scholarly journals Gravity-Insensitive Flexure Pivot Oscillators

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
M. H. Kahrobaiyan ◽  
E. Thalmann ◽  
L. Rubbert ◽  
I. Vardi ◽  
S. Henein
Keyword(s):  
Rigid Body ◽  
Quality Factor ◽  
Plain Bearing ◽  
Drastic Reduction ◽  
Leaf Springs ◽  
Order Of Magnitude ◽  
Torsional Beam ◽  
The Cross ◽  
Long Stroke ◽  
Magnitude Increase

Classical mechanical watch plain bearing pivots have frictional losses limiting the quality factor of the hairspring-balance wheel oscillator. Replacement by flexure pivots leads to a drastic reduction in friction and an order of magnitude increase in quality factor. However, flexure pivots have drawbacks including gravity sensitivity, nonlinearity, and limited stroke. This paper analyzes these issues in the case of the cross-spring flexure pivot (CSFP) and presents an improved version addressing them. We first show that the cross-spring pivot cannot be simultaneously linear, insensitive to gravity, and have a long stroke: the 10 ppm accuracy required for mechanical watches holds independently of orientation with respect to gravity only when the leaf springs cross at 12.7% of their length. But in this case, the pivot is nonlinear and the stroke is only 30% of the symmetrical (50% crossing) cross-spring pivot's stroke. The symmetrical pivot is also unsatisfactory as its gravity sensitivity is of order 104 ppm. This paper introduces the codifferential concept which we show is gravity-insensitive. It is used to construct a gravity-insensitive flexure pivot (GIFP) consisting of a main rigid body, two codifferentials, and a torsional beam. We show that this novel pivot achieves linearity or the maximum stroke of symmetrical pivots while retaining gravity insensitivity.

scholarly journals Hydraulic transmissivity inferred from ice-sheet relaxation following Greenland supraglacial lake drainages

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Ching-Yao Lai ◽  
Laura A. Stevens ◽  
Danielle L. Chase ◽  
Timothy T. Creyts ◽  
Mark D. Behn ◽  
...  
Keyword(s):  
Laboratory Experiments ◽  
Ice Sheet ◽  
Drainage System ◽  
Greenland Ice Sheet ◽  
Field Observations ◽  
Surface Uplift ◽  
Drainage Networks ◽  
Order Of Magnitude ◽  
Lake Drainage ◽  
Magnitude Increase

AbstractSurface meltwater reaching the base of the Greenland Ice Sheet transits through drainage networks, modulating the flow of the ice sheet. Dye and gas-tracing studies conducted in the western margin sector of the ice sheet have directly observed drainage efficiency to evolve seasonally along the drainage pathway. However, the local evolution of drainage systems further inland, where ice thicknesses exceed 1000 m, remains largely unknown. Here, we infer drainage system transmissivity based on surface uplift relaxation following rapid lake drainage events. Combining field observations of five lake drainage events with a mathematical model and laboratory experiments, we show that the surface uplift decreases exponentially with time, as the water in the blister formed beneath the drained lake permeates through the subglacial drainage system. This deflation obeys a universal relaxation law with a timescale that reveals hydraulic transmissivity and indicates a two-order-of-magnitude increase in subglacial transmissivity (from 0.8 ± 0.3 $${\rm{m}}{{\rm{m}}}^{3}$$ m m 3 to 215 ± 90.2 $${\rm{m}}{{\rm{m}}}^{3}$$ m m 3 ) as the melt season progresses, suggesting significant changes in basal hydrology beneath the lakes driven by seasonal meltwater input.

scholarly journals Review of the soft-X-ray laser research at CEL-V

1991 ◽  
Vol 9 (2) ◽  
pp. 493-499
Author(s):  
D. Naccache ◽  
J-L. Bourgade ◽  
P. Combis ◽  
C. J. Keane ◽  
J-P. Le Breton ◽  
...  
Keyword(s):  
Atomic Number ◽  
Collisional Excitation ◽  
X Ray ◽  
Order Of Magnitude ◽  
Laser Experiments ◽  
Magnitude Increase

We present some significant results of collisional excitation X-ray laser experiments in plasmas produced by a laser. We studied the amplification in Ne- and Ni-like ions by varying both the nature and the thickness of targets, the irradiation, and the wavelength of the driving laser. Some potentially interesting scalings as a function of the atomic number of the lasing element are demonstrated in the Ne-like system. An order-of-magnitude increase in gain in the Ni-like experiments was determined.

ISOSPIN DECOMPOSITION OF pp → NNππ CROSS SECTIONS — DO WE SEE A SIGN OF Δ(1600) EXCITATION IN THE nnπ+π+ CHANNEL?

2009 ◽  
Vol 24 (02n03) ◽  
pp. 450-453
Author(s):  
◽  
T. SKORODKO ◽  
M. BASHKANOV ◽  
D. BOGOSLOWSKY ◽  
H. CALÉN ◽  
...  
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Differential Cross ◽  
Pion Production ◽  
Significant Contribution ◽  
Differential Cross Sections ◽  
Pp Collisions ◽  
Theoretical Predictions ◽  
Order Of Magnitude ◽  
The Cross

The two-pion production in pp-collisions has been investigated in exclusive measurements from threshold up to Tp = 1.36 GeV . Total and differential cross sections have been obtained for the channels pnπ+π0, ppπ+π-, ppπ0π0 and also nnπ+π+. For intermediate incident energies Tp > 1 GeV , i.e. in the region, which is beyond the Roper excitation but at the onset of ΔΔ excitation the total ppπ0π0 cross section falls behind theoretical predictions by as much as an order of magnitude near 1.2 GeV, whereas the nnπ+π+ cross section is a factor of five larger than predicted. A model-unconstrained isospin decompostion of the cross section points to a significant contribution of an isospin 3/2 resonance other than the Δ(1232). As a possible candidate the Δ(1600) is discussed.

Critical current density and microstructure variations in YBa2Cu3O7−x + BaSnO3 films with different concentrations of BaSnO3

2008 ◽  
Vol 23 (12) ◽  
pp. 3363-3369 ◽  
Author(s):  
C.V. Varanasi ◽  
J. Burke ◽  
L. Brunke ◽  
H. Wang ◽  
J.H. Lee ◽  
...  
Keyword(s):  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
Gradual Increase ◽  
Critical Transition ◽  
Critical Transition Temperature ◽  
Transmission Electron ◽  
Order Of Magnitude ◽  
High Fields ◽  
Magnitude Increase

Previous work on YBa2Cu3O7−x (YBCO) + BaSnO3 (BSO) films with a single composition showed significant critical current density (Jc) improvements at higher fields but lowered Jc in low fields. A detailed study on BSO concentrations provided here demonstrates that significant Jc enhancement can occur even up to 20 mol% BSO inclusion, where typical particulate inclusions in these concentrations degrade the YBCO performance. YBCO + BSO films were processed on (100) LaAlO3 substrates using premixed targets of YBa2Cu3O7-x (YBCO) with additions of 2, 4, 10, and 20 mol% BSO. The critical transition temperature Tc of the films remained high (>87 K), even with large amounts (20 mol%) of BSO. YBCO + BSO films showed a gradual increase in Jc at high fields as the amount of BSO was increased. More than an order of magnitude increase in Jc was measured in YBCO + BSO samples as compared to regular YBCO at 4 T. YBCO + 10 mol% BSO films showed overall improvement at all the field ranges while YBCO + 20 mol% BSO was better only at high fields. Transmission electron microscopy revealed the presence of ∼7–8-nm-diameter BSO nanocolumns, the density of which increased with increasing BSO content correlating well with the observed improvements in Jc.

scholarly journals Large-area printing of ferroelectric surface and super-domains for efficient solar water splitting

2020 ◽  
Author(s):  
Yu Tian ◽  
Yaqing Wei ◽  
Minghui Pei ◽  
Rongrong Cao ◽  
Zhenao Gu ◽  
...  
Keyword(s):  
Water Splitting ◽  
Electric Fields ◽  
Electronic Structures ◽  
Active Sites ◽  
Large Area ◽  
Solar Water Splitting ◽  
High Efficient ◽  
Catalytic Sites ◽  
Order Of Magnitude ◽  
Magnitude Increase

Abstract Surface electronic structures of the photoelectrodes determine the activity and efficiency of the photoelectrochemical water splitting, but the controls of their surface structures and interfacial chemical reactions remain challenging. Here, we use ferroelectric BiFeO3 as a model system to demonstrate an efficient and controllable water splitting reaction by large-area constructing the hydroxyls-bonded surface. The up-shift of band edge positions at this surface enables and enhances the interfacial holes and electrons transfer through the hydroxyl-active-sites, leading to simultaneously enhanced oxygen and hydrogen evolutions. Furthermore, printing of ferroelectric super-domains with microscale checkboard up/down electric fields separates the distribution of reduction/oxidation catalytic sites, enhancing the charge separation and giving rise to an order of magnitude increase of the photocurrent. This large-area printable ferroelectric surface and super-domains offer an alternative platform for controllable and high-efficient photocatalysis.

scholarly journals Hydrodechlorination of CHClF2 (HCFC-22) over Pd-Pt catalysts supported on thermally modified activated carbon. Beneficial effect of catalyst oxidation.

2021 ◽  
Author(s):  
Monika Radlik ◽  
Wojciech Juszczyk ◽  
Wioletta Raróg-Pilecka ◽  
Magdalena Zybert ◽  
Zbigniew Karpiński
Keyword(s):  
Alloy Composition ◽  
Active Surface ◽  
Metal Particles ◽  
Pt Catalysts ◽  
Modified Activated Carbon ◽  
Palladium Surface ◽  
Order Of Magnitude ◽  
Carbon Burning ◽  
Magnitude Increase ◽  
Catalyst Oxidation

Pd-Pt catalysts supported on carbon preheated to 1600°C have been reinvestigated in CHFCl2 hydrodechlorination. An additionally adopted catalyst oxidation at 350-400°C produced an order of magnitude increase in the catalytic activity of Pd/C. This increase is not caused by changes in metal dispersion or possible decontamination of the Pd surface from superficial carbon, but rather by unlocking the active surface, originally inaccessible in metal particles tightly packed in the pores of carbon. Burning carbon from the pore walls attached to the metal changes the pore structure, providing easier access for the reactants to the entire palladium surface. As upon calcination the performance of the rest of the Pd-Pt/C catalysts changes less than for Pd/C, the relation between the turnover frequency and alloy composition does not confirm the Pd-Pt synergy invoked in our previous work. The use of even higher-preheated carbon (1800°C), completely free of micropores, results in a Pd/C catalyst that does not need to be oxidized to achieve high activity and excellent selectivity up to CH2F2 (>90%).

scholarly journals Optbayesexpt: Sequential Bayesian Experiment Design for Adaptive Measurements

2021 ◽  
Vol 126 ◽  
Author(s):  
Robert D. McMichael ◽  
Sean M. Blakley ◽  
Sergey Dushenko
Keyword(s):  
Lower Cost ◽  
Adaptive Algorithms ◽  
Efficient Estimation ◽  
Function Parameter ◽  
Model Function ◽  
Measurement Results ◽  
Adaptive Measurements ◽  
Order Of Magnitude ◽  
Magnitude Increase ◽  
Python Package

Optbayesexpt is a public domain, open-source python package that provides adaptive algorithms for efficient estimation/measurement of parameters in a model function. Parameter estimation is the type of measurement one would conventionally tackle with a sequence of data acquisition steps followed by fitting. The software is designed to provide data-based control of experiments, effectively learning from incoming measurement results and using that information to select future measurement settings live and online as measurements progress. The settings are chosen to have the best chances of improving the measurement results. With these methods optbayesexpt is designed to increase the efficiency of a sequence of measurements, yielding better results and/or lower cost. In a recent experiment, optbayesexpt yielded an order of magnitude increase in speed for measurement of a few narrow peaks in a broad spectral range.

Gate-tunable ion–electron hybrid phototransistor based on a graphene/RbAg4I5 composite

2019 ◽  
Vol 7 (42) ◽  
pp. 13253-13260
Author(s):  
Pengfei Wang ◽  
Jun Yin ◽  
Qianqian Hu ◽  
Bocheng Lv ◽  
Jia-Lin Zhu ◽  
...  
Keyword(s):  
Binding Energy ◽  
Single Layer ◽  
Silver Ions ◽  
Single Layer Graphene ◽  
Layer Graphene ◽  
Order Of Magnitude ◽  
Photo Response ◽  
Magnitude Increase ◽  
Linear Modulation

A phototransistor based on a composite of single-layer graphene and superconductor RbAg4I5 realizes linear modulation of the binding energy between electrons and silver ions, resulting in a two order of magnitude increase of photo-response.

scholarly journals Seismic observations of crevasse growth following rain-induced glacier acceleration, Haupapa/Tasman Glacier, New Zealand

2019 ◽  
Vol 60 (79) ◽  
pp. 14-22
Author(s):  
Samuel Taylor-Offord ◽  
Huw Horgan ◽  
John Townend ◽  
J. Paul Winberry
Keyword(s):  
New Zealand ◽  
Strain Rate ◽  
Rain Rate ◽  
Ice Sheets ◽  
Seismic Events ◽  
Seismicity Rate ◽  
Acceleration Rate ◽  
Order Of Magnitude ◽  
Strain Rate Field ◽  
Magnitude Increase

ABSTRACTChanging rates of water input can affect both the flow of glaciers and ice sheets and their propensity to crevasse. Here we examine geodetic and seismic observations during two substantial (10–18-times background velocity) rain-induced glacier accelerations at Haupapa/Tasman Glacier, New Zealand. Changes in rain rate result in glacier acceleration and associated uplift, which propagate down-glacier. This pattern of acceleration results in a change to the strain rate field, which correlates with an order of magnitude increase in the apparent seismicity rate and an overall down-glacier migration in located seismicity. After each acceleration event the apparent seismicity rate decreases to below the pre-acceleration rate for 3 days. This suggests that seismic events associated with surface crevasse growth occur early during phases of glacier acceleration due to elevated extensional stresses, and then do not occur again until stresses recover.

Sign in / Sign up

Export Citation Format

Share Document