Penetration of Elliptical Liquid Jets in Low-Speed Crossflow

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
M. R. Morad ◽  
H. Khosrobeygi
Keyword(s):  
Theoretical Model ◽  
Outer Boundary ◽  
Reynolds Numbers ◽  
Liquid Column ◽  
Empirical Correlation ◽  
Liquid Jets ◽  
Trajectory Prediction ◽  
Momentum Ratio ◽  
Low Speed ◽  
Aspect Ratios

Trajectory and penetration of elliptical liquid jets emerged into a low-speed crossflow of air are studied. The jets are introduced to the crossflow at different momentum ratios ranging from 1 to 300. The images are analyzed to obtain the trajectories of the outer boundary of the jets for two different aspect ratios. An empirical correlation is proposed for the present injector geometries and for the range of momentum ratio, Weber, and Reynolds numbers used in this study. Finally, a theoretical model for the trajectory of the liquid column for an initially elliptical liquid emerging into a crossflow is presented, and the associated drag coefficients are obtained for a precise trajectory prediction.

Heat Transfer for High Aspect Ratio Rectangular Channels in a Stationary Serpentine Passage With Turbulated and Smooth Surfaces

2013 ◽  
Author(s):  
Matthew A. Smith ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Aspect Ratio ◽  
Flow Behavior ◽  
Reynolds Numbers ◽  
Hydraulic Diameter ◽  
Internal Cooling ◽  
Number Range ◽  
Aspect Ratios ◽  
Parallel Configuration

Heat transfer distributions are presented for a stationary three passage serpentine internal cooling channel for a range of engine representative Reynolds numbers. The spacing between the sidewalls of the serpentine passage is fixed and the aspect ratio (AR) is adjusted to 1:1, 1:2, and 1:6 by changing the distance between the top and bottom walls. Data are presented for aspect ratios of 1:1 and 1:6 for smooth passage walls and for aspect ratios of 1:1, 1:2, and 1:6 for passages with two surfaces turbulated. For the turbulated cases, turbulators skewed 45° to the flow are installed on the top and bottom walls. The square turbulators are arranged in an offset parallel configuration with a fixed rib pitch-to-height ratio (P/e) of 10 and a rib height-to-hydraulic diameter ratio (e/Dh) range of 0.100 to 0.058 for AR 1:1 to 1:6, respectively. The experiments span a Reynolds number range of 4,000 to 130,000 based on the passage hydraulic diameter. While this experiment utilizes a basic layout similar to previous research, it is the first to run an aspect ratio as large as 1:6, and it also pushes the Reynolds number to higher values than were previously available for the 1:2 aspect ratio. The results demonstrate that while the normalized Nusselt number for the AR 1:2 configuration changes linearly with Reynolds number up to 130,000, there is a significant change in flow behavior between Re = 25,000 and Re = 50,000 for the aspect ratio 1:6 case. This suggests that while it may be possible to interpolate between points for different flow conditions, each geometric configuration must be investigated independently. The results show the highest heat transfer and the greatest heat transfer enhancement are obtained with the AR 1:6 configuration due to greater secondary flow development for both the smooth and turbulated cases. This enhancement was particularly notable for the AR 1:6 case for Reynolds numbers at or above 50,000.

Consistent Theoretical Model of Mean Diameter and Size Distribution by Liquid Sheet Atomization

2012 ◽  
Author(s):  
Chihiro Inoue ◽  
Toshinori Watanabe ◽  
Takehiro Himeno ◽  
Seiji Uzawa ◽  
Mitsuo Koshi
Keyword(s):  
Theoretical Model ◽  
Kinetic Energy ◽  
Droplet Diameter ◽  
Velocity Profiles ◽  
Liquid Sheet ◽  
Estimation Methods ◽  
Liquid Jets ◽  
Injection Velocity ◽  
Size Distributions ◽  
Mean Diameter

A consistent theoretical model is proposed and validated for calculating droplet diameters and size distributions. The model is derived based on the energy conservation law including the surface free energy and the Laplace pressure. Under several hypotheses, the law derives an equation indicating that atomization results from kinetic energy loss. Thus, once the amount of loss is determined, the droplet diameter is able to be calculated without the use of experimental parameters. When the effects of ambient gas are negligible, injection velocity profiles of liquid jets are the essential cause of the reduction of kinetic energy. The minimum Sauter mean diameter produced by liquid sheet atomization is inversely proportional to the injection Weber number when the injection velocity profiles are laminar or turbulent. A non-dimensional distribution function is also derived from the mean diameter model and Nukiyama-Tanasawa’s function. The new estimation methods are favorably validated by comparing with corresponding mean diameters and the size distributions, which are experimentally measured under atmospheric pressure.

Power Augmentation of a HAWT by Mie-type Tip Vanes, considering Wind Tunnel Flow Visualisation, Blade-Aspect Ratios and Reynolds Number

2003 ◽  
Vol 27 (3) ◽  
pp. 183-194 ◽  
Author(s):  
Yukimaru Shimizu ◽  
Edmond Ismaili ◽  
Yasunari Kamada ◽  
Takao Maeda
Keyword(s):  
Reynolds Number ◽  
Wind Tunnel ◽  
Aspect Ratio ◽  
Reynolds Numbers ◽  
Flow Visualisation ◽  
Velocity Measurements ◽  
Horizontal Axis Wind Turbine ◽  
Aspect Ratios ◽  
Detailed Surface ◽  
Blade Tips

Wind tunnel results are reported concerning the effects of blade aspect ratio and Reynolds number on the performance of a horizontal axis wind turbine (HAWT) with Mie-type1 tip attachments. The flow behaviour around the blade tips and the Mie-type tip vanes is presented. Detailed surface oil film visualization and velocity measurements around the blade tips, with and without Mie vanes, were obtained with the two-dimensional, Laser-Doppler Velocimetry method. Experiments were performed with rotors having blades with different aspect ratio and operating at different Reynolds numbers. The properties of the vortices generated by the Mie vanes and the blade tips were carefully studied. It was found that increased power augmentation by Mie vanes is achieved with blades having smaller aspect ratio and smaller Reynolds number.

Effect of Surface Roughness on Gaseous Flow Through Microchannels

2000 ◽  
Author(s):  
Stephen E. Turner ◽  
Hongwei Sun ◽  
Mohammad Faghri ◽  
Otto J. Gregory
Keyword(s):  
Surface Roughness ◽  
Reynolds Number ◽  
Friction Factor ◽  
Reynolds Numbers ◽  
Helium Flow ◽  
Local Pressure ◽  
Aspect Ratios ◽  
Corrugated Surfaces ◽  
Flow Through ◽  
Effect Of Surface

Abstract This paper presents an experimental investigation on nitrogen and helium flow through microchannels etched in silicon with hydraulic diameters between 10 and 40 microns, and Reynolds numbers ranging from 0.3 to 600. The objectives of this research are (1) to fabricate microchannels with uniform surface roughness and local pressure measurement; (2) to determine the friction factor within the locally fully developed region of the microchannel; and (3) to evaluate the effect of surface roughness on momentum transfer by comparison with smooth microchannels. The friction factor results are presented as the product of friction factor and Reynolds number plotted against Reynolds number. The following conclusions have been reached in the present investigation: (1) microchannels with uniform corrugated surfaces can be fabricated using standard photolithographic processes; and (2) surface features with low aspect ratios of height to width have little effect on the friction factor for laminar flow in microchannels.

scholarly journals Breakup of the Water Sheet Formed by Two Liquid Impinging Jets

2019 ◽  
Vol 2019 ◽  
pp. 1-8
Author(s):  
Yakang Xia ◽  
Lyes Khezzar ◽  
Shrinivas Bojanampati ◽  
Arman Molki
Keyword(s):  
Weber Number ◽  
Reynolds Numbers ◽  
Impinging Jets ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Impingement Angle ◽  
Number Range ◽  
Breakup Length ◽  
Sheet Breakup ◽  
Visualization Experiments

Flow visualization experiments are carried out to study the flow regimes and breakup length of the water sheet generated by two impinging liquid jets from an atomizer made of two identical tubes 0.686 mm in diameter. These experiments cover liquid jet Reynolds numbers based on the pipe diameter in the range of 1541 to 5394. The effects of the jet velocities and impingement angle between the two jets on the breakup performance are studied. Four spray patterns are recognized, which are presheet formation, smooth sheet, ruffled sheet, and open-rim sheet regimes. Water sheet breakup length is found to be consistent with previous experimental and theoretical results in the lower Weber number (based on water jet diameter and velocity) range. In the relatively high Weber number range, the breakup length tends to a constant value with increasing Weber number, and some discrepancies between experimental and theoretical predictions do exist. Measured water sheet area increases with increasing liquid jet Reynolds numbers and impingement angle within the range of the current study.

Topology of vortex breakdown in closed polygonal containers

2017 ◽  
Vol 820 ◽  
pp. 263-283 ◽  
Author(s):  
Igor V. Naumov ◽  
Irina Yu. Podolskaya
Keyword(s):  
Aspect Ratio ◽  
Cross Section ◽  
Vortex Breakdown ◽  
Laser Doppler Anemometry ◽  
Reynolds Numbers ◽  
Cylindrical Container ◽  
Stagnation Points ◽  
Aspect Ratios ◽  
Particle Visualization ◽  
Cross Section Geometry

The topology of vortex breakdown in the confined flow generated by a rotating lid in a closed container with a polygonal cross-section geometry has been analysed experimentally and numerically for different height/radius aspect ratios $h$ from 0.5 to 3.0. The locations of stagnation points of the breakdown bubble emergence and corresponding Reynolds numbers were determined experimentally and numerically by STAR-CCM+ computational fluid dynamics software for square, pentagonal, hexagonal and octagonal cross-section configurations. The flow pattern and velocity were observed and measured by combining seeding particle visualization and laser Doppler anemometry. The vortex breakdown size and position on the container axis were identified for Reynolds numbers ranging from 500 to 2800 in steady flow conditions. The obtained results were compared with the flow structure in the closed cylindrical container. The results allowed revealing regularities of formation of the vortex breakdown bubble depending on $Re$ and $h$ and the cross-section geometry of the confined container. It was found in a diagram of $Re$ versus $h$ that reducing the number of cross-section angles from eight to four shifts the breakdown bubble location to higher Reynolds numbers and a smaller aspect ratio. The vortex breakdown bubble area for octagonal cross-section was detected to correspond to the one for the cylindrical container but these areas for square and cylindrical containers do not overlap in the entire range of aspect ratio.

Flow Characteristics of Rectangular Liquid Jets Injected Into Low Subsonic Crossflow

2019 ◽  
Author(s):  
M. Tadjfar ◽  
A. Jaberi ◽  
R. Shokri
Keyword(s):  
High Speed ◽  
Flow Characteristics ◽  
Combustion Efficiency ◽  
Liquid Jets ◽  
High Speed Photography ◽  
Aspect Ratios ◽  
Jet Trajectory ◽  
Wide Range ◽  
Circular Holes ◽  
Subsonic Crossflow

Abstract Perpendicular injection of liquid jets into gaseous crossflow is well-known as an effective way to obtain good mixing between liquid fuel and air crossflow. Mostly, injectors with circular holes were used as the standard method of fuel spraying. However, recently a great attention to injectors with non-circular holes has emerged that aims to improve the quality of fuel mixing and consequently combustion efficiency. In the present work, rectangular injectors with different aspect ratios varying from 1 to 4 were experimentally studied. Using a wind tunnel with maximum air velocity of 42 m/s, tests were performed for a wide range of flow conditions including liquid-to-air momentum ratios of 10, 20, 30 and 40. Backlight shadowgraphy and high speed photography were employed to capture the instantaneous physics of the liquid jets discharged into gaseous crossflow. The flow physics of the rectangular liquid jets were investigated by means of flow visualizations. Different regimes of flow breakup including capillary, arcade, bag and multimode were observed for rectangular jets. Moreover, a new technique was used to calculate the trajectory of the liquid jets. It was shown the nozzle’s shape has no significant effect on jet trajectory. Also, the momentum ratio was found to has a profound effect on jet trajectory.

Detailed Flow Analysis Around Blade Tip With a Mie Vane in Case of Different Blade Aspect Ratios and Different Reynolds Numbers

2003 ◽  
Author(s):  
Yukimaru Shimizu ◽  
Edmond Ismaili ◽  
Yasunari Kamada ◽  
Takao Maeda
Keyword(s):  
Reynolds Number ◽  
Research Work ◽  
Flow Analysis ◽  
Reynolds Numbers ◽  
Power Coefficient ◽  
Work Related ◽  
Aspect Ratios ◽  
Power Increase ◽  
Lower Reynolds Number ◽  
Blade Tip

The results of an extensive experimental research work related to the performance of a HAWT with a tip-mounted Mie type vane are presented in this paper. From performance experiments carried out on four sets of blades with varying aspect ratios and for different Reynolds number, it was found that the application of a tip-mounted Mie vane resulted in a larger increase in maximum power coefficient for rotors with smaller aspect ratio and for lower Reynolds number. To investigate further the phenomenon and to explain the relationships found between power increase due to a Mie vane and blade aspect ratios and Reynolds number, detailed flow visualization around blade tip and the Mie vane were performed. It was found that the tendency of the power increase due to a Mie vane was dependent on the size of a corner vortex between blade tip and the downstream extension of the Mie vane.

Comparative study on interfacial oscillations of rectangular and elliptical liquid jets

2020 ◽  
Vol 234 (7) ◽  
pp. 1272-1286 ◽  
Author(s):  
Amin Jaberi ◽  
Mehran Tadjfar
Keyword(s):  
Aspect Ratio ◽  
Weber Number ◽  
High Speed ◽  
Nozzle Geometry ◽  
Liquid Jets ◽  
High Speed Photography ◽  
Aspect Ratios ◽  
Water Jets ◽  
Switching Phenomenon ◽  
Axis Switching

The instability characteristics and flow structures of water jets injected from rectangular and elliptical nozzles with aspect ratios varying from 2 to 6 were experimentally studied and compared. Shadowgraph technique was employed for flow visualization, and structures on the liquid jet surface were captured using high speed photography. It was found that disturbances originating from the nozzle geometry initially perturbed the liquid column, and then, at high jet velocities, disturbances generated within the flow dominated the jet surface. It was also found that rectangular nozzles introduced more disturbances into the flow than the elliptical ones. The characteristic parameters of axis-switching phenomenon including wavelength, frequency, and amplitude were measured and compared. Axis-switching wavelength was found to increase linearly with Weber number. Also, the wavelengths of rectangular jets were longer than the elliptical jets. Further, the frequency of axis-switching was shown to be reduced with increase of both Weber number and aspect ratio. It was observed that the axis-switching amplitude increased monotonically, reached a peak, and then decreased gradually. It was also found that the axis-switching amplitude varied with Weber number. At lower values of Weber number, the rectangular nozzles had higher amplitude than the elliptical nozzles. However, at higher values of Weber number, this relation was reversed, and the elliptical nozzles had the higher axis-switching amplitudes. This reversal Weber number decreased with the orifice aspect ratio. The reversal Weber number for aspect ratio of 4 was about 289, and it had decreased to 144 for the aspect ratio of 6.

Sign in / Sign up

Export Citation Format

Share Document