Multiscale Material Modeling and Simulation of the Mechanical Behavior of Dual Phase Steels Under Different Strain Rates: Parametric Study and Optimization

2018 ◽  
Vol 140 (3) ◽  
Author(s):  
Tarek M. Belgasam ◽  
Hussein M. Zbib
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Volume Fraction ◽  
Rate Sensitivity ◽  
Tensile Tests ◽  
Dual Phase ◽  
Strain Rates ◽  
Microstructure Parameters ◽  
Dp Steels

Recent studies on developing dual phase (DP) steels showed that the combination of strength/ductility could be significantly improved when changing the volume fraction and grain size of phases in the microstructure depending on microstructure properties. Consequently, DP steel manufacturers are interested in predicting microstructure properties as well as optimizing microstructure design at different strain rate conditions. In this work, a microstructure-based approach using a multiscale material and structure model was developed. The approach examined the mechanical behavior of DP steels using virtual tensile tests with a full micro-macro multiscale material model to identify specific mechanical properties. Microstructures with varied ferrite grain sizes, martensite volume fractions, and carbon content in DP steels were also studied. The influence of these microscopic parameters at different strain rates on the mechanical properties of DP steels was examined numerically using a full micro-macro multiscale finite element method. An elasto-viscoplastic constitutive model and a response surface methodology (RSM) were used to determine the optimum microstructure parameters for a required combination of strength/ductility at different strain rates. The results from the numerical simulations were compared with experimental results found in the literature. The developed methodology proved to be a powerful tool for studying the effect and interaction of key strain rate sensitivity and microstructure parameters on mechanical behavior and thus can be used to identify optimum microstructural conditions at different strain rates.

The Effect of Strain Rate on the Mechanical Properties of Single Crystal NiAl

1990 ◽  
Vol 213 ◽  
Author(s):  
D.F. Lahrman ◽  
R.D. Field ◽  
R. Darolia
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Single Crystal ◽  
Rate Sensitivity ◽  
Tensile Tests ◽  
Deformation Mechanisms ◽  
Strain Rates ◽  
Test Results ◽  
Work Hardening Rate ◽  
Crystallographic Orientations

ABSTRACTIn this study, the strain rate sensitivity of single crystal NiAl has been investigated by performing tensile tests as a function of temperature and two strain rates. Three crystallographic orientations, [100], [110], and [111] were studied. The tensile test results investigated include yield strength, work hardening rate and plastic strain to failure. The data are discussed in terms of deformation mechanisms in NiAl.

scholarly journals Comparison of Nano-Mechanical Behavior between Selective Laser Melted SKD61 and H13 Tool Steels

2018 ◽  
Author(s):  
Jaecheol Yun ◽  
Van Luong Nguyen ◽  
Jungho Choe ◽  
Dong-yeol Yang ◽  
Hak-sung Lee ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Tool Steels ◽  
Pile Up ◽  
Scan Speed ◽  
Advanced Tool

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (hf) and the maximum depth (hmax) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s−1 and 0.1 s−1. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

Temperature and Stress State Influence on Mechanical Properties and Damage Evolution of Dual-Phase Steels

2014 ◽  
Vol 783-786 ◽  
pp. 886-891
Author(s):  
Mayerling Martinez ◽  
Jerôme Chottin ◽  
Eric Hug
Keyword(s):  
Mechanical Properties ◽  
Automotive Industry ◽  
Volume Fraction ◽  
Tensile Tests ◽  
Dual Phase ◽  
Dual Phase Steels ◽  
Transmission Electron ◽  
Structural Applications ◽  
Microstructure Parameters ◽  
Evolution Of Microstructure

Dual Phase steels are increasingly selected for structural applications including parts in automotive industry because of their interesting mechanical properties and their good formability. This work presents an experimental analysis of the evolution of microstructure of a DP1000 alloy submitted to thermomechanical loadings. Monotonous tensile tests were performed at various plastic strain levels up to fracture for temperatures ranging between 25 °C and 440 °C. A strong degradation of the mechanical properties is observed for temperatures higher than 275 °C. The evolution with plastic strains and temperature of the microstructure was studied by scanning and transmission electron microscopy. Different microstructure parameters such as volume fraction of martensite and carbide precipitation were taken into account in order to understand the mechanical behavior of DP1000 steels tested in this temperature range. The microstructural observations indicate that diminution of carbon in martensite, due to its diffusion to form carbides, could partially explain the drop in mechanical properties at around 275 °C.

scholarly journals New Approach In The Properties Evaluation Of Ultrafine-Grained OFHC Copper

2015 ◽  
Vol 60 (2) ◽  
pp. 605-614 ◽  
Author(s):  
T. Kvačkaj ◽  
A. Kováčová ◽  
J. Bidulská ◽  
R. Bidulský ◽  
R. Kočičko
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Tensile Tests ◽  
Coarse Grained ◽  
Wear Behaviour ◽  
Ofhc Copper ◽  
Strain Rates ◽  
Ultrafine Grained ◽  
Reduction Of Area ◽  
Pin On Disk

AbstractIn this study, static, dynamic and tribological properties of ultrafine-grained (UFG) oxygen-free high thermal conductivity (OFHC) copper were investigated in detail. In order to evaluate the mechanical behaviour at different strain rates, OFHC copper was tested using two devices resulting in static and dynamic regimes. Moreover, the copper was subjected to two different processing methods, which made possible to study the influence of structure. The study of strain rate and microstructure was focused on progress in the mechanical properties after tensile tests. It was found that the strain rate is an important parameter affecting mechanical properties of copper. The ultimate tensile strength increased with the strain rate increasing and this effect was more visible at high strain rates$({\dot \varepsilon} \sim 10^2 \;{\rm{s}}^{ - 1} )$. However, the reduction of area had a different progress depending on microstructural features of materials (coarse-grained vs. ultrafine-grained structure) and introduced strain rate conditions during plastic deformation (static vs. dynamic regime). The wear behaviour of copper was investigated through pin-on-disk tests. The wear tracks examination showed that the delamination and the mild oxidational wears are the main wear mechanisms.

Local Investigations of the Mechanical Properties of Ultrafine Grained Metals by Nanoindentations

2006 ◽  
Vol 503-504 ◽  
pp. 31-36 ◽  
Author(s):  
Johannes Mueller ◽  
Karsten Durst ◽  
Dorothea Amberger ◽  
Matthias Göken
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Fcc Metals ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Indentation Strain

The mechanical properties of ultrafine-grained metals processed by equal channel angular pressing is investigated by nanoindentations in comparison with measurements on nanocrystalline nickel with a grain size between 20 and 400 nm produced by pulsed electrodeposition. Besides hardness and Young’s modulus measurements, the nanoindentation method allows also controlled experiments on the strain rate sensitivity, which are discussed in detail in this paper. Nanoindentation measurements can be performed at indentation strain rates between 10-3 s-1 and 0.1 s-1. Nanocrystalline and ultrafine-grained fcc metals as Al and Ni show a significant strain rate sensitivity at room temperature in comparison with conventional grain sized materials. In ultrafine-grained bcc Fe the strain rate sensitivity does not change significantly after severe plastic deformation. Inelastic effects are found during repeated unloading-loading experiments in nanoindentations.

scholarly journals Strain-Rate-Dependent Deformation Behavior and Mechanical Properties of a Multi-Phase Medium-Manganese Steel

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 344 ◽  
Author(s):  
Simon Sevsek ◽  
Christian Haase ◽  
Wolfgang Bleck
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Deformation Behavior ◽  
Rate Sensitivity ◽  
Manganese Steel ◽  
Strain Rates ◽  
Rate Dependent ◽  
Medium Manganese Steel ◽  
Multi Phase

The strain-rate-dependent deformation behavior of an intercritically annealed X6MnAl12-3 medium-manganese steel was analyzed with respect to the mechanical properties, activation of deformation-induced martensitic phase transformation, and strain localization behavior. Intercritical annealing at 675 °C for 2 h led to an ultrafine-grained multi-phase microstructure with 45% of mostly equiaxed, recrystallized austenite and 55% ferrite or recovered, lamellar martensite. In-situ digital image correlation methods during tensile tests revealed strain localization behavior during the discontinuous elastic-plastic transition, which was due to the localization of strain in the softer austenite in the early stages of plastic deformation. The dependence of the macroscopic mechanical properties on the strain rate is due to the strain-rate sensitivity of the microscopic deformation behavior. On the one hand, the deformation-induced phase transformation of austenite to martensite showed a clear strain-rate dependency and was partially suppressed at very low and very high strain rates. On the other hand, the strain-rate-dependent relative strength of ferrite and martensite compared to austenite influenced the strain partitioning during plastic deformation, and subsequently, the work-hardening rate. As a result, the tested X6MnAl12-3 medium-manganese steel showed a negative strain-rate sensitivity at very low to medium strain rates and a positive strain-rate sensitivity at medium to high strain rates.

Stress-Strain Equations for Some Near-Eutectic Tin-Lead Solders

1991 ◽  
Vol 113 (4) ◽  
pp. 475-484 ◽  
Author(s):  
K. P. Jen ◽  
J. N. Majerus
Keyword(s):  
Strain Rate ◽  
Printed Circuit Boards ◽  
Volume Fraction ◽  
Total Error ◽  
Tensile Tests ◽  
Elastic Behavior ◽  
Plastic Behavior ◽  
Strain Rates ◽  
Stress Strain ◽  
Engineering Strain

This paper presents the evaluation of the stress-strain behavior, as a function of strain-rate, for three tin-lead solders at room temperature. This behavior is critically needed for reliability analysis of printed circuit boards (PCB) since handbooks list minimal mechanical properties for the eutectic solder used in PCBs. Furthermore, most handbook data are for stable eutectic microstructure whereas PCB solder has a metastable microstructure. All three materials were purchased as “eutectics.” However, chemical analysis, volume fraction determination, and microhardness tests show some major variations between the three materials. Two of the materials have a eutectic composition, and one does not. The true stress-strain equations of one eutectic and the one noneutectic material are determined from compressive tests at engineering strain-rates between 0.0002/s and 0.2/s. The second eutectic material is evaluated using tensile tests with strain-rates between 0.00017/s and 0.042/s. The materials appear to exhibit linear elastic behavior only at extremely small strains, i.e., less than 0.0005. However, this “elastic” behavior showed considerable variation, and depended upon the strain rate. In both tension and compression the eutectic alloy exhibits nonlinear plastic behavior, i.e., strain-softening followed by strain-hardening, which depends upon the strain rate. A quadratic equation σy = σy(ε˚/ε˚0) + A(ε˚/ε˚0)ε + B(ε˚/ε˚0)ε2 fit to the data gives correlation coefficients R2 > 0.91. The coefficients σy(ε˚/ε˚0), A(ε˚/ε˚0), B(ε˚/ε˚0) are fitted functions of the normalized engineering strain rate ε˚/ε˚0. Replicated experiments are used at each strain-rate so that a measure of the statistical variation could be estimated. Measures of error associated with the regression analysis are also obtained so that an estimate of the total error in the stress-strain relations can be made.

Dynamic Strain Aging in the Fe-Mn-Cu-C TWIP Steels

2013 ◽  
Vol 668 ◽  
pp. 861-864 ◽  
Author(s):  
Hai Jun Liu ◽  
Ding Yi Zhu ◽  
Xian Peng ◽  
Zhen Ming Hu ◽  
Ming Jie Wang
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Dynamic Strain Aging ◽  
Strain Aging ◽  
Rate Sensitivity ◽  
Tensile Tests ◽  
Dynamic Strain ◽  
Work Hardening Rate ◽  
Twip Steels ◽  
High Work

Strain rate jump tests were performed on the Fe-Mn-Cu-C TWIP Steels to determine the strain rate sensitivity, and serrated plastic flow was observed in the stress-strain curves during tensile tests at different constant strain rates ranging from 2.5×10-4S-1 to 2.5×10-2S-1. The Fe-Mn-Cu-C TWIP Steels exhibit high work hardening rate and outstanding mechanical properties, The excellent mechanical properties are attributed to dynamic strain aging(DSA) effect, which result from the interaction between Mn(Cu)-C atom atmosphere, C-vacancy, C-C pairs and moving dislocations.

Mechanical Anisotropy and Strain Rate Dependency Behavior of Ti6Al4V Produced Using E-Beam Additive Fabrication

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Leila Ladani ◽  
Jafar Razmi ◽  
Soud Farhan Choudhury
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Mechanical Anisotropy ◽  
Rate Dependency ◽  
Out Of Plane ◽  
Degree Of Anisotropy ◽  
Strain Rate Dependency

Anisotropic mechanical behavior is an inherent characteristic of parts produced using additive manufacturing (AM) techniques in which parts are built layer by layer. It is expected that in-plane and out-of-plane properties be different in these parts. E-beam fabrication is not an exception to this. It is, however, desirable to keep this degree of anisotropy to a minimum level and be able to produce parts with comparable mechanical strength in both in-plane and out-of-plane directions. In this manuscript, this degree of anisotropy is investigated for Ti6Al4V parts produced using this technique through tensile testing of parts built in different orientations. Mechanical characteristics such as Young's modulus, yield strength (YS), ultimate tensile strength (UTS), and ductility are evaluated. The strain rate effect on mechanical behavior, namely, strength and ductility, is also investigated by testing the material at a range of strain rates from 10−2 to 10−4 s−1. Local mechanical properties were extracted using nanoindentation technique and compared against global values (average values obtained by tensile tests). Although the properties obtained in this experiment were comparable with literature findings, test results showed that in-plane properties, elastic modulus, YS, and UTS are significantly higher than out-of-plane properties. This could be an indication of defects in between layers or imperfect bonding of the layers. Strong positive strain rate sensitivity was observed in out-of-plane direction. The strain rate sensitivity evaluation did not show strain rate dependency for in-plane directions. Local mechanical properties obtained through nanoindentation confirmed the findings of tensile test and also showed variation of properties caused by geometry.

Superplasticity of an AA2519 Aluminum Alloy

2016 ◽  
Vol 838-839 ◽  
pp. 278-284
Author(s):  
Ivan Zuiko ◽  
Marat Gazizov ◽  
Rustam Kaibyshev
Keyword(s):  
Strain Rate ◽  
Thermomechanical Processing ◽  
Rate Sensitivity ◽  
Initial Strain Rate ◽  
Tensile Tests ◽  
Sensitivity Coefficient ◽  
Initial Strain ◽  
Strain Rates ◽  
Average Grain Size ◽  
Elongation To Failure

A commercial AA2519 alloy with a chemical composition of Al-5.64Cu-0.33Mn-0.23Mg-0.15Zr (in wt. %) was subjected to two-step thermomechanical processing (TMP) providing the formation of fully recrystallized structure with an average grain size of ~7 mm in 3 mm thin sheets. Superplastic tensile tests were performed in the temperature interval 450-535°C and initial strain rates ranging from ~2.8 x 10-4 to ~6.0 x 10-1 s-1. The highest elongation-to-failure of ~750% appears at a temperature of ~525°C and an initial strain rate of ~1.4 × 10-4 s-1 with the corresponding strain rate sensitivity coefficient of ~0.46.

Sign in / Sign up

Export Citation Format

Share Document