scholarly journals The Performance Impact of Integrating Water Storage Into a Chiller-Less Data Center Design

2018 ◽  
Vol 11 (2) ◽  
Author(s):  
Isaac Rose ◽  
Aaron P. Wemhoff ◽  
Amy S. Fleischer
Keyword(s):  
Environmental Conditions ◽  
Data Center ◽  
System Performance ◽  
Storage Tank ◽  
Data Centers ◽  
Storage System ◽  
Water Storage ◽  
Warm Water ◽  
Water Storage Tank ◽  
Operating Temperatures

Abstract Data centers consume an extraordinary amount of electricity, and the rate of consumption is increasing at a rapid pace. Thus, energy efficiency in data center design is of substantial interest since it can have a significant impact on operating costs. The server cooling infrastructure is one area which is ripe for design innovation. Various designs have been considered for air-cooled data centers, and there is growing interest in liquid-cooled server designs. One potential liquid-cooled solution, which reduces the cost of cooling to less than 5% of the information technology (IT) energy use, is a chiller-less or warm water-cooled system, which removes the chiller from the design and lets the cooling water supply vary with changes in the outdoor ambient conditions. While this design has been proven to work effectively in some locations, environmental extremes prevent its more widespread implementation. In this paper, the design and analysis of a cold water storage system are shown to extend the applicability of chiller-less designs to a wider variety of environmental conditions. This can lead to both energy and economic savings for a wide variety of data center installations. A numerical model of a water storage system is developed, validated, and used to analyze the impact of a water storage tank system in a chiller-less data center design featuring outdoor wet cooling. The results show that during times of high wet bulb operating conditions, a water storage tank can be an effective method to significantly reduce chip operating temperatures for warm water-cooled systems by reducing operating temperatures 5–7 °C during the hottest part of the day. The overall system performance was evaluated using both an exergy analysis and a modified power usage effectiveness (PUE) metric defined for the water storage system. This unique situation also necessitates the development of a new exergy definition in order to properly capture the physics of the situation. The impacts of tank size, tank aspect ratio, fill percentage, and charging/discharging time on both the chip temperature and modified PUE are evaluated. It is determined that tank charging time must be carefully matched to environmental conditions in order to optimize impact. Interestingly, the water being stored is initially above ambient, but the overall system performance improves with lower water temperatures. Therefore, heat losses to ambient are found to beneficial to the overall system performance. The results of this analysis demonstrate that in application, data center operators will see a clear performance benefit if water storage systems are used in conjunction with warm water cooling. This application can be extended to data center failure scenarios and could also lead to downsizing of equipment and a clear economic benefit.

Domestic Hot Water Storage Tank: Design and Analysis for Improving Thermal Stratification

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Nathan Devore ◽  
Henry Yip ◽  
Jinny Rhee
Keyword(s):  
Heat Exchanger ◽  
Storage Tank ◽  
Thermal Stratification ◽  
Reverse Flow ◽  
Storage System ◽  
Water Storage ◽  
Hot Water ◽  
Inlet Temperature ◽  
Domestic Hot Water ◽  
Water Storage Tank

Experimental designs for a solar domestic hot water storage system were built in efforts to maximize thermal stratification within the tank. A stratified thermal store has been shown by prior literature to maximize temperature of the hot water drawn from the tank and simultaneously minimize collector inlet temperature required for effective heat transfer from the solar panels, thereby improving the annual performance of domestic solar hot water heating systems (DSHWH) by 30–60%. Our design incorporates partitions, thermal diodes, and a coiled heat exchanger enclosed in an annulus. The thermal diodes are passive devices that promote natural convection currents of hot water upward, while inhibiting reverse flow and mixing. Several variations of heat exchanger coils, diodes and partitions were simulated using ansys Computational Fluid Dynamics, and benchmarked using experimental data. The results revealed that the optimum design incorporated two partitions separated by a specific distance with four diodes for each partition. In addition, it was discovered that varying the length and diameter of the thermal diodes greatly affected the temperature distribution. The thermal diodes and partitions were used to maintain stratification for long periods of time by facilitating natural convective currents and taking advantage of the buoyancy effect. The results of the experiment and simulations proved that incorporating these elements into the design can greatly improve the thermal performance and temperature stratification of a domestic hot water storage tank.

Domestic Hot Water Storage Tank: Design and Analysis for Improving Thermal Stratification

2012 ◽  
Author(s):  
Nathan Devore ◽  
Henry Yip ◽  
Jinny Rhee
Keyword(s):  
Heat Exchanger ◽  
Storage Tank ◽  
Thermal Stratification ◽  
Reverse Flow ◽  
Storage System ◽  
Water Storage ◽  
Hot Water ◽  
Solar Panels ◽  
Domestic Hot Water ◽  
Water Storage Tank

Experimental designs for a solar domestic hot water storage system were built in efforts to maximize thermal stratification within the tank. A stratified thermal store has been shown by prior literature to maximize temperature of the hot water drawn from the tank while simultaneously increasing the temperature delta required for effective heat transfer from the solar panels, thereby improving the annual performance of domestic solar hot water heating systems (DSHWH) by 30%–60%. Our design incorporates partitions, thermal diodes, and a coiled heat exchanger enclosed in an annulus. The thermal diodes are passive devices that promote natural convection currents of hot water upwards, while inhibiting reverse flow and mixing. Several variations of heat exchanger coils, diodes and partitions were simulated using ANSYS Computational Fluid Dynamics, and benchmarked using experimental data. The results revealed that the optimum design incorporated two partitions separated by a specific distance with four diodes for each partition. In addition, it was discovered that varying the length and diameter of the thermal diodes greatly affected the temperature distribution. The thermal diodes and partitions were used to maintain stratification for long periods of time by facilitating natural convective currents and taking advantage of the buoyancy effect. The results of the experiment and simulations proved that incorporating these elements into the design can greatly improve the thermal performance and temperature stratification of a domestic hot water storage tank.

Energy-saving analysis of air source heat pump integrated with a water storage tank for heating applications

2020 ◽  
Vol 180 ◽  
pp. 107029
Author(s):  
Pin Wu ◽  
Zhichao Wang ◽  
Xiaofeng Li ◽  
Zhaowei Xu ◽  
Yingxia Yang ◽  
...  
Keyword(s):  
Energy Saving ◽  
Heat Pump ◽  
Storage Tank ◽  
Water Storage ◽  
Water Storage Tank ◽  
Air Source Heat Pump

scholarly journals The effect of household storage tanks/vessels and user practices on the quality of water: a systematic review of literature

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Musa Manga ◽  
Timothy G. Ngobi ◽  
Lawrence Okeny ◽  
Pamela Acheng ◽  
Hidaya Namakula ◽  
...  
Keyword(s):  
Systematic Review ◽  
Water Quality ◽  
Storage Tank ◽  
Grey Literature ◽  
Water Storage ◽  
Storage Tanks ◽  
Water Storage Tank ◽  
Hygiene Practices ◽  
Quality Of Water ◽  
Vessel Material

Abstract Background Household water storage remains a necessity in many communities worldwide, especially in the developing countries. Water storage often using tanks/vessels is envisaged to be a source of water contamination, along with related user practices. Several studies have investigated this phenomenon, albeit in isolation. This study aimed at developing a systematic review, focusing on the impacts of water storage tank/vessel features and user practices on water quality. Methods Database searches for relevant peer-reviewed papers and grey literature were done. A systematic criterion was set for the selection of publications and after scrutinizing 1106 records, 24 were selected. These were further subjected to a quality appraisal, and data was extracted from them to complete the review. Results and discussion Microbiological and physicochemical parameters were the basis for measuring water quality in storage tanks or vessels. Water storage tank/vessel material and retention time had the highest effect on stored water quality along with age, colour, design, and location. Water storage tank/vessel cleaning and hygiene practices like tank/vessel covering were the user practices most investigated by researchers in the literature reviewed and they were seen to have an impact on stored water quality. Conclusions There is evidence in the literature that storage tanks/vessels, and user practices affect water quality. Little is known about the optimal tank/vessel cleaning frequency to ensure safe drinking water quality. More research is required to conclusively determine the best matrix of tank/vessel features and user practices to ensure good water quality.

scholarly journals Minimum Number of Experimental Data for the Thermal Characterization of a Hot Water Storage Tank

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4741
Author(s):  
María Gasque ◽  
Federico Ibáñez ◽  
Pablo González-Altozano
Keyword(s):  
Experimental Data ◽  
Water Temperature ◽  
Temperature Profile ◽  
Storage Tank ◽  
Water Storage ◽  
Hot Water ◽  
Experimental Temperature ◽  
Inlet Temperature ◽  
Water Storage Tank ◽  
Minimum Number

This paper demonstrates that it is possible to characterize the water temperature profile and its temporal trend in a hot water storage tank during the thermal charge process, using a minimum number of thermocouples (TC), with minor differences compared to experimental data. Four experimental tests (two types of inlet and two water flow rates) were conducted in a 950 L capacity tank. For each experimental test (with 12 TC), four models were developed using a decreasing number of TC (7, 4, 3 and 2, respectively). The results of the estimation of water temperature obtained with each of the four models were compared with those of a fifth model performed with 12 TC. All models were tested for constant inlet temperature. Very acceptable results were achieved (RMSE between 0.2065 °C and 0.8706 °C in models with 3 TC). The models were also useful to estimate the water temperature profile and the evolution of thermocline thickness even with only 3 TC (RMSE between 0.00247 °C and 0.00292 °C). A comparison with a CFD model was carried out to complete the study with very small differences between both approaches when applied to the estimation of the instantaneous temperature profile. The proposed methodology has proven to be very effective in estimating several of the temperature-based indices commonly employed to evaluate thermal stratification in water storage tanks, with only two or three experimental temperature data measurements. It can also be used as a complementary tool to other techniques such as the validation of numerical simulations or in cases where only a few experimental temperature values are available.

Sign in / Sign up

Export Citation Format

Share Document