Rotating Corrected-Based Cavitation Model for a Centrifugal Pump

2018 ◽  
Vol 140 (11) ◽  
Author(s):  
Wang Jian ◽  
Wang Yong ◽  
Liu Houlin ◽  
Si Qiaorui ◽  
Matevž Dular
Keyword(s):  
Centrifugal Pump ◽  
Maximum Flow ◽  
Cavitation Model ◽  
Risk Area ◽  
Erosion Risk ◽  
Hydraulic Machinery ◽  
Cavity Structure ◽  
Pump Head ◽  
Motion Characteristic ◽  
Empirical Coefficients

Cavitation has bothered the hydraulic machinery for centuries, especially in pumps. It is essential to establish a solid way to predict the unsteady cavitation evolution with considerable accuracy. A novel cavitation model was proposed, considering the rotating motion characteristic of centrifugal pump. Comparisons were made with three other cavitation models and validated by experiments. Considerable agreements can be noticed between simulations and tests. All cavitation models employed have similar performance on predicting the pump head drop curve with proper empirical coefficients, and also the unsteady cavitation evolution was well solved. The proposed rotating corrected-based cavitation model (rotating based Zwart-Gerber-Belamri (RZGB)) obtained identical triangle cavity structure with the experiment visualizations, while the others also got triangle structure but with opposite direction. The maximum flow velocity in the impeller passage appears near the shroud, contributing to the typical triangle cavity structure. A preprocessed method for instant rotating images was carried out for evaluating the erosion risk area in centrifugal pump, based on the standard deviation of gray level. The results imply that the unsteady rear part of the attached cavity is vulnerable to be damaged, where the re-entrant flow was noticed. This work presented a suitable cavitation model and reliable numerical simulation approach for predicting cavitating flows in centrifugal pump.

Effect of Surfactant Additives on Centrifugal Pump Performance

2003 ◽  
Author(s):  
Satoshi Ogata ◽  
Keizo Watanabe ◽  
Asano Kimura
Keyword(s):  
Centrifugal Pump ◽  
Surfactant Concentration ◽  
Tap Water ◽  
Maximum Flow ◽  
Pump Efficiency ◽  
Optimal Temperature ◽  
Pump Performance ◽  
Surfactant Solutions ◽  
Pump Head ◽  
Shaft Power

Performance of a centrifugal pump when handling surfactant solutions was measured experimentally. The effects of the concentration and temperature of surfactant solutions on pump performance were investigated. It was clarified that the pump efficiency with surfactant solutions was higher than that with tap water, and increased with an increase of surfactant concentration. The value of maximum flow rate of the pump also increased. The total pump head increased with an increase in the surfactant concentration, however, the shaft power decreased with a decrease in the rotational speed of the impeller. The pump efficiency is dependent on the surfactant temperature, and there is an optimal temperature which maximizes the efficiency.

Modeling Viscous Oil Cavitating Flow in a Centrifugal Pump

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Wen-Guang Li
Keyword(s):  
Centrifugal Pump ◽  
Volume Ratio ◽  
Cavitating Flow ◽  
Liquid Volume ◽  
Cavitation Model ◽  
Gas Concentration ◽  
Noncondensable Gas ◽  
Cavitation Performance ◽  
Pump Head ◽  
Cfd Method

Properly modeling cavitating flow in a centrifugal pump is a very important issue for prediction of cavitation performance in pump hydraulic design optimization and application. As a first trial, the issue is explored by using computational fluid dynamics (CFD) method plus the full cavitation model herein. To secure a smoothed head-net positive suction head available (NPSHa) curve, several critical techniques are adopted. The cavitation model is validated against the experimental data in literature. The predicted net positive suction head required (NPSHr) correction factor for viscosity oils is compared with the existing measured data and empirical correlation curve, and the factor is correlated to impeller Reynolds number quantitatively. A useful relation between the pump head coefficient and vapor plus noncondensable gas-to-liquid volume ratio in the impeller is obtained. Vapor and noncondensable gas concentration profiles are illustrated in the impeller, and a “pseudocavitation” effect is confirmed as NPSHa is reduced. The effects of exit blade angle on NPSHr are presented, and the contributions of liquid viscosity and noncondensable gas concentration to the increase of NPSHr at a higher viscosity are identified.

Effect of Surfactant Additives on Centrifugal Pump Performance

2005 ◽  
Vol 128 (4) ◽  
pp. 794-798 ◽  
Author(s):  
Satoshi Ogata ◽  
Asano Kimura ◽  
Keizo Watanabe
Keyword(s):  
Centrifugal Pump ◽  
Energy Savings ◽  
Tap Water ◽  
Maximum Flow ◽  
Pipeline System ◽  
Pump Efficiency ◽  
Rotating Speed ◽  
Surfactant Solutions ◽  
Pump Head ◽  
Shaft Power

Performance of a centrifugal pump when handling surfactant solutions was measured experimentally. It was clarified that the pump efficiency with surfactant solutions was higher than that with tap water and increased with an increase in surfactant concentration. The value of maximum flow rate also increased. The total pump head increased with an increase in concentration, and the shaft power decreased with a decrease in the impeller rotating speed. There was an optimal temperature, which maximizes the efficiency. By combining the data for the piping section and for the pump efficiency, it is possible to accurately predict the energy savings of the pumping power in the pipeline system.

Effect of semi-open impeller side clearance on centrifugal pump cavitation inception

2018 ◽  
Vol 1 (2) ◽  
pp. 24-39
Author(s):  
A. Farid ◽  
A. Abou El-Azm Aly ◽  
H. Abdallah
Keyword(s):  
Centrifugal Pump ◽  
Static Pressure ◽  
Rotation Speed ◽  
Centrifugal Pumps ◽  
Severe Condition ◽  
Cavitation Inception ◽  
Total Input ◽  
Input Pressure ◽  
Pump Head ◽  
Pump Pressure

Cavitation in pumps is the most severe condition that centrifugal pumps can work in and is leading to a loss in their performance.  Herein, the effect of semi-open centrifugal pump side clearance on the inception of pump cavitation has been investigated.  The input pump pressure has been changed from 80 to 16 kPa and the pump side clearance has been changed from 1 mm to 3 mm at a rotation speed of 1500 rpm. It has been shown that as the total input pressure decreased; the static pressure inside the impeller is reduced while the total pressure in streamwise direction has been reduced, also the pump head is constant with the reduction of the total input pressure until the cavitation is reached. Head is reduced due to cavitation inception; the head is reduced in the case of a closed impeller with a percent of 1.5% while it is reduced with a percent of 0.5% for pump side clearance of 1mm, both are at a pressure of 20 kPa.   Results also showed that the cavitation inception in the pump had been affected and delayed with the increase of the pump side clearance; the cavitation has been noticed to occur at approximate pressures of 20 kPa for side clearance of 1mm, 18 kPa for side clearances of 2mm and 16 kPa for 3mm.

scholarly journals Assessment of Soil Erosion and Its Impact on Agricultural Productivity by Using the RMMF Model and Local Perception: A Case Study of Rangun Watershed of Mid-Hills, Nepal

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Dinesh Bhandari ◽  
Rajeev Joshi ◽  
Raju Raj Regmi ◽  
Nripesh Awasthi
Keyword(s):  
Soil Erosion ◽  
Soil Loss ◽  
Group Discussion ◽  
Agricultural Productivity ◽  
Weighted Mean ◽  
Risk Area ◽  
Barren Land ◽  
Erosion Risk ◽  
Risk Areas ◽  
The Impact

Soil erosion is a major concern for the environment and natural resources leading to a serious threat to agricultural productivity and one of the major causes of land degradation in the mid-hills region of Nepal. An accurate assessment of soil erosion is needed to reduce the problem of soil loss in highly fragile mountainous areas. The present study aimed to assess spatial soil loss rate and identified risk areas and their perceived impact on agricultural productivity by using the Revised Morgan–Morgan–Finney (RMMF) model and social survey in the Rangun watershed of Dadeldhura district, Nepal. Soil erosion was assessed by using data on soil, digital elevation model, rainfall, land use, and land cover visually interpreted from multitemporal satellite images, and ILWIS 3.3 academic software was used to perform the model. A household questionnaire survey (n = 120) and focus group discussion (n = 2) in identified risk areas were carried out to understand the people’s perception towards soil erosion and its impact on agricultural productivity. The predicted average soil erosions from the forest, agriculture, and barren land were 2.7 t ha−1 yr−1, 53.73 t ha−1 yr−1, and 462.59 t ha−1 yr−1, respectively. The erosion risk area under very low to low, moderate to moderately high, and high to very high covers 92.32%, 4.96%, and 2.73%, respectively. It indicates that the rate of soil erosion was lower in forest areas, whereas it was higher in the barren land. The cropped area of the watershed has been reduced by 2.96 ha−1 yr−1, and productivity has been decreased by 0.238 t ha−1 yr−1. The impacts such as removal of topsoil (weighted mean = 4.19) and gully formation (weighted mean = 3.56) were the highest perceived factors causing productivity decline due to erosion. People perceived the impact of erosion in agricultural productivity differently ( ∗ significant at P ≤ 0.05 ). The study concluded that, comparatively, barren and agricultural lands seem more susceptible to erosion, so the long-term conservation and management investment in susceptible areas for restoration, protection, and socioeconomic support contribute significantly to land rehabilitation in the Rangun watershed.

scholarly journals ANALISA PERHITUNGAN DAYA POMPA SENTRIFUGAL DI GEDUNG UNIVERSITAS 17AGUSTUS 1945 JAKARTA

2019 ◽  
Vol 4 (1) ◽  
pp. 7-14
Author(s):  
M Fajri Hidayat ◽  
Nor Fajri
Keyword(s):  
Pump Power ◽  
Centrifugal Pump ◽  
Water Requirement ◽  
Clean Water ◽  
Pump Head ◽  
Pump Shaft ◽  
Specific Speed

AbstrakPompa adalah suatu alat atau mesin untuk memindahkan cairan dari satu tempat ketempat lain melalui suatu media perpipaan dengan cara menambahkan energi pada cairan yang dipindahkan dan berlangsung secara terus menerus. Pompa yang digunakan dalam analisa ini yaitu Pompa Sentrifugal yang terdapat di gedung Universitas 17 Agustus 1945 Jakarta. Tujuan dari analisa ini yaitu untuk mengetahui kebutuhan air pada gedung Universitas 17 Agustus 1945 Jakarta. Kebutuhan air pada gedung Universitas 17 Agustus 1945 Jakarta dihitung berdasarkan luas lantai gedung dan pemakaian setiap dosen, karyawan, mahasiswa, dan rektorat di Universitas 17 Agustus 1945 Jakarta. Hasil analisa di dapatkan total kebutuhan air bersih pada gedung Universitas 17 Agustus 1945 Jakarta adalah 1.7910 Liter/hari. Kapasitas pompa sebesar 0.06 m3/s. Head total pompa sebesar 31.99 m. Putaran poros pompa yaitu 1500 rpm. Daya pompa sebesar 0.817 kW. Kecepatan spesifik sebesar 48.51 rpm. Dari hasil analisa dapat dinyatakan bahwa Pompa Sentrifugal yang berada di gedung Universitas 17 Agustus 1945 Jakarta sudah layak untuk digunakan. Kata Kunci : Kebutuhan air, kapasitas pompa, pompa sentrifugal Abstract          A pump is a device or a machine to move liquids from one place to another via a piping medium by adding energy to the fluid that is moved and continuous. The pump used in this analysis is the Centrifugal Pump contained in the building University 17 August 1945 Jakarta. The purpose of this analysis is to determine the needs of water in the building University 17 August 1945 Jakarta. Water requirement at University building August 17, 1945 Jakarta is calculated based on building floor and usage of every lecturer, staff, student, and rectorate in University 17 August 1945 Jakarta. The result of the analysis in obtaining the total clean water requirement at the building University 17 August 1945 Jakarta is 1.7910 Liter / day. The pump capacity is 0.06 m3 / s. The total pump head is 31.99 m. The rotation of the pump shaft is 1500 rpm. The pump power is 0.817 kW. Specific speed of 48.51 rpm. The results of the analysis can be stated that the Centrifugal Pump located in the building University 17 August 1945 Jakarta is feasible to use. Keywords : Water requirement, pump capacity, centrifugal pump

Numerical study of cavitating flow over hydrofoil in the presence of air

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Włodzimierz Wróblewski ◽  
Krzysztof Bochon ◽  
Mirosław Majkut ◽  
Krzysztof Rusin ◽  
Emad Hasani Malekshah
Keyword(s):  
Numerical Study ◽  
Cavitating Flow ◽  
Cavitation Model ◽  
Two Phase ◽  
Content Type ◽  
Flow Simulations ◽  
Cavity Structure ◽  
Dynamic Forces ◽  
High Dynamic ◽  
The Impact

Purpose The presence of air in the water flow over the hydrofoil is investigated. The examined hydrofoil is ClarkY 11.7% with an angle of attack of 8 deg. The flow simulations are performed with the assumption of different models. The Singhal cavitation model and the models which resolve the non-condensable gas including 2phases and 3phases are implemented in the numerical model. The calculations are performed with the uRANS model with assumption of the constant temperature of the mixture. The two-phase flow is simulated with a mixture model. The dynamics and structures of cavities are compared with literature data and experimental results. Design/methodology/approach The cavitation regime can be observed in some working conditions of turbomachines. The phase transition, which appears on the blades, is the source of high dynamic forces, noise and also can lead to the intensive erosion of the blade surfaces. The need to control this process and to prevent or reduce the undesirable effects can be fulfilled by the application of non-condensable gases to the liquid. Findings The results show that the Singhal cavitation model predicts the cavity structure and related characteristics differently with 2phases and 3phases models at low cavitation number where the cavitating flow is highly dynamic. On the other hand, the impact of dissolved air on the cloud structure and dynamic characteristic of cavitating flow is gently observable. Originality/value The originality of this paper is the evaluation of different numerical cavitation models for the prediction of dynamic characteristics of cavitating flow in the presence of air.

Performance characteristics of the new Eurosets magnetically suspended centrifugal pump

Perfusion ◽  
2020 ◽  
pp. 026765912093199
Author(s):  
Denis Berdajs ◽  
Ludwig K von Segesser ◽  
Francesco Maisano ◽  
Guiseppina Milano ◽  
Enrico Ferrari
Keyword(s):  
Centrifugal Pump ◽  
Repeated Measurements ◽  
Hydrodynamic Performance ◽  
Membrane Oxygenator ◽  
Mean Flow ◽  
Biochemical Tests ◽  
Extracorporeal Membrane Oxygenator ◽  
Pump Head ◽  
Ventricular Assistance Device ◽  
Magnetically Suspended Centrifugal Pump

Objective: The aim was to evaluate the performance of a newly developed magnetically suspended centrifugal pump head intended for use as a ventricular assistance device with a newly developed extracorporeal membrane oxygenator setup. Methods: In an experimental setup, an extracorporeal membrane oxygenator circuit was established in three calves with a mean weight of 68.2 ± 2.0 kg. A magnetically levitated centrifugal pump was tested, along with a newly designed extracorporeal membrane oxygenator console, at three different flow ranges: (a) 0.0 to 5.2 L/min, (b) 0.0 to 7.1 L/min, and (c) 0.0 to 6.0 L/min. For each setup, the animals were supported by a circuit for 6 h. Blood samples were collected just before caridiopulmonary bypass (CPB) after 10 min on bypass and after 1, 2, 5, and 6 h of perfusion for hemolysis determination and biochemical tests. Values were recorded for blood pressure, mean flow, and pump rotational speed. Analysis of variance was used for repeated measurements. Results: Mean pump flows achieved during the three 6 h pump runs for the three pump heads studied were as follows: (a) flow range 0.0 to 5.2 L/min, 3.6 ± 1.5 L/min, (b) flow range 0.0 to 7.1 L/min, 4.9 ± 1.3 L/min, and (c) flow range 0.0 to 6.0 L/min, 3.8 ± 1.5 L/min. Blood trauma, evaluated by plasma hemoglobin and lactate dehydrogenase levels, did not help in detecting any significant hemolysis. Thrombocytes and white blood cell count profiles showed no significant differences between the groups at the end of the 6 h perfusion. At the end of testing, no clot deposition was found in the oxygenator, and there was no evidence of peripheral emboli. Conclusion: The results suggest that the newly developed magnetically suspended centrifugal pump head provides satisfactory hydrodynamic performance in an acute perfusion scenario without increasing hemolysis.

Development of one-axis controlled bearingless motor and its application to a centrifugal pump for extremely low temperature

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1287-1294
Author(s):  
Hirohisa Kato ◽  
Mochimitsu Komori ◽  
Ken-ichi Asami ◽  
Nobuo Sakai
Keyword(s):  
Low Temperature ◽  
Centrifugal Pump ◽  
Liquid Nitrogen ◽  
Flow Rate ◽  
Maximum Flow ◽  
Magnetic Bearing ◽  
Lubricating Oil ◽  
Bearingless Motor ◽  
The Difference ◽  
Conventional Study

In this paper, a centrifugal pump for for extremely low temperature was fabricated and evaluated by experiments in liquid nitrogen. The pump is using a bearingless motor and permanent magnet bearings to levitate and rotate the rotor without lubricating oil. The difference from the conventional study is that a one-axis controlled bearingless motor is used to reduce the magnetic bearing cost and that the bearings are installed in the liquid to eliminate a shaft-seal. Stable levitation and rotation of the rotor were confirmed in the rotation and pump experiments in liquid nitrogen. In pump experiment, the flow rate of liquid nitrogen was measured at 1 cm in a pumping height. The maximum flow rate was 1.3 L/min when the rotation speed is 1,800 rpm.

Sign in / Sign up

Export Citation Format

Share Document