data to be presented in the present study include adiabatic film cooling effectiveness on the trailing edge cutback, the pressure distribution along the internal ribbed passage as well as slot discharge coefficients for different blowing ratios ranging from M = 0.35 to 1.1.

Experimental and Numerical Investigation of Trailing Edge Film Cooling by Circular Coolant Wall Jets Ejected From a Slot With Internal Rib Arrays

2004 ◽  
Vol 126 (2) ◽  
pp. 229-236 ◽  
Author(s):  
P. Martini ◽  
A. Schulz
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Numerical Data ◽  
Trailing Edge ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Edge Features ◽  
Cooling Air

The present study concentrates on the experimental and computational investigation of a cooled trailing edge in a modern turbine blade. The trailing edge features a pressure side cutback and a slot, stiffened by two rows of evenly spaced ribs in an inline configuration. Cooling air is ejected through the slot and forms a cooling film on the trailing edge cutback region. In the present configuration the lateral spacing of the ribs equals two times their width. The height of the ribs, i.e., the height of the slot equals their width. Since the ribs are provided with fillet radii of half the slot height in size, circular coolant jets are exiting the slot tangentially to the trailing edge cutback. The adiabatic wall temperature mappings on the trailing edge cutback indicate that strong three-dimensional flow interaction between the coolant jets and the hot main flow takes place in such a way that two or more coolant jets coalesce depending on the blowing ratio. Experimental and numerical data to be presented in the present study include adiabatic film cooling effectiveness on the trailing edge cutback, the pressure distribution along the internal ribbed passage as well as slot discharge coefficients for different blowing ratios ranging from M=0.35 to 1.1.

Very Large Eddy Simulation of Film Cooling Effectiveness on Trailing Edge Cutback

2020 ◽  
Author(s):  
Xin Yan
Keyword(s):  
Gas Turbine ◽  
Vortex Shedding ◽  
Film Cooling ◽  
Cooling Effect ◽  
Detached Eddy Simulation ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Eddy Simulation ◽  
Large Eddy

Abstract The trailing edge of high pressure gas turbine blade in aeroengine is usually designed as thin as possible to achieve higher aerodynamic efficiency. However, as the inlet temperature of modern gas turbine is continuously increasing, thermal stress in a thin trailing edge will become much significant, resulting in possibilities of erosion and creep problems. To find a balance between these two conflicting goals, one method is the use of pressure-side cutback, which extends into the coolant slot to get film cooling and also achieves a thin trailing edge. Due to the interactions between mainstream and coolant flow, film cooling effect on trailing edge cutback is significantly affected by the vortex shedding downstream the cooling slot. To resolve the coherent flow structures and understand their role on film cooling effect on trailing-edge cutback, this paper implemented a Very Large Eddy Simulation (VLES) model into the solver ANSYS Fluent with user defined functions. By introducing a resolution control factor, the turbulence viscosity predicted by transient SST k-ω model was corrected and the VLES computations were realized in the whole computational region. With the VLES method, film cooling effectiveness distributions on trailing-edge cutback at three blowing ratios were computed and compared against the experimental data. The coherent unsteadiness in cutback region was visualized to reveal the mixing process between mainstream and coolant flow. The numerical accuracies between different unsteady prediction methods, i.e. URANS (Unsteady Reynolds Averaged Navier-Stokes), SAS (Scale-Adaptive Simulation), DES (Detached Eddy Simulation), DDES (Delayed-Detached Eddy Simulation), SBES (Stress-Blended Eddy Simulation), and VLES were compared with respect to the resolutions of cooling effect and vortex shedding. The results show that the periodic vortex shedding induced by the interactions between mainstream and coolant is the main factor that affecting the cooling performance on cutback. VLES method has a comparable accuracy in predicting the film cooling effect on trailing edge cutback with DDES and SBES approaching. In the detached shear layer, VLES method exhibits a good ability to resolve coherent unsteadiness caused by vortex shedding. Compared with URANS and SAS methods, the VLES method has a higher accuracy in resolving the periodic vortex shedding and film cooling effectiveness distributions, especially in low blowing ratio cases.

Heat Transfer Coefficients and Film Cooling Effectiveness on the Squealer Tip of a Gas Turbine Blade

2003 ◽  
Vol 125 (4) ◽  
pp. 648-657 ◽  
Author(s):  
Jae Su Kwak ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Rotor Blade ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio

Experimental investigations were performed to measure the detailed heat transfer coefficients and film cooling effectiveness on the squealer tip of a gas turbine blade in a five-bladed linear cascade. The blade was a two-dimensional model of a first stage gas turbine rotor blade with a profile of the GE-E3 aircraft gas turbine engine rotor blade. The test blade had a squealer (recessed) tip with a 4.22% recess. The blade model was equipped with a single row of film cooling holes on the pressure side near the tip region and the tip surface along the camber line. Hue detection based transient liquid crystals technique was used to measure heat transfer coefficients and film cooling effectiveness. All measurements were done for the three tip gap clearances of 1.0%, 1.5%, and 2.5% of blade span at the two blowing ratios of 1.0 and 2.0. The Reynolds number based on cascade exit velocity and axial chord length was 1.1×106 and the total turning angle of the blade was 97.9 deg. The overall pressure ratio was 1.2 and the inlet and exit Mach numbers were 0.25 and 0.59, respectively. The turbulence intensity level at the cascade inlet was 9.7%. Results showed that the overall heat transfer coefficients increased with increasing tip gap clearance, but decreased with increasing blowing ratio. However, the overall film cooling effectiveness increased with increasing blowing ratio. Results also showed that the overall film cooling effectiveness increased but heat transfer coefficients decreased for the squealer tip when compared to the plane tip at the same tip gap clearance and blowing ratio conditions.

Simulation Film Cooling in the Leading Edge Region of a Turbine Blade (Trench Effect on Film Effectiveness from Cylinder in Crossflow)

2014 ◽  
Vol 554 ◽  
pp. 317-321
Author(s):  
Mohamad Rasidi Bin Pairan ◽  
Norzelawati Binti Asmuin ◽  
Hamidon bin Salleh
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Leading Edge ◽  
Edge Region ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Hot Gas ◽  
Cooling Technique

Film cooling is one of the cooling techniques applied to the turbine blade. Gas turbine used film cooling technique to protect turbine blade from directly expose to the hot gas to avoid the blade from defect. The focus of this investigation is to investigate the effect of embedded three difference depth of trench at coolant holes geometry. Comparisons are made at four difference blowing ratios which are 1.0, 1.25 and 1.5. Three configuration leading edge with depth Case A (0.0125D), Case B (0.0350D) and Case C (0.713D) were compared to leading edge without trench. Result shows that as blowing ratio increased from 1.0 to 1.25, the film cooling effectiveness is increase for leading edge without trench and also for all cases. However when the blowing ratio is increase to 1.5, film cooling effectiveness is decrease for all cases. Overall the Case B with blowing ratio 1.25 has the best film cooling effectiveness with significant improvement compared to leading edge without trench and with trench Case A and Case C.

Flow Dynamics and Film Cooling Effectiveness on a Non-Axisymmetric Contour Endwall in a Two-Dimensional Cascade Passage

2009 ◽  
Author(s):  
Gazi I. Mahmood ◽  
Ross Gustafson ◽  
Sumanta Acharya
Keyword(s):  
Temperature Field ◽  
Flow Field ◽  
Film Cooling ◽  
Free Stream ◽  
Flow Behavior ◽  
Three Dimensional ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Blowing Ratio

The measured flow field and temperature field near a three-dimensional asymmetric contour endwall employed in a linear blade cascade are presented with and without film-cooling flow on the endwall. Flow field temperature and Nusselt number distributions along the asymmetric endwall with wall heating and no film-cooling flow are also reported to show local high heat transfer region on the endwall and justify the locations of the coolant holes. Adiabatic film-cooling effectiveness along the endwall is then measured to indicate the local effects of the coolant jets. The near endwall flow field and temperature field provide the coolant flow behavior and the interaction of coolant jets with the boundary layer flow. Thus, the local film-cooling effectiveness can be explained with the coolant jet trajectories. The measurements are obtained at the Reynolds number of 2.30×105 based on blade actual chord and inlet velocity, coolant-to-free stream temperature ratio of 0.93, and coolant-to-free stream density ratio of 1.06. The cascade employs the hub side blade section and passage geometry of the first stage rotor of GE-E3 turbine engine. The contour endwall profile is employed on the bottom endwall only in the cascade. The blowing ratio of the film-cooling flow varies from 1.0 to 2.4 from 71 discrete cylindrical holes located in the contour endwall. The three-dimensional profile of the endwall varies in height in both the pitchwise and axial directions. The flow field is quantified with the streamwise vorticity and turbulent intensity, pitchwise static pressure difference, flow yaw angle, and pitchwise velocity. Both the flow field and temperature data indicate that the coolant jets cover more distance in the pitchwise and axial direction in the passage as the blowing ratio increases. Thus, the local and average film-cooling effectiveness increase with the blowing ratio.

Sign in / Sign up

Export Citation Format

Share Document