Influence of Leakage Flows on Hot Gas Ingress

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Marios Patinios ◽  
Irvin L. Ong ◽  
James A. Scobie ◽  
Gary D. Lock ◽  
Carl M. Sangan
Keyword(s):  
Flow Structure ◽  
Turbine Stage ◽  
Co2 Gas ◽  
Gas Concentration ◽  
Leakage Flows ◽  
Hot Gas ◽  
Interface Gaps ◽  
Axial Clearance ◽  
Pass Through ◽  
Do So

One of the most important problems facing gas turbine designers today is the ingestion of hot mainstream gases into the wheel-space between the turbine disk (rotor) and its adjacent casing (stator). A rim seal is fitted at the periphery and a superposed sealant flow—typically fed through the bore of the stator—is used to prevent ingress. The majority of research studies investigating ingress do so in the absence of any leakage paths that exist throughout the engine's architecture. These inevitable pathways are found between the mating interfaces of adjacent pieces of hardware. In an environment where the turbine is subjected to aggressive thermal and centrifugal loading, these interface gaps can be difficult to predict and the resulting leakage flows which pass through them even harder to account for. This paper describes experimental results from a research facility which experimentally models hot gas ingestion into the wheel-space of an axial turbine stage. The facility was specifically designed to incorporate leakage flows through the stator disk; leakage flows were introduced axially through the stator shroud or directly underneath the vane carrier ring. Measurements of CO2 gas concentration, static pressure, and total pressure were used to examine the wheel-space flow structure with and without ingress from the mainstream gas-path. Data are presented for a simple axial-clearance rim-seal. The results support two distinct flow-structures, which are shown to be dependent on the mass-flow ratio of bore and leakage flows. Once the leakage flow was increased above a certain threshold, the flow structure is shown to transition from a classical Batchelor-type rotor-stator system to a vortex-dominated structure. The existence of a toroidal vortex immediately inboard of the outer rim-seal is shown to encourage ingestion.

Influence of Leakage Flows on Hot Gas Ingress

2018 ◽  
Author(s):  
Marios Patinios ◽  
Irvin L. Ong ◽  
James A. Scobie ◽  
Gary D. Lock ◽  
Carl M. Sangan
Keyword(s):  
Flow Structure ◽  
Turbine Stage ◽  
Co2 Gas ◽  
Gas Concentration ◽  
Leakage Flows ◽  
Hot Gas ◽  
Interface Gaps ◽  
Axial Clearance ◽  
Pass Through ◽  
Do So

One of the most important problems facing gas turbine designers today is the ingestion of hot mainstream gases into the wheel-space between the turbine disc (rotor) and its adjacent casing (stator). A rim seal is fitted at the periphery and a superposed sealant flow — typically fed through the bore of the stator — is used to prevent ingress. The majority of research studies investigating ingress do so in the absence of any leakage paths that exist throughout the engine’s architecture. These inevitable pathways are found between the mating interfaces of adjacent pieces of hardware. In an environment where the turbine is subjected to aggressive thermal and centrifugal loading these interface gaps can be difficult to predict and the resulting leakage flows which pass through them even harder to account for. This paper describes experimental results from a research facility which experimentally models hot gas ingestion into the wheel-space of an axial turbine stage. The facility was specifically designed to incorporate leakage flows through the stator disc; leakage flows were introduced axially through the stator shroud or directly underneath the vane carrier ring. Measurements of CO2 gas concentration, static pressure and total pressure were used to examine the wheel-space flow structure with and without ingress from the mainstream gas-path. Data is presented for a simple axial-clearance rim-seal. The results support two distinct flow-structures, which are shown to be dependent on the mass-flow ratio of bore and leakage flows. Once the leakage flow was increased above a certain threshold, the flow structure is shown to transition from a classical Batchelor-type rotor-stator system to a vortex-dominated structure. The existence of a toroidal vortex immediately inboard of the outer rim-seal is shown to encourage ingestion.

Experimental Measurements of Ingestion Through Turbine Rim Seals: Part 1—Externally-Induced Ingress

2011 ◽  
Author(s):  
Carl M. Sangan ◽  
Kunyuan Zhou ◽  
J. Michael Owen ◽  
Oliver J. Pountney ◽  
Mike Wilson ◽  
...  
Keyword(s):  
Three Dimensional ◽  
External Pressure ◽  
Operating Conditions ◽  
Turbine Stage ◽  
Research Facility ◽  
Three Dimensional Flow ◽  
Co2 Gas ◽  
Gas Concentration ◽  
Hot Gas ◽  
New Research

This paper describes a new research facility which experimentally models hot gas ingestion into the wheel-space of an axial turbine stage. Measurements of CO2 gas concentration in the rim-seal region and inside the cavity are used to assess the performance of two generic (though engine-representative) rim-seal geometries in terms of the variation of concentration effectiveness with sealing flow rate. The variation of pressure in the turbine annulus, which governs this externally-induced (EI) ingestion, was obtained from steady pressure measurements downstream of the vanes and near the rim seal upstream of the rotating blades. Although the ingestion through the rim seal is a consequence of an unsteady, three-dimensional flow field and the cause-effect relationship between pressure and the sealing effectiveness is complex, the experimental data is shown to be successfully calculated by simple effectiveness equations developed from a previously published orifice model. The data illustrate that, for similar turbine-stage velocity triangles, the effectiveness can be correlated using a non-dimensional sealing parameter, Φo. In principle, and within the limits of dimensional similitude, these correlations should apply to a geometrically-similar engine at the same operating conditions. Part 2 of this paper describes an experimental investigation of rotationally-induced (RI) ingress, where there is no mainsteam flow and consequently no circumferential variation of external pressure.

Experimental Measurements of Ingestion Through Turbine Rim Seals—Part III: Single and Double Seals

2013 ◽  
Vol 135 (5) ◽  
Author(s):  
Carl M. Sangan ◽  
Oliver J. Pountney ◽  
James A. Scobie ◽  
Mike Wilson ◽  
J. Michael Owen ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Experimental Measurements ◽  
Pressure Measurements ◽  
Turbine Stage ◽  
Research Facility ◽  
Three Dimensional Flow ◽  
Co2 Gas ◽  
Performance Limit ◽  
Gas Concentration ◽  
Hot Gas

This paper describes experimental results from a research facility, which experimentally models hot gas ingress into the wheel-space of an axial turbine stage. Measurements of CO2 gas concentration in the rim-seal region and inside the wheel-space are used to assess the performance of generic (though engine-representative) single and double seals in terms of the variation of concentration effectiveness with sealing flow rate. The variation of pressure in the turbine annulus, which governs externally induced ingress, was obtained from steady pressure measurements downstream of the vanes. The benefit of using double seals is demonstrated: the ingested gas is shown to be predominately confined to the outer wheel-space radially outward of the inner seal; and in the inner wheel-space, radially inward of the inner seal, the effectiveness is shown to be significantly higher. Criteria for ranking the performance of single and double seals are proposed, and the performance limit for any double seal is shown to be one in which the inner seal is exposed to rotationally induced ingress. Although the ingress is a consequence of an unsteady, three-dimensional flow field and the cause-effect relationship between pressure and the sealing effectiveness is complex, the experimental data is shown to be successfully calculated by simple effectiveness equations developed from a theoretical model. The data illustrate that, for similar turbine-stage velocity triangles, the effectiveness can be correlated using two empirical parameters. In principle, these correlations could be extrapolated to a geometrically similar turbine operating at engine-representative conditions.

Experimental Measurements of Ingestion Through Turbine Rim Seals—Part I: Externally Induced Ingress

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Carl M. Sangan ◽  
Oliver J. Pountney ◽  
Kunyuan Zhou ◽  
Mike Wilson ◽  
J. Michael Owen ◽  
...  
Keyword(s):  
Three Dimensional ◽  
External Pressure ◽  
Operating Conditions ◽  
Turbine Stage ◽  
Three Dimensional Flow ◽  
Co2 Gas ◽  
Gas Concentration ◽  
Hot Gas ◽  
Mainstream Flow ◽  
New Research

This paper describes a new research facility which experimentally models hot gas ingestion into the wheel-space of an axial turbine stage. Measurements of the CO2 gas concentration in the rim-seal region and inside the cavity are used to assess the performance of two generic (though engine-representative) rim-seal geometries in terms of the variation of concentration effectiveness with sealing flow rate. The variation of pressure in the turbine annulus, which governs this externally-induced (EI) ingestion, was obtained from steady pressure measurements downstream of the vanes and near the rim seal upstream of the rotating blades. Although the ingestion through the rim seal is a consequence of an unsteady, three-dimensional flow field and the cause-effect relationship between the pressure and the sealing effectiveness is complex, the experimental data is shown to be successfully calculated by simple effectiveness equations developed from a previously published orifice model. The data illustrate that, for similar turbine-stage velocity triangles, the effectiveness can be correlated using a nondimensional sealing parameter, Φo. In principle, and within the limits of dimensional similitude, these correlations should apply to a geometrically-similar engine at the same operating conditions. Part II of this paper describes an experimental investigation of rotationally-induced (RI) ingress, where there is no mainstream flow and consequently no circumferential variation of external pressure.

Experimental Measurements of Ingestion Through Turbine Rim Seals: Part 3—Single and Double Seals

2012 ◽  
Author(s):  
Carl M. Sangan ◽  
James A. Scobie ◽  
J. Michael Owen ◽  
Oliver J. Pountney ◽  
Mike Wilson ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Experimental Measurements ◽  
Pressure Measurements ◽  
Turbine Stage ◽  
Research Facility ◽  
Three Dimensional Flow ◽  
Co2 Gas ◽  
Performance Limit ◽  
Gas Concentration ◽  
Hot Gas

This paper describes experimental results from a research facility which experimentally models hot gas ingress into the wheel-space of an axial turbine stage. Measurements of CO2 gas concentration in the rim-seal region and inside the wheel-space are used to assess the performance of generic (though engine-representative) single and double seals in terms of the variation of concentration effectiveness with sealing flow rate. The variation of pressure in the turbine annulus, which governs externally-induced ingress, was obtained from steady pressure measurements downstream of the vanes. The benefit of using double seals is demonstrated: the ingested gas is shown to be predominately confined to the outer wheel-space radially outward of the inner seal; in the inner wheel-space, radially inward of the inner seal, the effectiveness is shown to be significantly higher. Criteria for ranking the performance of single and double seals are proposed, and the performance limit for any double seal is shown to be one in which the inner seal is exposed to rotationally-induced ingress. Although the ingress is a consequence of an unsteady, three-dimensional flow field and the cause-effect relationship between pressure and the sealing effectiveness is complex, the experimental data is shown to be successfully calculated by simple effectiveness equations developed from a theoretical model. The data illustrate that, for similar turbine-stage velocity triangles, the effectiveness can be correlated using two empirical parameters. In principle, these correlations could be extrapolated to a geometrically-similar turbine operating at engine-representative conditions.

Performance of a Finned Turbine Rim Seal

2014 ◽  
Author(s):  
Carl M. Sangan ◽  
James A. Scobie ◽  
J. Michael Owen ◽  
Gary D. Lock ◽  
Kok Mun Tham ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Turbine Stage ◽  
Research Facility ◽  
Flow Rates ◽  
Co2 Gas ◽  
Gas Concentration ◽  
Solid Body Rotation ◽  
Turbine Disc ◽  
Purge Flow ◽  
Improved Performance

In gas turbines, rim seals are fitted at the periphery of the wheel-space between the turbine disc and its adjacent casing; their purpose is to reduce the ingress of hot mainstream gases. A superposed sealant flow, bled from the compressor, is used to purge the wheel-space or at least dilute the ingress to an acceptable level. The ingress is caused by the circumferential variation of pressure in the turbine annulus radially outward of the seal. Engine designers often use double rim seals where the variation in pressure is attenuated in the outer wheel-space between the two seals. This paper describes experimental results from a research facility which models an axial turbine stage with engine-representative rim seals. The radial variation of CO2 gas concentration, swirl and pressure, in both the inner and outer wheel-space, are presented over a range of purge flow rates. The data are used to assess the performance of two seals: a datum double-rim seal and a derivative with a series of radial fins. The concept behind the finned seal is that the radial fins increase the swirl in the outer wheel-space; measurements of swirl show the captive fluid between the fins rotate with near solid body rotation. The improved attenuation of the pressure asymmetry, which governs the ingress, results in an improved performance of the inner geometry of the seal. The fins also increased the pressure in the outer wheel-space and reduced the ingress though the outer geometry of the seal.

Performance of a Finned Turbine Rim Seal

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Carl M. Sangan ◽  
James A. Scobie ◽  
J. Michael Owen ◽  
Gary D. Lock ◽  
Kok Mun Tham ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Turbine Disk ◽  
Turbine Stage ◽  
Research Facility ◽  
Flow Rates ◽  
Co2 Gas ◽  
Gas Concentration ◽  
Solid Body Rotation ◽  
Purge Flow ◽  
Improved Performance

In gas turbines, rim seals are fitted at the periphery of the wheel-space between the turbine disk and its adjacent casing; their purpose is to reduce the ingress of hot mainstream gases. A superposed sealant flow, bled from the compressor, is used to purge the wheel-space or at least dilute the ingress to an acceptable level. The ingress is caused by the circumferential variation of pressure in the turbine annulus radially outward of the seal. Engine designers often use double-rim seals where the variation in pressure is attenuated in the outer wheel-space between the two seals. This paper describes experimental results from a research facility that models an axial turbine stage with engine-representative rim seals. The radial variation of CO2 gas concentration, swirl, and pressure, in both the inner and outer wheel-space, are presented over a range of purge flow rates. The data are used to assess the performance of two seals: a datum double-rim seal and a derivative with a series of radial fins. The concept behind the finned seal is that the radial fins increase the swirl in the outer wheel-space; measurements of swirl show the captive fluid between the fins rotate with near solid body rotation. The improved attenuation of the pressure asymmetry, which governs the ingress, results in an improved performance of the inner geometry of the seal. The fins also increased the pressure in the outer wheel-space and reduced the ingress though the outer geometry of the seal.

Effect of Ingestion on Temperature of Turbine Discs

2012 ◽  
Author(s):  
Oliver J. Pountney ◽  
Carl M. Sangan ◽  
Gary D. Lock ◽  
J. Michael Owen
Keyword(s):  
Heat Transfer ◽  
Flow Rate ◽  
Thermochromic Liquid Crystal ◽  
Turbine Stage ◽  
Rotating Disc ◽  
Hot Gas ◽  
Nusselt Numbers ◽  
Adiabatic Effectiveness ◽  
Axial Clearance ◽  
First Time

This paper describes experimental results from a research facility which experimentally models hot-gas ingress into the wheel-space of an axial turbine stage with an axial-clearance rim seal. Thermochromic liquid crystal (TLC) was used to determine the effect of ingestion on heat transfer to the rotating disc; as far as the authors are aware, this is the first time that the measured effects of ingestion on adiabatic temperature have been published. An adiabatic effectiveness for the rotor was defined, and this definition was used to determine when the effect of ingress was first experienced by the rotor. Concentration measurements on the stator were used to determine the sealing effectiveness of the rim seal, and transient heat transfer tests with heated sealing air were used to determine the adiabatic effectiveness of the rotor. The thermal buffer ratio, which is defined as the ratio of the sealing flow rate when ingress first occurs to that when it is first experienced by the rotor, was shown to depend on the turbulent flow parameter. The local Nusselt numbers, Nu, which were measured on the rotor, were significantly smaller than those for a free disc; they decreased as the sealing flow rate decreased and as the ingress correspondingly increased. The values of Nu and adiabatic effectiveness obtained in these experiments provide data for the validation of CFD codes but caution is needed if they (particularly the values of Nu) are to be extrapolated to engine conditions.

Ingestion Into the Upstream Wheelspace of an Axial Turbine Stage

1994 ◽  
Vol 116 (2) ◽  
pp. 327-332 ◽  
Author(s):  
T. Green ◽  
A. B. Turner
Keyword(s):  
Pressure Distribution ◽  
Static Pressure ◽  
Three Dimensional ◽  
Computer Code ◽  
Rotor Blades ◽  
Rotor Speed ◽  
Turbine Stage ◽  
Flow Rates ◽  
Static Pressure Distribution ◽  
Axial Clearance

The upstream wheelspace of an axial air turbine stage complete with nozzle guide vanes (NGVs) and rotor blades (430 mm mean diameter) has been tested with the objective of examining the combined effect of NGVs and rotor blades on the level of mainstream ingestion for different seal flow rates. A simple axial clearance seal was used with the rotor spun up to 6650 rpm by drawing air through it from atmospheric pressure with a large centrifugal compressor. The effect of rotational speed was examined for several constant mainstream flow rates by controlling the rotor speed with an air brake. The circumferential variation in hub static pressure was measured at the trailing edge of the NGVs upstream of the seal gap and was found to affect ingestion significantly. The hub static pressure distribution on the rotor blade leading edges was rotor speed dependent and could not be measured in the experiments. The Denton three-dimensional C.F.D. computer code was used to predict the smoothed time-dependent pressure field for the rotor together with the pressure distribution downstream of the NGVs. The level and distribution of mainstream ingestion, and thus the seal effectiveness, was determined from nitrous oxide gas concentration measurements and related to static pressure measurements made throughout the wheelspace. With the axial clearance rim seal close to the rotor the presence of the blades had a complex effect. Rotor blades in connection with NGVs were found to reduce mainstream ingestion seal flow rates significantly, but a small level of ingestion existed even for very high levels of seal flow rate.

Sign in / Sign up

Export Citation Format

Share Document