scholarly journals Experiments on the Effects of Reynolds Number and Advance Ratio on the Unfolding of Disorganization in Low-Speed Underwater Propulsors With Vibrating Blades

2017 ◽  
Vol 140 (4) ◽  
Author(s):  
Promode R. Bandyopadhyay
Keyword(s):  
Acoustic Radiation ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Limit Cycle Oscillation ◽  
Blade Vibration ◽  
Low Reynolds Numbers ◽  
Low Speed ◽  
Aircraft Wings ◽  
Wall Boundary Layer ◽  
Cycle Oscillation

Ships and submarines are acoustic hazards to marine life. The rational control of acoustic radiation would be possible at least at low Reynolds numbers if the underlying organization buried in seeming randomness is revealed. We build a novel low-speed propulsor where all blades undergo small-amplitude pitch oscillation while spinning at large pitch angles at transitional chord Reynolds numbers (3.75 × 103 ≤ Rec ≤ 3.75 × 104) and advance ratios (0.51 ≤ J ≤ 4.89). We measure and model time-averaged and temporal thrust. The relationship between the time-averaged and the temporal thrust is observed when the latter is mapped as limit cycle oscillation (LCO), or departure from it. High-thrust coefficients occurring at large (30 deg and 45 deg) angles of amplitude of blade vibration are modeled assuming poststall lift enhancement due to flapping blades when a leading edge vortex (LEV) forms, while the lower thrust coefficients occurring at 20 deg are modeled by its absence. The disorganization in temporal thrust increases with J and Rec. An external orthogonal oscillator, perhaps a vibration, is modeled to couple with the thrust oscillator for temporal control of disorganization. The unfolding disorganization is seen as a departure from LCO, and it is attenuated by smooth-wall boundary-layer fencing, compared to unfenced smooth and rough surfaces. When the fencing properties of the leading edge tubercles of whale fins are recognized, the ratio of the spacing of the fences and chord is found to be similar (0.5–1.0) in both whale flippers and aircraft wings.

Investigation on the effect of leading edge tubercles of sweptback wing at low reynolds number

2020 ◽  
Vol 21 (6) ◽  
pp. 621
Author(s):  
Veerapathiran Thangaraj Gopinathan ◽  
John Bruce Ralphin Rose ◽  
Mohanram Surya
Keyword(s):  
Leading Edge ◽  
Reynolds Numbers ◽  
Sweep Angle ◽  
Laminar Separation ◽  
Low Reynolds Numbers ◽  
Flow Energy ◽  
Airplane Wing ◽  
Low Reynolds ◽  
Naca 0015 ◽  
Wing Performance

Aerodynamic efficiency of an airplane wing can be improved either by increasing its lift generation tendency or by reducing the drag. Recently, Bio-inspired designs have been received greater attention for the geometric modifications of airplane wings. One of the bio-inspired designs contains sinusoidal Humpback Whale (HW) tubercles, i.e., protuberances exist at the wing leading edge (LE). The tubercles have excellent flow control characteristics at low Reynolds numbers. The present work describes about the effect of tubercles on swept back wing performance at various Angle of Attack (AoA). NACA 0015 and NACA 4415 airfoils are used for swept back wing design with sweep angle about 30°. The modified wings (HUMP 0015 A, HUMP 0015 B, HUMP 4415 A, HUMP 4415 B) are designed with two amplitude to wavelength ratios (η) of 0.1 & 0.24 for the performance analysis. It is a novel effort to analyze the tubercle vortices along the span that induce additional flow energy especially, behind the tubercles peak and trough region. Subsequently, Co-efficient of Lift (CL), Co-efficient of Drag (CD) and boundary layer pressure gradients also predicted for modified and baseline (smooth LE) models in the pre & post-stall regimes. It was observed that the tubercles increase the performance of swept back wings by the enhanced CL/CD ratio in the pre-stall AoA region. Interestingly, the flow separation region behind the centerline of tubercles and formation of Laminar Separation Bubbles (LSB) were asymmetric because of the sweep.

scholarly journals Force and flowfield measurements to understand unsteady aerodynamics of cycloidal rotors in hover at ultra-low Reynolds numbers

2019 ◽  
Vol 11 ◽  
pp. 175682931983367
Author(s):  
Carolyn M Reed ◽  
David A Coleman ◽  
Moble Benedict
Keyword(s):  
Separation Bubble ◽  
Fluid Dynamic ◽  
Unsteady Aerodynamics ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Dynamic Stall ◽  
Static Case ◽  
Low Reynolds Numbers ◽  
Curvature Effects ◽  
Low Reynolds

This paper provides a fundamental understanding of the unsteady fluid-dynamic phenomena on a cycloidal rotor blade operating at ultra-low Reynolds numbers (Re ∼ 18,000) by utilizing a combination of instantaneous blade force and flowfield measurements. The dynamic blade force coefficients were almost double the static ones, indicating the role of dynamic stall. For the dynamic case, the blade lift monotonically increased up to ±45° pitch amplitude; however, for the static case, the flow separated from the leading edge after around 15° with a large laminar separation bubble. There was significant asymmetry in the lift and drag coefficients between the upper and lower halves of the trajectory due to the flow curvature effects (virtual camber). The particle image velocimetry measured flowfield showed the dynamic stall process during the upper half to be significantly different from the lower half because of the reversal of dynamic virtual camber. Even at such low Reynolds numbers, the pressure forces, as opposed to viscous forces, were found to be dominant on the cyclorotor blade. The power required for rotation (rather than pitching power) dominated the total blade power.

Separation and Transition Control on an Aft-Loaded Ultra-High-Lift LP Turbine Blade at Low Reynolds Numbers: High-Speed Validation

2006 ◽  
Vol 129 (2) ◽  
pp. 340-347 ◽  
Author(s):  
Maria Vera ◽  
Xue Feng Zhang ◽  
Howard Hodson ◽  
Neil Harvey
Keyword(s):  
Surface Roughness ◽  
Mach Number ◽  
Surface Finish ◽  
High Speed ◽  
Reynolds Numbers ◽  
High Lift ◽  
Low Reynolds Numbers ◽  
Low Speed ◽  
Transition Mechanism ◽  
Low Reynolds

This paper presents the second part of an investigation of the combined effects of unsteadiness and surface roughness on an aft-loaded ultra-high-lift low-pressure turbine (LPT) profile at low Reynolds numbers. The investigation has been performed using low- and high-speed cascade facilities. The low- and high-speed profiles have been designed to have the same normalized isentropic Mach number distribution. The low-speed results have been presented in the first part (Zhang, Vera, Hodson, and Harvey, 2006, ASME J. Turbomach., 128, pp. 517–527). The current paper examines the effect of different surface finishes on an aft-loaded ultra-high-lift LPT profile at Mach and Reynolds numbers representative of LPT engine conditions. The surface roughness values are presented along with the profile losses under steady and unsteady inflow conditions. The results show that the use of a rough surface finish can be used to reduce the profile loss. In addition, the results show that the same quantitative values of losses are obtained at high- and low-speed flow conditions. The latter proves the validity of the low-speed approach for ultra-high-lift profiles for the case of an exit Mach number of the order of 0.64. Hot-wire measurements were carried out to explain the effect of the surface finish on the wake-induced transition mechanism.

Experimental Study of Flow Separation over NACA633018 Wing with Synthetic Jet Control at Low Reynolds Numbers

2012 ◽  
Vol 29 (1) ◽  
pp. 45-52 ◽  
Author(s):  
C.-Y. Lin ◽  
F.-B. Hsiao
Keyword(s):  
Reynolds Number ◽  
Flow Separation ◽  
Separation Bubble ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Laminar Separation ◽  
Low Reynolds Numbers ◽  
Jet Control

AbstractThis paper experimentally studies flow separation and aerodynamic performance of a NACA633018 wing using a series of piezoelectric-driven disks, which are located at 12% chord length from the leading edge to generate a spanwise-distributed synthetic jets to excite the passing flow. The experiment is conducted in an open-type wind tunnel with Reynolds numbers (Re) of 8 × 104 and 1.2 × 105, respectively, based on the wing chord. The oscillations of the synthetic jet actuators (SJAs) disturb the neighboring passage flow on the upper surface of the wing before the laminar separation takes place. The disturbances of energy influence the downstream development of boundary layers to eliminate or reduce the separation bubble on the upper surface of the wing. Significant lift increase and drag decrease are found at the tested Reynolds number of 8 × 104 due to the actuators excitation. Furthermore, the effect of drag also reduces dominant with increasing Reynolds number, but the increase on lift is reduced with the Reynolds number increased.

scholarly journals Aerodynamic and performance characteristics of a passive leading edge Kruger flap at low Reynolds numbers

2012 ◽  
Vol 116 (1181) ◽  
pp. 757-767 ◽  
Author(s):  
V. M. Moraris ◽  
N. J. Lawson ◽  
K. P. Garry
Keyword(s):  
Numerical Study ◽  
Leading Edge ◽  
Detailed Comparison ◽  
Reynolds Numbers ◽  
Aerodynamic Performance ◽  
Low Reynolds Numbers ◽  
Initial Stage ◽  
And Performance ◽  
High Angles Of Attack ◽  
Basic Configuration

Abstract An experimental and numerical study was performed on a Clark Y aerofoil with a 10% chord leading edge Kruger flap to examine its aerodynamic performance at Reynolds numbers of 0·6 × 106, 1 × 106, and 1·6 × 106, to help to identify the forces and moments acting on a basic configuration. A detailed comparison of the numerical and experimental data is presented in this paper. The leading edge flap was effective at high angles of attack with an increase in CL of up to 18% over a conventional no flap configuration and delayed separation by up to 3°. The moments around the Kruger flap rotation point were calculated from the numerical analysis as an initial stage in the design of a UAV passive flap system and they are also presented in the paper.

Sign in / Sign up

Export Citation Format

Share Document