Laminar Convective Nanofluid Flow Over a Backward-Facing Step With an Elastic Bottom Wall

2018 ◽  
Vol 10 (4) ◽  
Author(s):  
Fatih Selimefendigil ◽  
Hakan F. Öztop
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Elastic Modulus ◽  
Solid Particle ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Bottom Wall ◽  
Backward Facing Step ◽  
Particle Volume ◽  
Flexible Wall

In the present study, laminar forced convective nanofluid flow over a backward-facing step was numerically investigated. The bottom wall downstream of the step was flexible, and finite element method was used to solve the governing equations. The numerical simulation was performed for a range of Reynolds number (between 25 and 250), elastic modulus of the flexible wall (between 104 and 106), and solid particle volume fraction (between 0 and 0.035). It was observed that the flexibility of the bottom wall results in the variation of the fluid flow and heat transfer characteristics for the backward-facing step problem. As the value of Reynolds number and solid particle volume fraction enhances, local and average heat transfer rates increase. At the highest value of Reynolds number, heat transfer rate is higher for the case with the wall having lowest value of elastic modulus whereas the situation is reversed for other value of Reynolds number. Average Nusselt number reduces by about 9.21% and increases by about 6.1% for the flexible wall with the lowest elastic modulus as compared to a rigid bottom wall for Reynolds number of 25 and 250. Adding nano-additives to the base fluid results in higher heat transfer enhancements. Average heat transfer rates enhance by about 35.72% and 35.32% at the highest solid particle volume fraction as compared to nanofluid with solid volume fraction of 0.01 for the case with wall at the lowest and highest elastic modulus. A polynomial type correlation for the average Nusselt number along the flexible hot wall was proposed, which is dependent on the elastic modulus and solid particle volume fraction. The results of this study are useful for many thermal engineering problems where flow separation and reattachment coupled with heat transfer occur. Control of convective heat transfer for such configurations with wall flexibility and nanoparticle inclusion to the base fluid was aimed in this study to find the effects of various pertinent parameters for heat transfer enhancement.

Cooling of a Partially Elastic Isothermal Surface by Nanofluids Jet Impingement

2018 ◽  
Vol 140 (4) ◽  
Author(s):  
Fatih Selimefendigil ◽  
Hakan F. Öztop
Keyword(s):  
Reynolds Number ◽  
Nusselt Number ◽  
Elastic Modulus ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Jet Impingement ◽  
Particle Volume ◽  
Elastic Part ◽  
Hot Surface

Numerical study of nanofluid jet impingement cooling of a partially elastic isothermal hot surface was conducted with finite element method. The impingement surface was made partially elastic, and the effects of Reynolds number (between 25 and 200), solid particle volume fraction (between 0.01 and 0.04), elastic modulus of isothermal hot surface (between 104 and 106), size of the flexible part (between 7.5 w and 25 w), and nanoparticle type (spherical, cylindrical, blade) on the fluid flow and heat transfer characteristics were analyzed. It was observed that average Nusselt number enhances for higher Reynolds number, higher values of elastic modulus of flexible wall, smaller size of elastic part, and higher nanoparticle solid volume fraction and for cylindrical shaped particles. It is possible to change the maximum Nusselt number by 50.58% and 33% by changing the elastic modulus of the hot wall and size of elastic part whereas average Nusselt number changes by only 9.33% and 6.21%. The discrepancy between various particle shapes is higher for higher particle volume fraction.

Numerical Modelling of Nanofluid Heat Transfer Inside a Microchannel Heat Sink

2012 ◽  
Author(s):  
Benjamin Rimbault ◽  
Cong Tam Nguyen ◽  
Nicolas Galanis
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Sink ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Convective Heat Transfer Coefficient ◽  
Microchannel Heat Sink ◽  
Pumping Power ◽  
Particle Volume ◽  
Number Range

The problem of laminar flow and heat transfer of water-based nanofluids inside a 3D-microchannel heat sink was numerically investigated, considering temperature-dependent fluids properties. Results, obtained for the 250–2000 Reynolds number range, show that an important enhancement of surface convective heat transfer coefficient can be achieved by increasing the particle volume fraction. For given Reynolds number and particle fraction, a highest heat transfer enhancement is obtained using CuO-water nanofluid. However, the use of nanofluids considerably increases the wall friction and consequently the pumping power. The ‘heat transferred to fluid/pumping power’ ratio was calculated for nanofluids. For given Reynolds number and particle volume fraction, such a ratio was found lowest for CuO-water nanofluid, while alumina-water nanofluids provide similar results.

Heat transfer enhancement from inline and staggered arrays of cylinders in a heat exchanger using alumina-water nanofluid

2020 ◽  
pp. 1-31
Author(s):  
Mohd. Asif ◽  
Rashi Chaturvedi ◽  
Amit Dhiman
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Exchanger ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Nanoparticle Concentration ◽  
Transfer Enhancement ◽  
Particle Volume ◽  
Circular Tubes ◽  
Heat Transfer Augmentation

Abstract The flow of alumina-water nanofluid across heated circular tubes arranged in inline and staggered arrays in a heat exchanger has been studied. The thermophysical properties of the nanofluid are determined using Corcione correlations, which are based on several experiments. The nanoparticle diameter dp is between 10 and 50 nm, with particle volume fraction ϕ varying from 0.01 to 0.05 and Reynolds number Re ranging from 10 to 200. Heat transfer augmentation takes place when nanoparticle concentration is increased. Mean Nusselt number NuM is increased by 31% when ϕ is increased from 0.01 to 0.05 at Re = 200 and dp = 10 nm in an inline array and by 25% in a staggered array. The use of smaller nanoparticles significantly promotes the thermal performance of the heat exchange arrays; NuM is enhanced by 20% for the inline array and by 16% for the staggering array when dp decreases from 50 nm to 10 nm at Re = 200 and ϕ = 0.05. NuM of the staggering array of cylinders at Re = 200, dp = 10 nm and ϕ = 0.05 is 60% greater than NuM of an inline array of cylinders. Finally, correlations are derived for the calculation of NuM of inline as well as staggered arrays.

Investigation of the convective heat transfer and friction factor of magnetic Ni nanofluids within cylindrical pipes

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
M. Abdelkader ◽  
H. Ameur ◽  
Y. Menni
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Friction Factor ◽  
Turbulent Flows ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Constant Heat Flux ◽  
Particle Volume ◽  
Number Range

The current paper reports the results of numerical research on the magnetic Ni nanofluid flowing in a tube, developing turbulent flows under constant heat flux conditions. The numerical investigations are conducted for a Reynolds number range from 3,000 to 22,000, and a particle concentration range of 0% to 0.6%. The effects of the Reynolds number on the friction factor and Nusselt number are computed and compared satisfactorily with the experimental results of the literature. The classical correlations of Gnielinski, Notter – Rouse, and Pak and Cho are verified by predicting the Nusselt number of the Ni nanofluid. The obtained results revealed an enhancement in the heat transfer with the increase of magnetic Ni particle volume fraction and Reynolds number.

Experimental Investigation of Submerged Impinging Jet Using Cu-Water Nanofluid

2010 ◽  
Author(s):  
Qiang Li ◽  
Yimin Xuan ◽  
Feng Yu ◽  
Junjie Tan
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Volume Fraction ◽  
Cooling System ◽  
Heated Surface ◽  
Particle Volume Fraction ◽  
Jet Impingement ◽  
Particle Volume ◽  
Impingement Cooling ◽  
System Pressure

An experimental investigation was performed to study the heat transfer and flow features of Cu-water nanofluids (Cu particles with 26 nm diameter) in a submerged jet impingement cooling system. Three particular nozzle-to-heated surface distances (2, 4 and 6 mm) and four particle volume fractions (1.5%, 2.0%, 2.5% and 3.0%) are involved in the experiment. The experimental results reveal that the suspended nanoparticles increase the heat transfer performance of the base liquid in the jet impingement cooling system. Within the range of experimental parameters considered, it has been found that highest surface heat transfer coefficients can be achieved using a nozzle-to-surface distance of 4 mm and the nanofluid with 3.0% particle volume fraction. In addition, the experiments show that the system pressure drop of the dilute nanofluids is almost equal to that of water under the same entrance velocity.

scholarly journals Numerical analysis of heat transfer enhancement with the use of γ-Al2O3/water nanofluid and longitudinal ribs in a curved duct

2012 ◽  
Vol 16 (2) ◽  
pp. 469-480 ◽  
Author(s):  
Hosseinali Soltanipour ◽  
Parisa Choupani ◽  
Iraj Mirzaee
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Base Fluid ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Transfer Enhancement ◽  
Dean Number ◽  
Particle Volume ◽  
The Heat Transfer Coefficient

This paper presents a numerical investigation of heat transfer augmentation using internal longitudinal ribs and ?-Al2O3/ water nanofluid in a stationary curved square duct. The flow is assumed 3D, steady, laminar, and incompressible with constant properties. Computations have been done by solving Navier-Stokes and energy equations utilizing finite volume method. Water has been selected as the base fluid and thermo- physical properties of ?- Al2o3/ water nanofluid have been calculated using available correlations in the literature. The effects of Dean number, rib size and particle volume fraction on the heat transfer coefficient and pressure drop have been examined. Results show that nanoparticles can increase the heat transfer coefficient considerably. For any fixed Dean number, relative heat transfer rate (The ratio of the heat transfer coefficient in case the of ?- Al2o3/ water nanofluid to the base fluid) increases as the particle volume fraction increases; however, the addition of nanoparticle to the base fluid is more useful for low Dean numbers. In the case of water flow, results indicate that the ratio of heat transfer rate of ribbed duct to smooth duct is nearly independent of Dean number. Noticeable heat transfer enhancement, compared to water flow in smooth duct, can be achieved when ?-Al2O3/ water nanofluid is used as the working fluid in ribbed duct.

A Comparison on the Heat Transfer and Flow Characteristics of TiO2-Water Nanofluids Having Two Different Chemical Agents

2010 ◽  
Author(s):  
Weerapun Duangthongsuk ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Flow Characteristics ◽  
Average Diameter ◽  
Transfer Performance ◽  
Particle Volume ◽  
Tube Heat Exchanger ◽  
Two Samples

Heat transfer performance and flow characteristics of aqueous TiO2 nanofluids with particle volume fraction of 0.2% flowing under turbulent flow regime are investigated. The test section is a 1.5 m long counter-flow double tube heat exchanger. Two different nanofluids are used as working fluids at the same concentration. Firstly, TiO2 nanoparticles with mean diameters of 21 nm mixed with small amount of CTAB (about 0.01%) named “SAM 1”. Secondly, VP Disp. W740x provided by DEGUSSA AG Company is used and called “SAM 2”. The latter mixture is composed of TiO2 nanoparticle with average diameter of 21 nm dispersed in water. The pH values of nanofluid SAM 1 and SAM 2 are 7.6 and 7.5, respectively. The heat transfer performance and friction characteristics of two samples of nanofluid were presented. In addition, the Nusselt numbers predicted from the published correlation for nanofluids are compared with the present experimental data.

scholarly journals Improved Heat Transfer in Guar Gel Composites Reinforced with Randomly Distributed Glass Microspheres

2021 ◽  
Author(s):  
Ruifeng CAO ◽  
Taotao WANG ◽  
Yuxuan ZHANG ◽  
Hui WANG
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Particle Size ◽  
Composite Materials ◽  
Effective Thermal Conductivity ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Glass Microspheres ◽  
Particle Volume ◽  
Number Of Particles

Improved heat transfer in composites consisting of guar gel matrix and randomly distributed glass microspheres is extensively studied to predict the effective thermal conductivity of composites using the finite element method. In the study, the proper and probabilistic three-dimensional random distribution of microspheres in the continuous matrix is automatically generated by a simple and efficient random sequential adsorption algorithm which is developed by considering the correlation of three factors including particle size, number of particles, and particle volume fraction controlling the geometric configuration of random packing. Then the dependences of the effective thermal conductivity of composite materials on some important factors are investigated numerically, including the particle volume fraction, the particle spatial distribution, the number of particles, the nonuniformity of particle size, the particle dispersion morphology and the thermal conductivity contrast between particle and matrix. The related numerical results are compared with theoretical predictions and available experimental results to assess the validity of the numerical model. These results can provide good guidance for the design of advanced microsphere reinforced composite materials.

The Effect of Using Nanofluids on Triangular Microchannel Heat Exchanger Performance

2010 ◽  
Author(s):  
G. Bhaskaran ◽  
H. A. Mohammed ◽  
N. H. Shuaib
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Volume Fraction ◽  
Numerical Study ◽  
Particle Volume Fraction ◽  
Three Dimensional ◽  
Hydrodynamic Performance ◽  
Particle Volume ◽  
Microchannel Heat Exchanger

A numerical study is performed to study the effects of using various types of nanofluids on a triangular shaped microchannel heat exchanger (MCHE). The performance of an aluminum MCHE with various types of nanofluids such as Al2O3, CuO, SiO2, Ag and TiO2 and diamond particles with particle volume fraction of 2% using water as base fluid is comprehensively analyzed. The three-dimensional steady, laminar developing flow and conjugate heat transfer of a balanced MCHE were solved using finite volume method. In order to maintain laminar flow in the microchannels, Re number was ranged from 100 to 800. The other parameters tested in this study include the effects of Reynolds number towards the temperature, effectiveness and pressure drop of the MCHE. It is found that nanofluids have improved the temperature profile and heat transfer rate of the MCHE. The increase in pressure drop was minimal while the thermal and hydrodynamic performance of the heat exchanger was enhanced.

Sign in / Sign up

Export Citation Format

Share Document