scholarly journals Improved J Estimation by GE/EPRI Method for the Thin-Walled Pipes With Small Constant-Depth Circumferential Surface Cracks

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
X. Liu ◽  
Z. X. Lu ◽  
Y. Chen ◽  
Y. L. Sui ◽  
L. H. Dai
Keyword(s):  
Influence Functions ◽  
J Integral ◽  
Surface Cracks ◽  
Constant Depth ◽  
Long Distance ◽  
Small Constant ◽  
Wide Range ◽  
Thin Walled ◽  
Plastic Influence Functions ◽  
J Estimation

Application of thin-walled high strength steel has become a trend in the oil and gas transportation system over long distance. Failure assessment is an important issue in the construction and maintenance of the pipelines. This work provides an engineering estimation procedure to determine the J-integral for the thin-walled pipes with small constant-depth circumferential surface cracks subject to the tensile loading based upon the General Electric/Electric Power Research (GE/EPRI) method. The values of elastic influence functions for stress intensity factor and plastic influence functions for fully plastic J-integral are derived in tabulated forms through a series of three-dimensional (3D) finite element (FE) calculations for a wide range of crack geometries and material properties. Furthermore, the fit equations for elastic and plastic influence functions are developed, where the effects of crack geometries are explicitly revealed. The new influence functions lead to an efficient J estimation and can be well applied for structural integrity assessment of thin-walled pipes with small constant-depth circumferential surface cracks under tension.

scholarly journals Failure Assessment for the High-Strength Pipelines with Constant-Depth Circumferential Surface Cracks

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
X. Liu ◽  
Z. X. Lu ◽  
Y. Chen ◽  
Y. L. Sui ◽  
L. H. Dai
Keyword(s):  
Finite Element ◽  
Practical Interest ◽  
High Strength ◽  
Influence Functions ◽  
Surface Cracks ◽  
Constant Depth ◽  
Long Distance ◽  
Integrity Assessment ◽  
Failure Assessment ◽  
Bending Loads

In the oil and gas transportation system over long distance, application of high-strength pipeline steels can efficiently reduce construction and operation cost by increasing operational pressure and reducing the pipe wall thickness. Failure assessment is an important issue in the design, construction, and maintenance of the pipelines. The small circumferential surface cracks with constant depth in the welded pipelines are of practical interest. This work provides an engineering estimation procedure based upon the GE/EPRI method to determine the J-integral for the thin-walled pipelines with small constant-depth circumferential surface cracks subject to tension and bending loads. The values of elastic influence functions for stress intensity factor and plastic influence functions for fully plastic J-integral estimation are derived in tabulated forms through a series of three-dimensional finite element calculations for different crack geometries and material properties. To check confidence of the J-estimation solution in practical application, J-integral values obtained from detailed finite element (FE) analyses are compared with those estimated from the new influence functions. Excellent agreement of FE results with the proposed J-estimation solutions for both tension and bending loads indicates that the new solutions can be applied for accurate structural integrity assessment of high-strength pipelines with constant-depth circumferential surface cracks.

scholarly journals On the Calculation of Stress Intensity Factors and J-Integrals Using the Submodeling Technique

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Eduard Marenić ◽  
Ivica Skozrit ◽  
Zdenko Tonković
Keyword(s):  
Stress Intensity ◽  
Limit Load ◽  
Analytical Approximation ◽  
J Integral ◽  
Surface Cracks ◽  
Linear Elastic ◽  
Reference Stress ◽  
Wide Range ◽  
Reference Pressure ◽  
Axial Surface

In the present paper, calculations of the stress intensity factor (SIF) in the linear-elastic range and the J-integral in the elastoplastic domain of cracked structural components are performed by using the shell-to-solid submodeling technique to improve both the computational efficiency and accuracy. In order to validate the submodeling technique, several numerical examples are analyzed. The influence of the choice of the submodel size on the SIF and the J-integral results is investigated. Detailed finite element solutions for elastic and fully plastic J-integral values are obtained for an axially cracked thick-walled pipe under internal pressure. These values are then combined, using the General Electric/Electric Power Research Institute method and the reference stress method, to obtain approximate values of the J-integral at all load levels up to the limit load. The newly developed analytical approximation of the reference pressure for thick-walled pipes with external axial surface cracks is applicable to a wide range of crack dimensions.

Fully-Plastic J and CTOD Solutions for Pipes With Circumferential Surface Cracks Subjected to Combined Bending and Tension

2011 ◽  
Author(s):  
Lui´s F. S. Parise ◽  
Claudio Ruggieri
Keyword(s):  
Material Properties ◽  
Tensile Load ◽  
Estimation Procedure ◽  
Large Set ◽  
J Integral ◽  
Surface Cracks ◽  
Defect Assessment ◽  
Wide Range ◽  
Bending Load ◽  
Assessment Procedures

This work provides an estimation procedure to determine the J-integral and CTOD for pipes with circumferential surface cracks subjected to combined bending and tensile load for a wide range of crack geometries and material (hardening) based upon fully-plastic solutions. A summary of the methodology upon which J and CTOD are derived sets the necessary framework to determine nondimensional functions h1 and h2 applicable to a wide range of crack geometries and material properties characteristic of structural, pressure vessel and pipeline steels. The extensive nonlinear, 3-D numerical analyses provide a large set of solutions for J and CTOD which enters directly into fitness-for-service (FFS) analyses and defect assessment procedures of cracked pipes and cylinders subjected to bending load.

J and CTOD Estimation Procedure for Circumferentially Cracked Pipes Based on Fully-Plastic Solutions

2010 ◽  
Author(s):  
Mario S. G. Chiodo ◽  
Claudio Ruggieri
Keyword(s):  
Pressure Vessel ◽  
Material Properties ◽  
Estimation Procedure ◽  
Large Set ◽  
J Integral ◽  
Surface Cracks ◽  
Defect Assessment ◽  
Wide Range ◽  
Bending Load ◽  
Assessment Procedures

This work provides an estimation procedure to determine the J-integral and CTOD for pipes with circumferential surface cracks subjected to bending load for a wide range of crack geometries and material (hardening) based upon fully-plastic solutions. A summary of the methodology upon which J and CTOD are derived sets the necessary framework to determine nondimensional functions h1 and h2 applicable to a wide range of crack geometries and material properties characteristic of structural, pressure vessel and pipeline steels. The extensive nonlinear, 3-D numerical analyses provide a large set of solutions for J and CTOD which enters directly into fitness-for-service (FFS) analyses and defect assessment procedures of cracked pipes and cylinders subjected to bending load.

Stress intensity factors for semi-elliptical surface cracks in semicircularly notched tension plates

1997 ◽  
Vol 32 (3) ◽  
pp. 229-236 ◽  
Author(s):  
X B Lin ◽  
R A Smith
Keyword(s):  
Stress Intensity ◽  
Stress Intensity Factors ◽  
Crack Depth ◽  
Finite Thickness ◽  
J Integral ◽  
Surface Cracks ◽  
Intensity Factors ◽  
Wide Range ◽  
Half Length ◽  
Half Thickness

Stress intensity factors for semi-elliptical surface cracks located at the centre of a semicircular edge notch in a finite thickness plate subjected to a remote tensile load are presented in a tabulated format. A wide range of geometry ratios are considered. They are all combinations of the following ratios: the ratio of crack surface half-length to plate half-thickness, c/t = 0.2, 0.4, 0.6, 0.8 and 0.95; the ratio of crack depth to surface half-length, a/c = 0.2, 0.4, 0.6, 0.8 and 1; and the ratio of notch radius to plate half-thickness, r/t = 0.5, 1, 2 and 3. Both the quarter-point displacement and J.-integral methods based on three-dimensional finite element analyses were employed for the calculation of stress intensity factors. The calculation accuracy was studied by analysing the J.-integral path independence and comparing stress intensity factor results with other solutions available in the literature.

Fully-Plastic Strain-Based J Estimation Scheme for Circumferential Surface Cracks in Pipes Subjected to Reeling

2013 ◽  
Author(s):  
Luís F. S. Parise ◽  
Claudio Ruggieri ◽  
Noel P. O’Dowd
Keyword(s):  
Driving Force ◽  
Driving Forces ◽  
Fracture Behaviour ◽  
Applied Strain ◽  
J Integral ◽  
Surface Cracks ◽  
Crack Driving Force ◽  
Numerical Assessment ◽  
Estimation Scheme ◽  
J Estimation

Modern installation techniques for marine pipelines and subsea risers are often based on the reel-lay method, which introduces significant (plastic) strains on the pipe during reeling and un-reeling. The safe assessment of crack-like flaws under such conditions requires accurate estimations of the elastic-plastic crack driving forces, ideally expressed in a strain-based formulation to better account for the displacement controlled nature of the reeling method. This paper aims to facilitate such assessments by presenting a strain-based expression of the well-known EPRI estimation scheme for the J integral, which is directly based upon fully plastic descriptions of fracture behaviour under significant plasticity. Parametric finite element simulations of bending of circumferentially cracked pipes have been conducted for a set of crack geometries, pipe dimensions and material hardening properties representative of current applications. These provide the numerical assessment of the crack driving force upon which the non-dimensional factors of the EPRI methodology, which scale J with applied strain, are derived. Finally, these factors are presented in convenient graphical and tabular forms, thus allowing the direct and accurate assessment of the J integral for circumferentially cracked pipes subjected to reeling.

Plastic influence functions for calculating J-integral of complex-cracks in pipe

2016 ◽  
Vol 146 ◽  
pp. 11-21 ◽  
Author(s):  
Jae-Uk Jeong ◽  
Jae-Boong Choi ◽  
Moon-Ki Kim ◽  
Nam-Su Huh ◽  
Yun-Jae Kim
Keyword(s):  
Influence Functions ◽  
J Integral ◽  
Plastic Influence Functions

Elastic-Plastic Fracture Mechanics Method for Poor Penetration Crack in Welded Piping Branch Junction

2008 ◽  
Author(s):  
Yong-Qiang Bai ◽  
Tong Wang ◽  
Lianghai Lv ◽  
Liang Sun ◽  
Jian Shuai
Keyword(s):  
Fracture Mechanics ◽  
Crack Front ◽  
Crack Depth ◽  
Influence Functions ◽  
Stress Strain ◽  
Elastic Plastic ◽  
Inner Radius ◽  
Plastic Influence Functions ◽  
Remote Stress ◽  
J Estimation

This paper provides two types of engineering J estimation equations for welded piping branch junctions with poor penetration crack under internal pressure. The first type is the so-called GE/EPRI type J estimation equation based on Ramberg-Osgood (R-O) materials. Based on detailed 3-D FE results using deformation plasticity, plastic influence functions for fully plastic J components are tabulated for practical ranges of the inner radius of brace to the inner radius of chord ratio, the thickness of brace to the thickness of chord, the thickness of chord to the inner radius of chord ratio, the crack depth to the thickness of chord ratio, the strain hardening index for the R-O material, and the location along the poor penetration crack front. Based on tabulated plastic influence functions, the GE/EPRI-type J estimation equation along the crack front is proposed. For more general application, the effective remote stress method based on GE/EPRI-type solutions is provided. This method provides a simpler equation for J, which could be used for any stress-strain relationship material, including Ramborg-Osgood (R-O) material and non-R-O materials under monotonic increasing loading. The proposed effective remote stress based J estimation equation is compared with elastic-plastic 3-D FE results using actual stress–strain data for a Type 304 strainless steel. Good agreement between the FE results and the proposed reference stress based J estimation provides confidence in the use of the proposed method for elastic-plastic fracture mechanics of pressurized welded piping branch junction.

Sign in / Sign up

Export Citation Format

Share Document