Lubrication and Thermal Failure Mechanism Analysis in High-Speed Angular Contact Ball Bearing

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Wang Yunlong ◽  
Wang Wenzhong ◽  
Li Yulong ◽  
Zhao Ziqiang
Keyword(s):  
Rotational Speed ◽  
High Speed ◽  
Ball Bearing ◽  
Rolling Bearing ◽  
Operating Conditions ◽  
Contact Forces ◽  
Mechanism Analysis ◽  
Angular Contact Ball Bearing ◽  
Thermal Failure ◽  
Lubrication Performance

Lubrication analysis of rolling bearing is often conducted with assumed operating conditions, which does not consider the effect of internal dynamics of rolling bearing. In this paper, the effects of the applied load and bearing rotational speed on the lubrication performance in an angular contact ball bearing are conducted, which combines the bearing dynamic analysis and thermo-elastohydrodynamic lubrication (TEHL) analysis. First, the internal motions and contact forces are obtained from the developed bearing dynamic model, and then were integrated into the TEHL model to investigate the lubrication performance of the bearing. The results show that the rotational speed and external load has significant effects on film thickness, temperature, and power loss; if the improper axial load is applied for certain bearing speed, the lubrication performance will deteriorate and thermal failure may occur; there exists critical load or speed to keep good lubrication performance and avoid thermal failure; the skidding contributes to the thermal failure and bad lubrication performance.

Kinematic investigation and fatigue life analysis of angular contact ball bearing in wide speed range based on raceway friction

2020 ◽  
Vol 72 (7) ◽  
pp. 845-850
Author(s):  
Yue Liu
Keyword(s):  
Fatigue Life ◽  
Peer Review ◽  
High Speed ◽  
Ball Bearing ◽  
Operating Conditions ◽  
Angular Contact Ball Bearing ◽  
Content Type ◽  
Speed Range ◽  
Uniform Model ◽  
Wide Speed Range

Purpose The purpose of this paper is to clarify the relationship between fatigue life and kinematics of angular contact ball bearing. It proposes a new modeling method of spin to roll ratio based on raceway friction, which is more accurate than the traditional raceway control theory. Design/methodology/approach The uniform model of spin to roll ratio based on raceway friction in a wide speed range is proposed using quasi-statics method, which considers centrifugal force, gyroscopic moment, friction force of raceway and other influencing factors. The accuracy is considerably improved compared with the static model without increasing too much computation. Findings A uniform model for spin to roll ratio of angular contact ball bearing based on raceway friction is established, and quite different relationships between fatigue life and speed under two operating conditions are found. Research limitations/implications The conclusion of this paper is based on the bearing basic fatigue life calculation theory provided by ISO/TS 16281; however, the accuracy of theory needs to be further verified. Practical implications This paper provides guidance for applying angular contact ball bearing, especially at a high speed. Originality/value This paper reveals the changing trend of fatigue life of angular contact ball bearing with the speed under different loads. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2020-0030

Analysis of Thermal Effect on Elastohydrodynamic Lubrication in Angular Contact Ball Bearing

2015 ◽  
Vol 741 ◽  
pp. 443-448
Author(s):  
Bao Ming Wang ◽  
Xia Lun Yun ◽  
Xing Yao Liao ◽  
Xue Song Mei
Keyword(s):  
Temperature Rise ◽  
High Speed ◽  
Ball Bearing ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Oil Viscosity ◽  
Angular Contact Ball Bearing ◽  
Scanning Method ◽  
Lubrication Performance ◽  
Thermal Ehl

Based on the theory of point contact thermal elastohydrodynamic lubrication (EHL),the mathematical models for the thermal EHL of high-speed angular contact ball bearing are established. Multi-grid method and multigrid integration method are respectively used to calculate out the film pressure and film thickness respectively,and the column-by-column scanning method is used to calculate temperature rise of isothermal EHL and thermal EHL. The calculation results show that, under the pure rolling condition, temperature rise of oil film temperature is mainly caused by the compression work and shear heat at inlet and the heat in contact zone mainly comes from the inlet and the heat conduction around; the temperature rise results in oil viscosity lower and the lubricating film thinner ,in this way it reduces the lubrication performance in contact pair.

The Non-Uniform Preloading Effect on Stiffness Behaviour of Angular Contact Ball Bearings

2012 ◽  
Author(s):  
Wenwu Wu ◽  
Jun Hong ◽  
Xiaohu Li ◽  
Yang Li ◽  
Baotong Li
Keyword(s):  
High Speed ◽  
Ball Bearing ◽  
Operating Conditions ◽  
Structural Performance ◽  
Angular Contact Ball Bearing ◽  
Actual Operating ◽  
Bearing Life ◽  
Bearing Stiffness ◽  
Increasing Demand ◽  
Bearing System

With the increasing demand of higher operating speed for bearing system, more challenges have been exposed on the maintaining of the bearing performance. Preloading is an effective method to handle these challenges. Traditionally, the preloading of bearing system has been applied by uniform approaches such as rigid preload and constant preload. However, this treatment may hardly deal with the optimization of preloading problem due to the non-uniformity of the bearing stiffness becomes more apparent under high-speed operating conditions. A novel and practical approach is therefore presented in this paper to incorporate the non-uniformity effect to improve the structural performance of bearing under actual operating conditions. Firstly, the critical relationship between the stiffness behaviour and the non-uniform preload is evaluated for bearing system. The stiffness problem of angular contact ball bearing system is then formulated analytically by Jones’ model. With this approach, boundary conditions are achieved to solve the local contact deformation and predict the bearing life under non-uniform preload. Finally, both the uniform preload and the non-uniform preload cases for bearing system are simulated under various operating conditions. Comparing with traditional methods, the proposed method can provide a better solution in both stiffness and life that will enable a designer to obtain a deep insight on the optimization of bearing system.

Ball Bearing Response to Cage Unbalance

1986 ◽  
Vol 108 (3) ◽  
pp. 462-466 ◽  
Author(s):  
P. K. Gupta ◽  
J. F. Dill ◽  
J. W. Artuso ◽  
N. H. Forster
Keyword(s):  
Entire Range ◽  
High Speed ◽  
Ball Bearing ◽  
Operating Conditions ◽  
Angular Contact Ball Bearing ◽  
Turbine Engine ◽  
Wide Range ◽  
Inner Race ◽  
Good Agreement ◽  
Engine Bearing

Motion of the cage in a high-speed angular contact ball bearing is experimentally investigated as a function of prescribed unbalance, up to operating speeds corresponding to three million DN. The predictions of cage motion made by the recently developed computer model, ADORE, are validated in the light of the experimental data. It is shown the cage whirl velocity is essentially equal to its angular velocity at all levels of unbalance and over a wide range of operating conditions. For the inner race guided turbine engine bearing, the cage/race interaction takes place directly opposite to the location of the unbalance and the severity of the interaction increases with the level of unbalance and the operating speed. ADORE predictions, over the entire range of unbalance and bearing operating conditions, are in very good agreement with the experimental observations.

Computational-experimental research of the stiffness of high-speed spindles

2020 ◽  
pp. 33-39
Author(s):  
I.A. Zverev
Keyword(s):  
Elastic Deformation ◽  
Experimental Research ◽  
Rotational Speed ◽  
High Speed ◽  
Ball Bearing ◽  
Deformation Model ◽  
Ball Bearings ◽  
Radial Load ◽  
Angular Contact Ball Bearing ◽  
Spindle Unit

The stiffness indices of high-speed spindle units on angular contact ball bearings at high rotational speeds are investigated. It is found, that the spindle rotational speed, radial load, bearing temperature, type and magnitude of the preload in the bearings significantly affect the stiffness of the spindle unit. Keywords: high-speed spindle unit, angular contact ball bearing, elastic-deformation model. [email protected]

Experimental investigation of cage motions in an angular contact ball bearing

2017 ◽  
Vol 231 (8) ◽  
pp. 1041-1055 ◽  
Author(s):  
Baogang Wen ◽  
Hongjun Ren ◽  
Hao Zhang ◽  
Qingkai Han
Keyword(s):  
Experimental Investigation ◽  
High Speed ◽  
Ball Bearing ◽  
Dimensional Space ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Axial Loads ◽  
Angular Contact Ball Bearing ◽  
Radial Forces ◽  
External Loads

The commonly known effects of both the rotating speeds and external loads on the bearing dynamics or life behaviors are mostly caused by its cage dynamics, because of the complicated contact and collision interactions between the cage and other parts such as the inner or outer rings and balls. In this paper, experimental investigation of dynamic motions of a cage is carried out under various rotating speeds and external loads in a ball bearing. On a bearing test rig, the cage motions in axial and radial directions are measured by use of eddy transducers installed inside the bearing house and the subpanel. Then the measured results are analyzed by fast Fourier transform and compared at different operating conditions including rotating speeds, axial and radial forces, or moments. The three-dimensional space motions of the cage are also constructed to illustrate its different modes. Results reveal that the cage motions are typically periodic in the three directions. The motion frequencies consist of the cage rotating frequency and its multi-frequency, the inner ring rotating frequency, and also some combination frequencies of the cage and inner ring. The obtained characteristic frequencies of the cage motion in axial are similar to that in radial, but different in the variety of amplitudes under the same operating conditions. The increment of rotating speeds and axial loads of the bearing gradually make the whirl trajectories of the cage mass center regular, and enlarge its whirl radii. Instead, the whirl trajectories change from well-defined patterns to complicated ones, and its whirl radii decrease on increasing the radial loads and moments of the bearing. All the obtained experimental results are useful references for dynamic design and life prediction of high-speed and low-load bearings commonly used in many machines.

A New Proposal for Explicit Angle Calculation in Angular Contact Ball Bearing

2005 ◽  
Vol 128 (2) ◽  
pp. 468-478 ◽  
Author(s):  
J -F. Antoine ◽  
G. Abba ◽  
A. Molinari
Keyword(s):  
Contact Angle ◽  
Rotational Speed ◽  
High Speed ◽  
Analytical Approach ◽  
Ball Bearing ◽  
Good Precision ◽  
Angular Contact Ball Bearing ◽  
The Relationship ◽  
Special Case ◽  
Angle Calculation

In order to optimize the mechanical behavior of high speed rotors, it is useful to know the load-displacement law of the angular-contact ball bearing. The relationship between preload, speed, and contact angle is studied and a new analytical approach is proposed, giving explicitly and with good precision the contact angle versus preload and rotational speed for the special case of elastically preloaded high speed angular-contact ball bearing.

Experimental and Analytical Investigation of High Speed Turbocharger Ball Bearings

2011 ◽  
Vol 133 (12) ◽  
Author(s):  
Ankur Ashtekar ◽  
Farshid Sadeghi
Keyword(s):  
High Speed ◽  
Ball Bearing ◽  
Analytical Investigation ◽  
Rotor System ◽  
Operating Conditions ◽  
Experimental Results ◽  
Test Rig ◽  
Angular Contact Ball Bearing ◽  
Turbine Wheel ◽  
Bearing Dynamics

The objectives of this investigation were to design and construct a high speed turbocharger test rig (TTR) to measure dynamics of angular contact ball bearing rotor system, and to develop a coupled dynamic model for the ball bearing rotor system to corroborate the experimental and analytical results. In order to achieve the objectives of the experimental aspect of this study, a test rig was designed and developed to operate at speeds up to 70,000 rpm. The rotating components (i.e., turbine wheels) of the TTR were made to be dynamically similar to the actual turbocharger. Proximity sensors were used to record the turbine wheel displacements while accelerometers were used to monitor the rotor vibrations. The TTR was used to examine the dynamic response of the turbocharger under normal and extreme operating conditions. To achieve the objectives of analytical investigation, a discrete element ball bearing model was coupled through a set of interface points with a component mode synthesis rotor model to simulate the dynamics of the turbocharger test rig. Displacements of the rotor from the analytical model were corroborated with experimental results. The analytical and experimental results are in good agreement. The bearing rotor system model was used to examine the bearing component dynamics. Effects of preloading and imbalance were also found to have significant effects on turbocharger rotor and bearing dynamics.

Investigation of the High Speed Rolling Bearing Temperature Rise With Oil-Air Lubrication

2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Shuyun Jiang ◽  
Hebing Mao
Keyword(s):  
Temperature Rise ◽  
High Speed ◽  
Ball Bearing ◽  
Rotation Speed ◽  
Rolling Bearing ◽  
Operating Conditions ◽  
Steel Ball ◽  
Pipe Length ◽  
Air Lubrication ◽  
Hybrid Ceramic

The oil-air lubrication system has been widely used for rolling ball bearing. However, as the rotation speed increases, the temperature rise will increase dramatically, resulting in shortening the service life of the ball bearing. The existing literature has offered valuable fundamental data about the oil-air lubrication of rolling bearing; however, there are still some problems that concerned the oil-air lubrication, which are not addressed. In this study, an experiment setup to investigate the oil-air lubrication for the high speed ball bearing has been developed, and performance tests of hybrid ceramic and steel ball bearings under the extensive operating conditions including oil-air supply pipe length, bearing preload, lube interval, oil type, oil viscosity, nozzle design, and rotation speed have been conducted. The test results show that the bearing has the lowest temperature rise with the pipe length of 1.5 m. For the steel ball bearing, the proper preload decreases with increasing of the rotating speed, and the temperature rise of the hybrid ceramic ball bearing is not sensitive to the axial preload. There exists a proper amount of lubricant for the bearing at each rotational speed; and a larger amount of lubricant is required for the bearing as the rotating speed increases. The tested bearings under different speeds have almost the same lowest temperature rise under the lubricant with the viscosity of 100 cSt; a higher or lower viscosity will increase the bearing temperature rises. The nozzle design is an important factor to affect the temperature rise of the ball bearing, and the suitable geometric parameter of the nozzle is closely related to the cage landing method of the bearing. The temperature rise of tested bearings increases with the increase in the rotation speed; and the hybrid ceramic ball bearing always has a lower temperature rise than that of the steel ball bearing at the same operating conditions.

Recent Patents on the Angular Contact Ball Bearing of High-Speed Motorized Spindle

2020 ◽  
Vol 13 ◽  
Author(s):  
Yudong Bao ◽  
Linkai Wu ◽  
Yanling Zhao ◽  
Chengyi Pan
Keyword(s):  
High Speed ◽  
Ball Bearing ◽  
Rapid Development ◽  
Ceramic Materials ◽  
Development Trend ◽  
Numerical Control ◽  
Angular Contact Ball Bearing ◽  
Practical Applications ◽  
High Speed Cutting ◽  
Advantages And Disadvantages

Background:: Angular contact ball bearings are the most popular bearing type used in the high speed spindle for machining centers, The performance of the bearing directly affects the machining efficiency of the machine tool, Obtaining a higher value is the direction of its research and development. Objective:: By analyzing the research achievements and patents of electric spindle angular contact bearings, summarizing the development trend provides a reference for the development of electric spindle bearings. Methods:: Through the analysis of the relevant technology of the electric spindle angular contact ball bearing, the advantages and disadvantages of the angular contact ball bearing are introduced, and the research results are combined with the patent analysis. Results:: With the rapid development of high-speed cutting and numerical control technology and the needs of practical applications, the spindle requires higher and higher speeds for bearings. In order to meet the requirements of use, it is necessary to improve the bearing performance by optimizing the structure size and improving the lubrication conditions. Meanwhile, reasonable processing and assembly methods will also have a beneficial effect on bearing performance. Conclusion:: With the continuous deepening of bearing technology research and the use of new structures and ceramic materials has made the bearing's limit speed repeatedly reach new highs. The future development trend of high-speed bearings for electric spindles is environmental protection, intelligence, high speed, high precision and long life.

Sign in / Sign up

Export Citation Format

Share Document