Experimental and Numerical Investigations of Closed Radial Inflow Turbine With Labyrinth Seals

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Wen Li ◽  
Xing Wang ◽  
Xuehui Zhang ◽  
Xinjing Zhang ◽  
Yangli Zhu ◽  
...  
Keyword(s):  
Small Volume ◽  
Labyrinth Seal ◽  
Volume Flow ◽  
Tip Clearance ◽  
Labyrinth Seals ◽  
Computation Result ◽  
Numerical Investigations ◽  
Clearance Flow ◽  
Computational Fluid Dynamics Cfd ◽  
Radial Inflow Turbine

It is a common practice to use closed impeller in radial inflow turbine against the flow leakage from tip clearance of impellers, especially in small volume flow condition. It utilizes labyrinths between the shroud and the case to abate the higher pressure leakage. Experimental and computational investigations of shroud clearance flow in a radial inflow turbine with labyrinth seals are presented in this paper. Compared with the result without leakage, numerical computation result including the leakage of labyrinth seals agrees better with that of the experiment result, which indicates that the leakage of labyrinth seals cannot be neglected. Several geometrical arrangements with a series of different clearance of labyrinth seals are investigated experimentally and numerically, and the dimensionless shroud clearance is of 0%, 0.6%, 1.2%, 1.8%, 2.7%, 3.6%. Finally, the character of flow and loss is analyzed by computational fluid dynamics (CFD) tools. The results indicate that the labyrinth seal flow has no effect on the main flow passage and mainly causes different leakage mass flow.

Numerical Investigations of Leakage Performance Degradations in Labyrinth and Flexible Seals Due to Wear

2020 ◽  
Author(s):  
Xinbo Dai ◽  
Xin Yan ◽  
Kun He ◽  
Jun Li ◽  
Zhenping Feng
Keyword(s):  
Labyrinth Seal ◽  
Leakage Rate ◽  
Labyrinth Seals ◽  
Element Analysis ◽  
Numerical Investigations ◽  
Forward Bending ◽  
The Finite Element Analysis ◽  
Before And After ◽  
Computational Fluid Dynamics Cfd ◽  
Wear Damage

Abstract The Finite Element Analysis (FEA) and Computational Fluid Dynamics (CFD) methods are utilized to investigate the leakage performance degradations in two kinds of flexible seals (i.e. forward bending and backward bending) and two kinds of shroud labyrinth seals (i.e. with straight fins and chamfered fins) in rubbing events. With the existing experimental data, FEA methods for contacting simulations and CFD methods for leakage rate and flow pattern predictions are carefully examined. The wear characteristic and leakage performance between labyrinth seals and flexible seals are compared before and after rub. The results show that, in rubbing process, the labyrinth seal with straight (symmetrical) fins is likely to undergo the mushrooming damage, whereas the labyrinth seal with chamfered (asymmetrical) fins is likely to undergo the tooth-bending damage. In rubbing process, compared with the labyrinth seal, the flexible seal has a superior characteristic in resisting the wear damage due to increased flexibility of fin. For a labyrinth seal with 0.3mm design clearance and a flexible seal with 0.15mm design clearance, the 0.5mm radial displacement of rotor will result in 110% increase of leakage rate for labyrinth seal, and 7% increase of leakage rate for flexible seal after wear. Under the same conditions, the forward bending flexible seal has a lower leakage rate than the backward bending flexible seal before and after rub.

scholarly journals Flow Field Investigation in the Exit Region of a Radial Inflow Turbine Using LDV

1994 ◽  
Author(s):  
D. Muthuvel Murugan ◽  
Widen Tabakoff ◽  
Awatef Hamed
Keyword(s):  
Flow Field ◽  
Field Investigation ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Complex Flow ◽  
Tip Clearance Flow ◽  
Exit Region ◽  
Flow Investigation ◽  
Clearance Flow ◽  
Radial Inflow Turbine

Detailed flow investigation in the downstream region of a radial inflow turbine has been performed using a three component Laser Doppler Velocimetry. The flow velocities are measured in the exit region of the turbine at off-design operating conditions. The results are presented as contour and vector plots of mean velocities, flow angles and turbulent stresses. The measured parameters are correlated to the rotor blade rotation to observe any periodic nature of the flow. The measurements reveal a complex flow pattern near the tip region at the rotor exit due to the interaction of the tip clearance flow. The degree of swirl of the flow near the tip region at the rotor exit is observed to be high due to the gross under turning of the flow near the tip region. The effect of the rotor on the exit flow field is observed in the proximity of the rotor exit.

Progressive Clearance Labyrinth Seal for Turbo-Machinery Applications

2011 ◽  
Author(s):  
Binayak Roy ◽  
Hrishikesh V. Deo ◽  
Xiaoqing Zheng
Keyword(s):  
Theoretical Models ◽  
Labyrinth Seal ◽  
Tip Clearance ◽  
Labyrinth Seals ◽  
Lower Efficiency ◽  
Thermal Transients ◽  
Low Leakage ◽  
Packing Ring ◽  
Lift Off ◽  
Large Rotor

Turbomachinery sealing is a challenging problem due to the varying clearances caused by thermal transients, vibrations, bearing lift-off etc. Leakage reduction has significant benefits in improving engine efficiency and reducing emissions. Conventional labyrinth seals have to be assembled with large clearances to avoid rubbing during large rotor transients. This results in large leakage and lower efficiency. In this paper, we propose a novel Progressive Clearance Labyrinth Seal that is capable of providing passive fluidic feedback forces that balance at a small tip-clearance. A modified packing ring is supported on flexures and employs progressively tighter teeth from the upstream to the downstream direction. When the tip-clearance reduces below the equilibrium clearance, fluidic feedback forces cause the packing ring to open. Conversely, when the tip-clearance increases above the equilibrium clearance, the fluidic feedback forces cause the packing ring to close. Due to this self-correcting behavior, the seal provides high differential pressure capability, low leakage and non-contact operation even in the presence of large rotor transients. Theoretical models for the feedback phenomenon have been developed and validated by experimental results.

Leakage and Cavity Pressures in an Interlocking Labyrinth Gas Seal: Measurements vs. Predictions

2019 ◽  
Author(s):  
Luis San Andrés ◽  
Tingcheng Wu ◽  
Jose Barajas-Rivera ◽  
Jiaxin Zhang ◽  
Rimpei Kawashita
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Labyrinth Seal ◽  
Secondary Flows ◽  
Tip Clearance ◽  
Inlet Pressure ◽  
Steam Turbines ◽  
Rotor Speed ◽  
Labyrinth Seals ◽  
Gas Seals

Abstract Gas labyrinth seals (LS) restrict secondary flows (leakage) in turbomachinery and their impact on the efficiency and rotordynamic stability of high-pressure compressors and steam turbines can hardly be overstated. Amongst seal types, the interlocking labyrinth seal (ILS), having teeth on both the rotor and on the stator, is able to reduce leakage up to 30% compared to other LSs with either all teeth on the rotor or all teeth on the stator. This paper introduces a revamped facility to test gas seals for their rotordynamic performance and presents measurements of the leakage and cavity pressures in a five teeth ILS. The seal with overall length/diameter L/D = 0.3 and small tip clearance Cr/D = 0.00133 is supplied with air at T = 298 K and increasing inlet pressure Pin = 0.3 MPa ∼ 1.3 MPa, while the exit pressure/inlet pressure ratio PR = Pout/Pin is set to range from 0.3 to 0.8. The rotor speed varies from null to 10 krpm (79 m/s max. surface speed). During the tests, instrumentation records the seal mass flow (ṁ) and static pressure in each cavity. In parallel, a bulk-flow model (BFM) and a computational fluid dynamics (CFD) analysis predict the flow field and deliver the same performance characteristics, namely leakage and cavity pressures. Both measurements and predictions agree closely (within 5%) and demonstrate the seal mass flow rate is independent of rotor speed. A modified flow factor Φ¯=m.T/PinD1-PR2 characterizes best the seal mass flow with a unique magnitude for all pressure conditions, Pin and PR.

scholarly journals An Experimental Study of Tip Clearance Flow in a Radial Inflow Turbine

1998 ◽  
Author(s):  
R. Dambach ◽  
H. P. Hodson ◽  
I. Huntsman
Keyword(s):  
Tip Clearance ◽  
Leakage Flow ◽  
Hot Wire ◽  
Tip Leakage Flow ◽  
Axial Turbine ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Radial Turbine ◽  
Clearance Flow ◽  
Radial Inflow Turbine

This paper describes an experimental investigation of tip clearance flow in a radial inflow turbine. Flow visualisation and static pressure measurements were performed. These were combined with hot-wire traverses into the tip gap. The experimental data indicates that the tip clearance flow in a radial turbine can be divided into three regions. The first region is located at the rotor inlet, where the influence of relative casing motion dominates the flow over the tip. The second region is located towards midchord, where the effect of relative casing motion is weakened. Finally a third region exists in the exducer, where the effect of relative casing motion becomes small and the leakage flow resembles the tip flow behaviour in an axial turbine. Integration of the velocity profiles showed that there is little tip leakage in the first part of the rotor because of the effect of scraping. It was found that the bulk of tip leakage flow in a radial turbine passes through the exducer. The mass flow rate, measured at four chordwise positions, was compared with a standard axial turbine tip leakage model. The result revealed the need for a model suited to radial turbines. The hot-wire measurements also indicated a higher tip gap loss in the exducer of the radial turbine. This explains why the stage efficiency of a radial inflow turbine is more affected by increasing the radial clearance than by increasing the axial clearance.

Numerical and Experimental Investigation on the Effect of Swirl Brakes on the Labyrinth Seals

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Dan Sun ◽  
Shuang Wang ◽  
Cheng-Wei Fei ◽  
Yan-Ting Ai ◽  
Ke-Ming Wang
Keyword(s):  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Impedance Method ◽  
Swirl Ratio ◽  
Labyrinth Seals ◽  
Rotating Speed ◽  
Simulation And Experiment ◽  
Computational Fluid Dynamics Cfd ◽  
Static Flow

Swirl brake influences the static and rotordynamic characteristics of labyrinth seal which are important in the prediction of turbomachine stability. To study the influence of the swirl brakes on improving seal stability, the effects of swirl brakes on the static and rotordynamic characteristics of labyrinth seals were investigated by the combination of numerical simulation and experiment. First, it was performed to the effects of swirl brake on the static flow characteristics of labyrinth seal with swirl ratio and pressure distribution based on computational fluid dynamics (CFD). And then a comparison between leakage predicted by the CFD model and measurement was presented to verify the accuracy of the simulation. Moreover, an experiment was implemented to analyze the rotordynamic characteristics of labyrinth seal using an improved impedance method based on an unbalanced synchronous excitation method on a rotor test rig. The influences of swirl brake density, length, inlet/outlet pressure ratio, and rotating speed were measured and discussed, respectively. The CFD numerical results show that the swirl brake effectively reduces the seal swirl ratio (∼60–75% less), circumferential pressure difference (∼25–85% less) so that the seal destabilizing forces decrease. With the increasing of the swirl vanes density and length, the seal leakage drops (∼8–20% less). The experimental rotordynamic characteristics results show that it is more obvious to reduce the cross-couple stiffness (∼50–300% less) and increase the direct damping (∼50–60% larger) with the increasing in the number and length of the swirl vanes, and thus the swirl brake improves the seal rotordynamic stability. The efforts of this paper provide a useful insight to clearly understand the effects of swirl brakes on the labyrinth seal static and rotordynamic characteristics, which is beneficial to improve the design of annular seals.

Performance evaluation of the inter-stage labyrinth seal for different tooth positions in an axial compressor

2017 ◽  
Vol 232 (6) ◽  
pp. 579-592 ◽  
Author(s):  
Xiaozhi Kong ◽  
Gaowen Liu ◽  
Yuxin Liu ◽  
Zhao Lei ◽  
Longxi Zheng
Keyword(s):  
Axial Compressor ◽  
Labyrinth Seal ◽  
Tip Clearance ◽  
Test Facility ◽  
Leakage Flow ◽  
Rotating Disc ◽  
Labyrinth Seals ◽  
Leakage Flows ◽  
Sealing Performance ◽  
Set Up

Labyrinth seals are normally used to control the leakage flow in the compressor stator well. The upstream and downstream rotor-stator cavities of the labyrinth seal can cause complex reverse leakage flows. Remarkable temperature increases and high swirl velocities are observed in this region. In addition, another characteristic of inter-stage labyrinth seal is that large expansions of rotor and stator may easily lead to severely rubbing between the teeth and shrouds, which can shorten the lifetime of the compressor obviously. Experiments were conducted at a rotating compressor inter-stage seal test facility. Different labyrinth rings were tested to compare the performances of inter-stage labyrinth seals with different tooth positions. Leakage flow rates, windage heating and swirl ratios in the outlet cavity were measured at different rotating speeds and pressure ratios. In order to get the working tip clearance accurately, the set up tip clearance was measured with plug gauges, while the radial displacements of rotating disc and stationary casing were measured separately with two high precision laser distance sensors. Numerical simulations were carried out to present the important flow physics responsible for the effects of different tooth positions. In this article, performances of different cases for single, double and triple teeth were investigated and the experimental data provide a new way for the design of inter-stage seals. This method can reduce the leakage flow and avoid severely rubbing at the same time by changing axial positions of teeth in the stator well. When teeth are placed downstream of the model and the tooth pitch is larger, the inter-stage seal would have better sealing performance. For triple teeth cases, N = 3-Case1 has the lowest discharge coefficients, 15% less than that of N = 3-Baseline.

Leakage and Windage Heating in Stepped Labyrinth Seals

2019 ◽  
Author(s):  
Kali Charan Nayak ◽  
Nomesh P. Kandaswamy ◽  
Syed Faheemulla
Keyword(s):  
Pressure Ratio ◽  
Labyrinth Seal ◽  
Vital Role ◽  
Step Height ◽  
Axial Position ◽  
Radial Clearance ◽  
Labyrinth Seals ◽  
Geometric Factors ◽  
Pitch Ratio ◽  
Computational Fluid Dynamics Cfd

Abstract Stepped labyrinth seals are used in multiple locations in the gas turbine with the intent to reduced leakage compared to straight labyrinth seals. However the selection of geometric factors in stepped labyrinth seals is critical to allow lower leakage in its operating envelope. Particularly the step height and axial position during the running condition play a vital role. The influence of these factors on the leakage, swirl development and windage heating in stepped labyrinth seal has not been thoroughly investigated in the previously published work. This paper focuses to study above effects with numerical simulations in a smooth four-fin stepped labyrinth seal. Specifically, a 2D axi-symmetric computational fluid dynamics (CFD) model is developed utilizing commercial finite volume-based software incorporating the standard k-ε turbulence model. Using this model, a broad parametric study is conducted by varying step height, axial position of the knife from the step, radial clearance and pressure ratio for a four-teeth stepped labyrinth seal. It has been observed that the seal leakage reduces with increase in step height to pitch ratio up to 0.35 and with further increase it tails off. The axial position of the tooth has strong influence on the flow structure and swirl development in the seal pocket.

Flexure Design for Progressive Clearance Labyrinth Seal

2012 ◽  
Author(s):  
Hrishikesh Deo ◽  
Xiaoqing Zheng
Keyword(s):  
Labyrinth Seal ◽  
Tip Clearance ◽  
The Self ◽  
Axial Stiffness ◽  
Simple Analytical Model ◽  
Labyrinth Seals ◽  
Lower Efficiency ◽  
Thermal Transients ◽  
Radial Stiffness ◽  
Lift Off

Turbo-machinery sealing is a challenging problem due to the varying clearances caused by thermal transients, vibrations or bearing lift–off. Conventional labyrinth seals have to be assembled with large clearances to avoid rubbing during rotor transients and this results in large leakage and lower efficiency. In our previous work, we have proposed a Progressive Clearance Labyrinth Seal which is mounted on flexures and employs progressively tighter teeth from the upstream to the downstream direction. The clearance progression gives rise to a feedback phenomenon whereby a small tip-clearance is maintained between the seal and the rotor. The flexures play a very important role in the design of this seal. They are required to have low radial stiffness relative to the fluidic feedback stiffness, so that the seal can move freely in response to the self-correcting forces. The axial stiffness has to be high to limit the displacement in that direction. Most importantly, the flexures need to provide extremely high twist stiffness, since a small twist can cause large changes in the clearance progression necessary for the self–correcting behavior. In this paper, we propose a novel zero–twist flexure architecture which preserves radial compliance and twist stiffness. We first create a simple analytical model to illustrate the design concept. An experimental setup is built and the design is validated on representative flexure geometry.

Rotordynamic Performance of a Negative-Swirl Brake for a Tooth-on-Stator Labyrinth Seal

2015 ◽  
Vol 138 (6) ◽  
Author(s):  
Dara W. Childs ◽  
James E. Mclean ◽  
Min Zhang ◽  
Stephen P. Arthur
Keyword(s):  
Labyrinth Seal ◽  
Test Results ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Stiffness Coefficients ◽  
Shaft Rotation ◽  
Computational Fluid Dynamics Cfd ◽  
The Cross ◽  
Inlet Conditions ◽  
The Stability

In the late 1970s, Benckert and Wachter (Technical University Stuttgart) tested labyrinth seals using air as the test media and measured direct and cross-coupled stiffness coefficients. They reported the following results: (1) fluid preswirl in the direction of shaft rotation creates destabilizing cross-coupled stiffness coefficients and (2) effective swirl brakes at the inlet to the seal can markedly reduce the cross-coupled stiffness coefficients, in many cases reducing them to zero. In recent years, “negative-swirl” swirl brakes have been employed, which attempt to reverse the circumferential direction of inlet flow, changing the sign of the cross-coupled stiffness coefficients and creating stabilizing stiffness forces. This study presents test results for a 16-tooth labyrinth seal with positive inlet preswirl (in the direction of shaft rotation) for the following inlet conditions: (1) no swirl brakes, (2) straight, conventional swirl brakes, and (3) negative-swirl swirl brakes. The negative-swirl swirl-brake designs were developed based on computational fluid dynamics (CFD) predictions. Tests were conducted at 10.2, 15.35, and 20.2 krpm with 70 bar of inlet pressure for pressure ratios of 0.3, 0.4, and 0.5. Test results include leakage and rotordynamic coefficients. In terms of leakage, the negative-swirl brake configuration leaked the least, followed by the conventional brake, followed by the no-brake design. Normalized to the negative-swirl brake configuration, the conventional-brake and no-brake configurations mass flow rate was greater, respectively, by factors of 1.04 and 1.09. The direct-stiffness coefficients are negative but small, consistent with past experience. The conventional swirl brake drops the destabilizing cross-coupled stiffness coefficients k by a factor of about 0.8 as compared to the no-brake results. The negative-swirl brake produces a change in sign of k with an appreciable magnitude; hence, the stability of forward precessing modes would be enhanced. In descending order, the direct-damping coefficients C are: no-swirl, negative-swirl, and conventional-swirl. Normalized in terms of the no-swirl case, C for the negative and conventional brake designs is, respectively, 0.7 and 0.6 smaller. The effective damping Ceff combines the effect of k and C. Ceff is large and positive for the negative-swirl configuration and near zero for the no-brake and conventional-brake designs. The present results for a negative-brake design are very encouraging for both eye-packing seals (where conventional swirl brakes have been previously employed) and division-wall and balance-piston seals, where negative shunt injection has been employed.

Sign in / Sign up

Export Citation Format

Share Document