Convective Heat Transfer Investigation of a Confined Air Slot-Jet Impingement Cooling on Corrugated Surfaces With Different Wave Shapes

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Recep Ekiciler ◽  
Muhammet Samet Ali Çetinkaya ◽  
Kamil Arslan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Flow Characteristics ◽  
Jet Impingement ◽  
Working Fluid ◽  
Bottom Surface ◽  
Air Jet ◽  
Corrugated Surfaces ◽  
Energy Equations

In this study, air jet impingement on flat, triangular-corrugated, and sinusoidal-corrugated surfaces was numerically investigated. Bottom surface was subjected to constant surface temperature. Air was the working fluid. The air exited from a rectangular shaped slot and impinged on the bottom surface. The Reynolds number was changed between 125 and 500. The continuity, momentum, and energy equations were solved using the finite volume method. The effect of the shape of bottom surface on heat and flow characteristics was investigated in detail. Average and local Nusselt number were calculated for each case. It was found out that Nusselt number increases by increasing the Reynolds number. The optimum conditions were established to get much more enhancement in terms of performance evaluation criterion (PEC). It was revealed that the shape of the cooling surface (bottom wall) influences the heat transfer substantially.

Numerical Simulation of Oblique Air Jet Impingement on a Heated Flat Plate

2016 ◽  
Vol 9 (1) ◽  
Author(s):  
Abhishek B. Bhagwat ◽  
Arunkumar Sridharan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Flat Plate ◽  
Numerical Study ◽  
Jet Impingement ◽  
Maximum Heat ◽  
Air Jet ◽  
Maximum Heat Transfer ◽  
Vertical Jet

Jet impingement cooling has been studied extensively as this finds applications in the areas of reactor safety, electronic cooling, etc. Here, the convective heat transfer process between the air jet impingement on a uniformly heated inclined flat plate is studied numerically. In this numerical study, 3D simulations are carried out using commercial CFD code to investigate the effect of angle of inclination of plate, Reynolds number, and distance between the nozzle exit and the plate on the heat transfer characteristics. V2F model has been used to model turbulence for various nozzle–plate distance and Reynolds number. It can be concluded that V2F model predicts the Nusselt number variation on the plate satisfactorily. It is observed that point of maximum heat transfer is at the stagnation point in case of vertical jet impinging on a horizontal plate, while it shifts away from the point of impingement for the case of a vertical jet impinging on an inclined flat surface. The shift is toward the “compression side” or the “uphill side” of the air jet. The results are validated with experimental data from the literature. Detailed analysis of local heat transfer coefficients, velocity contours, temperature contours, and Nusselt number variations on the flat plate is presented.

Effects of a High Porous Material on Heat Transfer and Flow in a Circular Tube

2008 ◽  
Vol 131 (2) ◽  
Author(s):  
Koichi Ichimiya ◽  
Tetsuaki Takeda ◽  
Takuya Uemura ◽  
Tetsuya Norikuni
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Porous Material ◽  
Entropy Generation ◽  
Circular Tube ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Equivalent Diameter

This paper describes the heat transfer and flow characteristics of a heat exchanger tube filled with a high porous material. Fine copper wires (diameter: 0.5 mm) were inserted in a circular tube dominated by thermal conduction and forced convection. The porosity was from 0.98 to 1.0. The working fluid was air. The hydraulic equivalent diameter was cited as the characteristic length in the Nusselt number and the Reynolds number. The Nusselt number and the friction factor were expressed as functions of the Reynolds number and porosity. The thermal performance was evaluated by the ratio of the Nusselt number with and without a high porous material and the entropy generation. It was recognized that the high porous material was effective in low Reynolds numbers and the Reynolds number, which minimized the entropy generation existed.

Effects of a High Porous Material on Heat Transfer and Flow in a Circular Tube

2007 ◽  
Author(s):  
Koichi Ichimiya ◽  
Tetsuaki Takeda ◽  
Takuya Uemura ◽  
Tetsuya Norikuni
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Porous Material ◽  
Entropy Generation ◽  
Circular Tube ◽  
Copper Wire ◽  
Flow Characteristics ◽  
Working Fluid ◽  
Equivalent Diameter

This paper describes the heat transfer and flow characteristics of a heat exchanger tube filled with a high porous material. Fine copper wire (diamete: 0.5 mm) was inserted in a circular tube dominated by thermal conduction and forced convection. The porosity was from 0.98 to 1.0. Working fluid was air. Hydraulic equivalent diameter was cited as the characteristic length in Nusselt number and Reynolds number. Nusselt number and friction factor were expressed as functions of Reynolds number and porosity. Thermal performance was evaluated by the ratio of Nusselt number with and without a high porous material and the entropy generation. It was recognized that the high porous material was effective in low Reynolds number and the Reynolds number which minimized the entropy generation existed.

Convective Heat Transfer From a Heated Plate to the Orthogonally Impinging Air Jet

2016 ◽  
Vol 8 (4) ◽  
Author(s):  
Abhishek B. Bhagwat ◽  
Arunkumar Sridharan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Jet Impingement ◽  
Secondary Peak ◽  
Plate Spacing ◽  
Air Jet ◽  
Plate Distance

The convective heat transfer process between the orthogonal air jet impingement on a uniformly heated flat plate is studied numerically. In this numerical study, three-dimensional (3D) simulations are carried out in Fluent 14.0 to investigate the effect of Reynolds number, distance between nozzle exit and the plate on the heat transfer characteristics. V2F turbulence model has been used to model turbulence. Standard κ–ε, Realizable κ–ε, κ–ε RNG, SST κ–ω, Standard κ–ω, V2F turbulence models have been studied for orthogonal jet impingement in this work. It is observed that for jet exit to plate distance (Z/d) of 0.5 ≤ Z/d ≤ 6, V2F model is best suited. For Z/d ≤ 0.5 and Z/d ≥ 6, numerical results vary significantly from the experimental results. Reynolds number of 12,000, 20,000, and 28,000 has been studied. In this paper, results for various jet exit to the plate distance (Z/d) from 0.5 to 10 are presented. At low jet plate spacing Z/d < 4, secondary peak in Nusselt number distribution over the plate is visible in experimental results. V2F model correctly predicts the secondary peak in Nusselt number variation over the plate. Other models fail to predict the secondary peak which is of significant importance in air jet impingement at low jet-plate spacing (Z/d < 4).

Heat transfer of multi-slot nozzle air jet impingement with different Reynolds number

2020 ◽  
pp. 116470
Author(s):  
Jinqi Zhu ◽  
Ruifeng Dou ◽  
Ye Hu ◽  
Shixing Zhang ◽  
Xuyun Wang
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Jet Impingement ◽  
Slot Nozzle ◽  
Air Jet

Heat Transfer and Pressure Loss Characteristics of Pin-Fins With Different Shapes in a Wide Channel

2017 ◽  
Author(s):  
Jin Xu ◽  
Jiaxu Yao ◽  
Pengfei Su ◽  
Jiang Lei ◽  
Junmei Wu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Thermal Performance ◽  
Pressure Loss ◽  
Bottom Surface ◽  
Number Range ◽  
Pin Fin ◽  
Nominal Diameter ◽  
Pin Fins

Convective heat transfer enhancement and pressure loss characteristics in a wide rectangular channel (AR = 4) with staggered pin fin arrays are investigated experimentally. Six sets of pin fins with the same nominal diameter (Dn = 8mm) are tested, including: Circular, Elliptic, Oblong, Dropform, NACA and Lancet. The relative spanwise pitch (S/Dn = 2) and streamwise pitch (X/Dn = 4.5) are kept the same for all six sets. Same nominal diameter and arrangement guarantee the same blockage area in the channel for each set. Reynolds number based on channel hydraulic diameter is from 10000 to 70000 with an increment of 10000. Using thermochromic liquid crystal (R40C20W), heat transfer coefficients on bottom surface of the channel are achieved. The obtained friction factor, Nusselt number and overall thermal performance are compared with the previously published data from other groups. The averaged Nusselt number of Circular pin fins is the largest in these six pin fins under different Re. Though Elliptic has a moderate level of Nusselt number, its pressure loss is next to the lowest. Elliptic pin fins have pretty good overall thermal performance in the tested Reynolds number range. When Re>40000, Lancet has a same level of performance as Circular, but its pressure loss is much lower than Circular. These two types are both promising alternative configuration to Circular pin fin used in gas turbine blade.

scholarly journals Enhanced heat transfer characteristics of conjugated air jet impingement on a finned heat sink

2017 ◽  
Vol 21 (1 Part A) ◽  
pp. 279-288 ◽  
Author(s):  
Shuxia Qiu ◽  
Peng Xu ◽  
Liping Geng ◽  
Arun Mujumdar ◽  
Zhouting Jiang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Cooling System ◽  
Flow Characteristics ◽  
Jet Impingement ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Air Jet

Air jet impingement is one of the effective cooling techniques employed in micro-electronic industry. To enhance the heat transfer performance, a cooling system with air jet impingement on a finned heat sink is evaluated via the computational fluid dynamics method. A two-dimensional confined slot air impinging on a finned flat plate is modeled. The numerical model is validated by comparison of the computed Nusselt number distribution on the impingement target with published experimental results. The flow characteristics and heat transfer performance of jet impingement on both of smooth and finned heat sinks are compared. It is observed that jet impingement over finned target plate improves the cooling performance significantly. A dimensionless heat transfer enhancement factor is introduced to quantify the effect of jet flow Reynolds number on the finned surface. The effect of rectangular fin dimensions on impingement heat transfer rate is discussed in order to optimize the cooling system. Also, the computed flow and thermal fields of the air impingement system are examined to explore the physical mechanisms for heat transfer enhancement.

Effect of Variation of Pin-fin Height on Jet Impingement Heat Transfer on a Rotating Surface

2021 ◽  
Author(s):  
Pratik S. Bhansali ◽  
Srinath V. Ekkad
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Gas Turbine ◽  
Average Nusselt Number ◽  
Jet Impingement ◽  
Impinging Jet ◽  
Rotating Disc ◽  
Disc Surface ◽  
Pin Fins

Abstract Heat transfer over rotating surfaces is of particular interest in rotating machinery such as gas turbine engines. The rotation of the gas turbine disc creates a radially outward flow on the disc surface, which may lead to ingress of hot gases into the narrow cavity between the disc and the stator. Impingement of cooling jet is an effective way of cooling the disc and countering the ingress of the hot gases. Present study focusses on investigating the effect of introducing pin-fins over the rotating disc on the heat transfer. The jet Reynolds number has been varied from 5000 to 18000, and the rotating Reynolds number has been varied from 5487 to 12803 for an aluminum disc of thickness 6.35mm and diameter 10.16 cm, over which square pins have been arranged in an inline fashion. Steady state temperature measurements have been taken using thermocouples embedded in the disc close to the target surface, and area average Nusselt number has been calculated. The effects of varying the height of the pin-fins, distance between nozzle and the disc surface and the inclination of the impinging jet with the axis of rotation have also been studied. The results have been compared with those for a smooth aluminum disc of equal dimensions and without any pin-fins. The average Nusselt number is significantly enhanced by the presence of pin fins. In the impingement dominant regime, where the effect of disc rotation is minimal for a smooth disc, the heat transfer increases with rotational speed in case of pin fins. The effect of inclination angle of the impinging jet is insignificant in the range explored in this paper (0° to 20°).

Experimental Investigation of Air–Water Mist Jet Impingement Cooling Over a Heated Cylinder

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Chunkyraj Khangembam ◽  
Dushyant Singh
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Stagnation Point ◽  
Jet Impingement ◽  
Water Mist ◽  
Heated Cylinder ◽  
Air Jet ◽  
The Heat Transfer Coefficient

Experimental investigation on heat transfer mechanism of air–water mist jet impingement cooling on a heated cylinder is presented. The target cylinder was electrically heated and was maintained under the boiling temperature of water. Parametric studies were carried out for four different values of mist loading fractions, Reynolds numbers, and nozzle-to-surface spacings. Reynolds number, Rehyd, defined based on the hydraulic diameter, was varied from 8820 to 17,106; mist loading fraction, f ranges from 0.25% to 1.0%; and nozzle-to-surface spacing, H/d was varied from 30 to 60. The increment in the heat transfer coefficient with respect to air-jet impingement is presented along with variation in the heat transfer coefficient along the axial and circumferential direction. It is observed that the increase in mist loading greatly increases the heat transfer rate. Increment in the heat transfer coefficient at the stagnation point is found to be 185%, 234%, 272%, and 312% for mist loading fraction 0.25%, 0.50%, 0.75%, and 1.0%, respectively. Experimental study shows identical increment in stagnation point heat transfer coefficient with increasing Reynolds number, with lowest Reynolds number yielding highest increment. Stagnation point heat transfer coefficient increased 263%, 259%, 241%, and 241% as compared to air-jet impingement for Reynolds number 8820, 11,493, 14,166, and 17,106, respectively. The increment in the heat transfer coefficient is observed with a decrease in nozzle-to-surface spacing. Stagnation point heat transfer coefficient increased 282%, 248%, 239%, and 232% as compared to air-jet impingement for nozzle-to-surface spacing of 30, 40, 50, and 60, respectively, is obtained from the experimental analysis. Based on the experimental results, a correlation for stagnation point heat transfer coefficient increment is also proposed.

Submerged Jet Impingement Boiling on a Polished Silicon Surface

2011 ◽  
Author(s):  
Preeti Mani ◽  
Ruander Cardenas ◽  
Vinod Narayanan
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Silicon Surface ◽  
High Speed ◽  
Jet Impingement ◽  
Working Fluid ◽  
Uniform Heat Flux ◽  
Submerged Jet ◽  
Jet Impingement Boiling

Submerged jet impingement boiling has the potential to enhance pool boiling heat transfer rates. In most practical situations, the surface could consist of multiple heat sources that dissipate heat at different rates resulting in a surface heat flux that is non-uniform. This paper discusses the effect of submerged jet impingement on the wall temperature characteristics and heat transfer for a non-uniform heat flux. A mini-jet is caused to impinge on a polished silicon surface from a nozzle having an inner diameter of 1.16 mm. A 25.4 mm diameter thin-film circular serpentine heater, deposited on the bottom of the silicon wafer, is used to heat the surface. Deionized degassed water is used as the working fluid and the jet and pool are subcooled by 20°C. Voltage drop between sensors leads drawn from the serpentine heater are used to identify boiling events. Heater surface temperatures are determined using infrared thermography. High-speed movies of the boiling front are recorded and used to interpret the surface temperature contours. Local heat transfer coefficients indicate significant enhancement upto radial locations of 2.6 jet diameters for a Reynolds number of 2580 and upto 6 jet diameters for a Reynolds number of 5161.

Sign in / Sign up

Export Citation Format

Share Document