Aerodynamic Performance of Turbine Center Frames With Purge Flows—Part II: The Influence of Individual Hub and Tip Purge Flows

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Stefan Zerobin ◽  
Christian Aldrian ◽  
Andreas Peters ◽  
Franz Heitmeir ◽  
Emil Göttlich
Keyword(s):  
High Pressure ◽  
Operating Conditions ◽  
High Pressure Turbine ◽  
Flow Rates ◽  
Purge Flow ◽  
Flow Evolution ◽  
Generation Mechanisms ◽  
The Impact ◽  
First Time ◽  
Time Assessment

The aerodynamic behavior of turbine center frame (TCF) ducts under the presence of high-pressure turbine (HPT) purge flows was experimentally investigated in this two-part paper. While the first part of the paper demonstrated the impact of varying the purge flow rates (PFR) on the loss behavior of two different TCF designs, the second part concentrates on the influence of individual hub and tip purge flows on the main flow evolution and loss generation mechanisms through the TCF ducts. Therefore, measurements were conducted at six different operating conditions in a one and a half stage turbine test setup, featuring four individual purge flows injected through the hub and tip, forward and aft cavities of the HPT rotor. The outcomes of this first-time assessment indicate that a HPT purge flow reduction generally benefits TCF performance. Decreasing one of the rotor case PFRs leads to an improved duct pressure loss. The purge flows from the rotor aft hub and tip cavities are demonstrated to play a particularly important role for improving the duct aerodynamic behavior. In contrast, the forward rotor hub purge flow actually stabilizes the flow in the TCF duct and reducing this purge flow can penalize TCF performance. These particular HPT/TCF interactions should be taken into account whenever high-pressure turbine purge flow reductions are pursued.

Impact of Individual High-Pressure Turbine Rotor Purge Flows on Turbine Center Frame Aerodynamics

2017 ◽  
Author(s):  
S. Zerobin ◽  
C. Aldrian ◽  
A. Peters ◽  
F. Heitmeir ◽  
E. Göttlich
Keyword(s):  
High Pressure ◽  
Pressure Loss ◽  
Turbine Rotor ◽  
Flow Conditions ◽  
High Pressure Turbine ◽  
Reference Case ◽  
University Of Technology ◽  
Purge Flow ◽  
Generation Mechanisms ◽  
The Impact

This paper presents an experimental study of the impact of individual high-pressure turbine purge flows on the main flow in a downstream turbine center frame duct. Measurements were carried out in a product-representative one and a half stage turbine test setup, installed in the Transonic Test Turbine Facility at Graz University of Technology. The rig allows testing at engine-relevant flow conditions, matching Mach, Reynolds, and Strouhal number at the inlet of the turbine center frame. The reference case features four purge flows differing in flow rate, pressure, and temperature, injected through the hub and tip, forward and aft cavities of the high-pressure turbine rotor. To investigate the impact of each individual cooling flow on the flow evolution in the turbine center frame, the different purge flows were switched off one-by-one while holding the other three purge flow conditions. In total, this approach led to six different test conditions when including the reference case and the case without any purge flow ejection. Detailed measurements were carried out at the turbine center frame duct inlet and outlet for all six conditions and the post-processed results show that switching off one of the rotor case purge flows leads to an improved duct performance. In contrast, the duct exit flow is dominated by high pressure loss regions if the forward rotor hub purge flow is turned off. Without the aft rotor hub purge flow, a reduction in duct pressure loss is determined. The purge flows from the rotor aft cavities are demonstrated to play a particularly important role for the turbine center frame aerodynamic performance. In summary, this paper provides a first-time assessment of the impact of four different purge flows on the flow field and loss generation mechanisms in a state-of-the-art turbine center frame configuration. The outcomes of this work indicate that a high-pressure turbine purge flow reduction generally benefits turbine center frame performance. However, the forward rotor hub purge flow actually stabilizes the flow in the turbine center frame duct and reducing this purge flow can penalize turbine center frame performance. These particular high-pressure turbine/turbine center frame interactions should be taken into account whenever high-pressure turbine purge flow reductions are pursued.

Aerodynamic Performance of Turbine Center Frames With Purge Flows—Part I: The Influence of Turbine Purge Flow Rates

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Stefan Zerobin ◽  
Andreas Peters ◽  
Sabine Bauinger ◽  
Ashwini Bhadravati Ramesh ◽  
Michael Steiner ◽  
...  
Keyword(s):  
Measurement Data ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Flow Structures ◽  
Flow Rates ◽  
Purge Flow ◽  
Mass Flows ◽  
The Individual ◽  
The Impact ◽  
First Time

This two-part paper deals with the influence of high-pressure turbine (HPT) purge flows on the aerodynamic performance of turbine center frames (TCF). Measurements were carried out in a product-representative one and a half-stage turbine test setup. Four individual purge mass flows differing in flow rate, pressure, and temperature were injected through the hub and tip, forward and aft cavities of the unshrouded HPT rotor. Two TCF designs, equipped with nonturning struts, were tested and compared. In this first part of the paper, the influence of different purge flow rates (PFR) is discussed, while in the second part of the paper, the impact of the individual hub and tip purge flows on the TCF aerodynamics is investigated. The acquired measurement data illustrate that the interaction of the ejected purge flow with the main flow enhances the secondary flow structures through the TCF duct. Depending on the PFR, the radial migration of purge air onto the strut surfaces directly impacts the loss behavior of the duct. The losses associated with the flow close to the struts and in the strut wakes are highly dependent on the relative position between the HPT vane and the strut leading edge (LE), as well as the interaction between vane wake and ejected purge flow. This first-time experimental assessment demonstrates that a reduction in the purge air requirement benefits the engine system performance by lowering the TCF total pressure loss.

scholarly journals Novel high-pressure turbine purge control features for increased stage efficiency

2017 ◽  
Vol 1 ◽  
pp. 68MK5V ◽  
Author(s):  
Rainer Schädler ◽  
Anestis I. Kalfas ◽  
Reza S. Abhari ◽  
Gregor Schmid ◽  
Tilmann auf dem Kampe ◽  
...  
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Gas Turbines ◽  
High Pressure Turbine ◽  
Axial Turbine ◽  
Seal Design ◽  
Geometrical Features ◽  
Purge Flow ◽  
The Impact ◽  
Stage Efficiency

AbstractRim seals throttle flow and have shown to impact the aerodynamic performance of gas turbines. The results of an experimental investigation of a rim seal exit geometry variation and its impact on the high-pressure turbine flow field are presented. A one-and-a-half stage, unshrouded and highly loaded axial turbine configuration with 3-dimensionally shaped blades and non-axisymmetric end wall contouring has been tested in an axial turbine facility. The exit of the rotor upstream rim seal was equipped with novel geometrical features which are termed as purge control features (PCFs) and a baseline rim seal geometry for comparison. The time-averaged and unsteady aerodynamic effects at rotor inlet and exit have been measured with pneumatic probes and the fast-response aerodynamic probe (FRAP) for three rim seal purge flow injection rates. Measurements at rotor inlet and exit reveal the impact of the geometrical features on the rim seal exit and main annulus flow field, highlighting regions of reduced aerodynamic losses induced by the modified rim seal design. Measurements at the rotor exit with the PCFs installed show a benefit in the total-to-total stage efficiency up to 0.4% for nominal and high rim seal purge flow rates. The work shows the potential to improve the aerodynamic efficiency by means of a well-designed rim seal exit geometry without losing the potential to block hot gas ingestion from the main annulus.

3D CFD Ingestion Evaluation of a High Pressure Turbine Rim Seal Disk Cavity

2008 ◽  
Author(s):  
A. V. Mirzamoghadam ◽  
G. Heitland ◽  
M. C. Morris ◽  
J. Smoke ◽  
M. Malak ◽  
...  
Keyword(s):  
High Pressure ◽  
Flow Rate ◽  
Steady Solution ◽  
Mixing Efficiency ◽  
Cfd Model ◽  
High Pressure Turbine ◽  
Stator Vane ◽  
Purge Flow ◽  
Model Setup ◽  
The Impact

The amount of cooling air assigned to seal high pressure turbine rim cavities is critical for performance as well as component life. Less air leads to excessive hot annulus gas ingestion and its penetration deep into the cavity compromising disk life. Excessive purge air adversely affects performance. The minimum purge (i.e. sealing) air requirement to control ingestion is also influenced by annulus circumferential pressure fluctuation present over the rim seal cavity. Its interaction with the platform gap resistance and the amount of purge air needs to be understood in order to reliably predict performance and component life. Work has commenced to investigate opportunities in reducing disk cavity purge flow requirements by studying ways to control ingestion. The study has been initiated with 3D CFD model setup/run mode options to benchmark main/cavity flow field interactions. The selection of the appropriate CFD model fidelity, however, is one of the main goals of this work. The CFD model phase has 3 options to be evaluated; 1) steady solution with mixing plane aft of the cavity, 2) steady solution with mixing plane forward of the cavity, 3) unsteady solution. Option 1 has been completed and is the subject of this paper. A reference HP turbine stage and disk cavity from an engine design was selected for the CFD study. The steady flow solution model captured the oscillatory movement and penetration depth of ingestion by varying purge flow rate and observing the impact on the mixing plane forward and aft of the disk cavity. Moreover, the influence of upstream stator vane airfoil fillet shape was also investigated. The entrained flow was established by starving the cavity and integrating the outflow along the disk. This value along with the nominal and intermediate cavity purge flows were validated against relevant sealing flow design correlations. At a radial location near the rim, an ingestion mixing efficiency value versus purge flow rate was obtained which correlates well with recent unsteady flow results from the literature.

Validation of MISES Two-Dimensional Boundary Layer Code for High-Pressure Turbine Aerodynamic Design

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Philip L. Andrew ◽  
Harika S. Kahveci
Keyword(s):  
Boundary Layer ◽  
High Pressure ◽  
Operating Cost ◽  
Design Tool ◽  
Operating Conditions ◽  
Aerodynamic Design ◽  
High Pressure Turbine ◽  
Reduce Operating Cost ◽  
Wide Range ◽  
Dimensional Boundary

Avoiding aerodynamic separation and excessive shock losses in gas turbine turbomachinery components can reduce fuel usage and thus reduce operating cost. In order to achieve this, blading designs should be made robust to a wide range of operating conditions. Consequently, a design tool is needed—one that can be executed quickly for each of many operating conditions and on each of several design sections, which will accurately capture loss, turning, and loading. This paper presents the validation of a boundary layer code, MISES, versus experimental data from a 2D linear cascade approximating the performance of a moderately loaded mid-pitch section from a modern aircraft high-pressure turbine. The validation versus measured loading, turning, and total pressure loss is presented for a range of exit Mach numbers from ≈0.5 to 1.2 and across a range of incidence from −10 deg to +14.5 deg relative to design incidence.

Time-Averaged and Time-Accurate Aerodynamic Effects of Forward Rotor Cavity Purge Flow for a High-Pressure Turbine: Part I—Analytical and Experimental Comparisons

2012 ◽  
Author(s):  
Brian R. Green ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Flow Path ◽  
Field Analysis ◽  
High Pressure Turbine ◽  
Purge Flow

The effect of rotor purge flow on the unsteady aerodynamics of a high-pressure turbine stage operating at design corrected conditions has been investigated both experimentally and computationally. The experimental configuration consisted of a single-stage high-pressure turbine with a modern film-cooling configuration on the vane airfoil as well as the inner and outer end-wall surfaces. Purge flow was introduced into the cavity located between the high-pressure vane and the high-pressure disk. The high-pressure blades and the downstream low-pressure turbine nozzle row were not cooled. All hardware featured an aerodynamic design typical of a commercial high-pressure ratio turbine, and the flow path geometry was representative of the actual engine hardware. In addition to instrumentation in the main flow path, the stationary and rotating seals of the purge flow cavity were instrumented with high frequency response, flush-mounted pressure transducers and miniature thermocouples to measure flow field parameters above and below the angel wing. Predictions of the time-dependent flow field in the turbine flow path were obtained using FINE/Turbo, a three-dimensional, Reynolds-Averaged Navier-Stokes CFD code that had the capability to perform both steady and unsteady analysis. The steady and unsteady flow fields throughout the turbine were predicted using a three blade-row computational model that incorporated the purge flow cavity between the high-pressure vane and disk. The predictions were performed in an effort to mimic the design process with no adjustment of boundary conditions to better match the experimental data. The time-accurate predictions were generated using the harmonic method. Part I of this paper concentrates on the comparison of the time-averaged and time-accurate predictions with measurements in and around the purge flow cavity. The degree of agreement between the measured and predicted parameters is described in detail, providing confidence in the predictions for flow field analysis that will be provided in Part II.

Prevention of Low-Frequency Vibration of High-Capacity Steam Turbine Units

1997 ◽  
Author(s):  
H. Kanki ◽  
Y. Kaneko ◽  
M. Kurosawa ◽  
T. Yamamoto ◽  
Y. Yamamoto ◽  
...  
Keyword(s):  
High Pressure ◽  
High Capacity ◽  
Low Frequency ◽  
Field Tests ◽  
Operating Conditions ◽  
Squeeze Film ◽  
High Pressure Turbine ◽  
Solution Approach ◽  
Vibration Excitation ◽  
Low Frequency Vibration

Abstract The causes of low-frequency vibration (subsynchronous vibration) of a high pressure turbine were investigated analytically and also via vibration excitation tests on actual machines under operation. From the results, it was concluded that low-frequency vibrations may be caused by either the decrease of the rotor system damping or by external forces, such as flow disturbance in the control stage and the rubbing between the rotor and casing. After identifying the cause of the low-frequency vibration, appropriate countermeasures such as installation of a squeeze-film damper and modification of valve opening sequence were taken. Vibration measurements and vibration excitation tests for the high pressure turbine under actual operating conditions were carried out in order to verify the validity of the countermeasures. These field tests confirmed that the problems of low-frequency vibration can be solved completely by taking the appropriate countermeasure depending on the cause of the vibration. This paper presents some field experiences of low-frequency vibration and the effective solution approach.

The Influence of Purge Flow Parameters on Heat Transfer and Film Cooling in Turbine Center Frames

2021 ◽  
Author(s):  
Patrick R. Jagerhofer ◽  
Marios Patinios ◽  
Tobias Glasenapp ◽  
Emil Göttlich ◽  
Federica Farisco
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Convective Heat Transfer Coefficient ◽  
Density Ratio ◽  
Constant Heat Flux ◽  
High Pressure Turbine ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Purge Flow

Abstract Due to stringent environmental legislation and increasing fuel costs, the efficiencies of modern turbofan engines have to be further improved. Commonly, this is facilitated by increasing the turbine inlet temperatures in excess of the melting point of the turbine components. This trend has reached a point where not only the high-pressure turbine has to be adequately cooled, but also components further downstream in the engine. Such a component is the turbine center frame (TCF), having a complex aerodynamic flow field that is also highly influenced by purge-mainstream interactions. The purge air, being injected through the wheelspace cavities of the upstream high-pressure turbine, bears a significant cooling potential for the TCF. Despite this, fundamental knowledge of the influencing parameters on heat transfer and film cooling in the TCF is still missing. This paper examines the influence of purge-to-mainstream blowing ratio, purge-to-mainstream density ratio and purge flow swirl angle on the convective heat transfer coefficient and the film cooling effectiveness in the TCF. The experiments are conducted in a sector-cascade test rig specifically designed for such heat transfer studies using infrared thermography and tailor-made flexible heating foils with constant heat flux. The inlet flow is characterized by radially traversing a five-hole-probe. Three purge-to-mainstream blowing ratios and an additional no purge case are investigated. The purge flow is injected without swirl and also with engine-similar swirl angles. The purge swirl and blowing ratio significantly impact the magnitude and the spread of film cooling in the TCF. Increasing blowing ratios lead to an intensification of heat transfer. By cooling the purge flow, a moderate variation in purge-to-mainstream density ratio is investigated, and the influence is found to be negligible.

THE INFLUENCE OF PURGE FLOW PARAMETERS ON HEAT TRANSFER AND FILM COOLING IN TURBINE CENTER FRAMES

2021 ◽  
pp. 1-26
Author(s):  
Patrick René Jagerhofer ◽  
Marios Patinios ◽  
Tobias Glasenapp ◽  
Emil Goettlich ◽  
Federica Farisco
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Density Ratio ◽  
Constant Heat Flux ◽  
Inlet Temperature ◽  
High Pressure Turbine ◽  
Turbofan Engines ◽  
Blowing Ratio ◽  
Purge Flow

Abstract The imperative improvement in the efficiency of turbofan engines is commonly facilitated by increasing the turbine inlet temperature. This development has reached a point where also components downstream of the high-pressure turbine have to be adequately cooled. Such a component is the turbine center frame (TCF), known for a complex aerodynamic flow highly influenced by purge-mainstream interactions. The purge air, being injected through the wheelspace cavities of the upstream high-pressure turbine, bears a significant cooling potential for the TCF. Despite this, fundamental knowledge of the influencing parameters on heat transfer and film cooling in the TCF is still missing. This paper examines the influence of purge-to-mainstream blowing ratio, density ratio and purge swirl angle on heat transfer and film cooling in the TCF. The experiments are conducted in a sector-cascade test rig specifically designed for such heat transfer studies using infrared thermography and tailor-made flexible heating foils with constant heat flux. Three purge-to-mainstream blowing ratios and an additional no purge case are investigated. The purge flow is injected without swirl and also with engine-similar swirl angles. The purge swirl and blowing ratio significantly impact the magnitude and the spread of film cooling in the TCF. Increasing blowing ratios lead to an intensification of heat transfer. By cooling the purge flow, a moderate variation in purge-to-mainstream density ratio is investigated, and the influence is found to be negligible.

Weibull Distributions Applied to Cost and Risk Analysis for Aero Engines

2008 ◽  
Author(s):  
D. S. Pascovici ◽  
K. G. Kyprianidis ◽  
F. Colmenares ◽  
S. O. T. Ogaji ◽  
P. Pilidis
Keyword(s):  
High Pressure ◽  
Risk Analysis ◽  
Economic Model ◽  
Spare Parts ◽  
Weibull Distributions ◽  
High Pressure Turbine ◽  
Aero Engines ◽  
The Cost ◽  
The Impact ◽  
Different Parts

This paper presents the use of Weibull formulation to the life analysis of different parts of the engine in order to estimate the cost of maintenance, the direct operating costs (DOC) and net present cost (NPC) of future type turbofan engines. The Weibull distribution is often used in the field of life data analysis due to its flexibility—it can mimic the behavior of other statistical distributions such as the normal and the exponential. The developed economic model is composed of three modules: a lifing module, an economic module and a risk module. The lifing module estimates the life of the high pressure turbine blades through the analysis of creep and fatigue over a full working cycle of the engine. The value of life calculated by the lifing is then taken as the baseline distribution to calculate the life of other important modules of the engine using the Weibull approach. Then the lower of the values of life of all the distributions is taken as time between overhaul (TBO), and used into the economic module calculations. The economic module uses the TBO together with the cost of labour and the cost of the engine (needed to determine the cost of spare parts) to estimate the cost of maintenance and DOC of the engine. In the present work five Weibull distributions are used for five important sources of interruption of the working life of the engine: Combustor, Life Limited Parts (LLP), High Pressure Compressor (HPC), General breakdowns and High Pressure Turbine (HPT). The risk analysis done in this work shows the impact of the breakdown of different parts of the engine on the NPC and DOC, the importance that each module of the engine has in its life, and how the application of the Weibull theory can help us in the risk assessment of future aero engines. A detailed explanation of the economic model is done in two other works (Pascovici et. al. [6] and Pascovici et. al. [7]), so in this paper only a general overview is done.

Sign in / Sign up

Export Citation Format

Share Document