scholarly journals Residual Stress From Cold Expansion of Fastener Holes: Measurement, Eigenstrain, and Process Finite Element Modeling

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Renan L. Ribeiro ◽  
Michael R. Hill
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Slow Crack Growth ◽  
Measurement Data ◽  
Equivalent Plastic Strain ◽  
Contour Method ◽  
Elastic Behavior ◽  
Plastic Behavior ◽  
Cold Expansion

Cold expansion (CX) is a material processing technique that has been widely used in the aircraft industry to enhance fatigue life of structural components containing holes. CX introduces compressive hoop residual stresses that slow crack growth near the hole edge. The objective of this paper is to predict residual stresses arising from cold expansion using two different finite element (FE) approaches, and compare the results to measurement data obtained by the contour method. The paper considers single-hole, double-hole, and triple-hole configurations with three different edge margins. The first FE approach considers process modeling, and includes elastic–plastic behavior, while the second approach is based on the eigenstrain method, and includes only elastic behavior. The results obtained from the FE models are in good agreement with one another, and with measurement data, especially close to the holes, and with respect to the effect of edge margin on the residual stress distributions. The distribution of the residual stress and equivalent plastic strain around the holes is also explored, and the results are discussed in detail. The eigenstrain method was found to be very useful, providing generally accurate predictions of residual stress.

Residual Stress Measurements in Single and Multi-Pass Groove Weld Specimens Using Neutron Diffraction and the Contour Method

2006 ◽  
Vol 524-525 ◽  
pp. 671-676 ◽  
Author(s):  
M. Kartal ◽  
Mark Turski ◽  
Greg Johnson ◽  
Michael E. Fitzpatrick ◽  
S. Gungor ◽  
...  
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Neutron Diffraction ◽  
Residual Stresses ◽  
Cross Section ◽  
Welding Process ◽  
Contour Method ◽  
Residual Stress Field ◽  
Process Measurements ◽  
Good Agreement

This paper describes the measurement of longitudinal residual stresses within specially designed 200x180x25mm groove weld specimens. The purpose of these measurements was to compare the residual stress field arising from single and multi-pass weld beads laid down within the constraint of a groove in order to validate finite element simulations of the welding process. Measurements were made over the cross section at the mid-bead length, utilising the relatively new Contour method and neutron diffraction. Results from these measurements indicate a larger peak tensile longitudinal residual stresses within the weld region of the multi-pass weld sample. Good agreement is found between both techniques.

Effect of Residual Forming Stresses on Fracture in ERW Pipe

2016 ◽  
Author(s):  
Ted L. Anderson ◽  
Gregory W. Brown
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Fracture Behavior ◽  
Finite Element Simulations ◽  
Finite Element Analyses ◽  
Forming Process ◽  
Cold Expansion ◽  
The Past

Many older pipelines contain significant residual stress due to the forming process. Cold expansion or a normalizing heat treatment can virtually eliminate residual forming stresses, but these practices were less common in the past. In the absence of cold expansion or normalization, residual forming stresses can be reduced by hydrostatic testing or operating pressures, but not eliminated entirely. Residual stresses can contribute to fracture in pipelines, particularly when the material toughness is low. This article presents a series of analyses that seek to quantify the magnitude of residual forming stresses as well as their impact on pipeline integrity. The pipe forming process was simulated with elastic-plastic finite element analyses, which considered the effect of subsequent loading on relaxation of residual stresses. A second set of finite element simulations were used to quantify the effect of residual stresses on fracture behavior.

scholarly journals On the Accuracy of Finite Element Models Predicting Residual Stresses in Quenched Stainless Steel

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1308 ◽  
Author(s):  
Israel Medina-Juárez ◽  
Jeferson Araujo de Oliveira ◽  
Richard J. Moat ◽  
Francisco Alfredo García-Pastor
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Residual Stresses ◽  
Contour Method ◽  
Stress Profile ◽  
304L Stainless Steel ◽  
Fem Model ◽  
Residual Stress Profile ◽  
Industry Applications

Prediction of residual stress profiles after quenching is important for a range of industry applications. Finite element method (FEM) models have the capability of simulate the cooling and stress evolution during quenching; however, they are very dependent on the heat transfer coefficient (HTC) imposed on the surface. In this paper, an analysis of the HTC effect on the accuracy of the residual stress profile after quenching a 304L stainless steel Jominy sample was conducted. The FEM model was validated in its thermal accuracy using thermocouples and the residual stress profile was measured using the contour method. The results show that a thermally validated FEM model may yield results which overestimate the tensile residual stress and underestimates the compressive residual stress maxima while accurately calculating the maxima positions from the quenched edge. The FEM model accuracy was not improved by modifying the HTC or by using a different thermal expansion coefficient. The results are discussed in terms of the effect of plasticity due to twinning in the residual stresses calculated by the FEM model.

scholarly journals Determination of Directional Residual Stresses by the Contour Method

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1104 ◽  
Author(s):  
Josef Hodek ◽  
Antonín Prantl ◽  
Jan Džugan ◽  
Pavel Strunz
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Electrical Discharge Machine ◽  
Measurement Data ◽  
Coordinate Measuring Machine ◽  
Material Model ◽  
Element Model ◽  
Contour Method ◽  
Diffraction Measurement ◽  
Measuring Machine

This study evaluated residual stresses in heat-treated specimens made of 316L stainless steel using FE analysis and compared them with stresses determined by the contour method. Contour method is usually used just for evaluation of residual stresses that are normal to the cut plan. In the current study this approach is extended and both normal and tangential stresses are determined. The specimens were cut using wire electrical discharge machine and the contours of the cut were measured using a coordinate measuring machine. The prior treatment of the specimens was simulated using the finite-element method. An appropriate boundary condition and temperature-dependent material model were employed. The finite-element model was validated against neutron-diffraction measurement data. The results showed a good agreement in normal and tangential directions of stress.

Manufacture, Residual Stress Measurement and Analysis of a VVER-440 Nozzle Mockup

2013 ◽  
Author(s):  
Levente Tatár ◽  
Gyula Török ◽  
David J. Smith ◽  
Son Do ◽  
Carsten Ohms ◽  
...  
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Welding Process ◽  
Full Scale ◽  
Residual Stress Measurement ◽  
Contour Method ◽  
Scale Model ◽  
Fe Model

As part of the STYLE EU FP7 project a modified 1:5 scale replica of a VVER-440 type reactor pressure vessel inlet nozzle was manufactured. The nozzle included a dissimilar metal weld of the type found in full-scale nozzles. This scale model was developed to permit accurate measurements to be made and detailed finite element (FE) models to be developed without recourse to using a full scale mock-up. It was also found that a full-scale mock-up would not permit the application of certain residual stress measurement methods. Temperatures and displacements were recorded during welding of the dissimilar metals, with measurements used to guide simulation of the welding process using finite element models. Through thickness residual stress profiles were measured using a comprehensive range of different techniques, such as deep hole drilling, neutron diffraction, magnetic Barkhausen noise. Usage of contour method had been planned too, but it but could not be accomplished in due time. The measured residual stresses obtained by the different methods are presented and compared. Measured residual stresses, temperatures and displacements were then used to validate the results derived from the FE model.

Measurements of Residual Stresses Using Mechanical Strain Relaxation Methods and Mapping in a Thin-Walled Girth Welded Pipe Mock-Up

2016 ◽  
Author(s):  
Karim Serasli ◽  
Remi Romac ◽  
Douglas Cave
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Mechanical Strain ◽  
Contour Method ◽  
Hole Drilling ◽  
Mapping Technique ◽  
Thin Walled ◽  
Welded Pipe ◽  
Welding Processes

Girth welded pipes such as those located offshore on platforms in the North Sea are subjected to highly corrosive environment. The need to consider welding residual stresses in the assessment of the fitness for service and damages to these pipes when investigating local corrosion damages across a welded region is therefore important for the operators of the platforms and the manufacturers of the pipes. This paper presents a review of work carried out to ascertain the welding residual stresses present within a thin-walled girth welded pipe mock-up made from steel API 5LX Grade 52. The mock-up was manufactured to replicate typical pipes used to convey gas, oil and water through the platforms. The mock-up was of diameter 762mm and of thickness 19mm. The incremental deep hole drilling (iDHD) technique and the contour method were applied to characterize the residual stresses in the weld and heat affected zone of the specimen. The results of these measurements are presented and compared to highlight agreements and discrepancies in the measured residual stress distributions using these different techniques. Most residual stress measurement methods are limited in terms of their stress and spatial resolution, the number of measurable stress tensor components and their quantifiable measurement uncertainty. In contrast, finite element simulations of welding processes provide full field distributions of residual stresses, with results dependent on the quality of the input conditions available. As measurements and predictions are not often the same, the true residual stress state is therefore difficult to determine. In this paper, through-thickness residual stress measurements are made using the contour and iDHD methods and these residual stresses measured using the iDHD technique are then used as input to a residual stress mapping technique provided within a finite element analysis to reconstruct the residual stress field in the whole specimen. The technique is applied iteratively to converge to a balanced solution which is not necessarily unique. The solution can then be reused for further simulations and residual stress analyses, such as corrosion simulation. Results of the reconstruction are presented here.

Evaluation on Residual Stresses in Thick Titanium Welded Alloys

2018 ◽  
Vol 941 ◽  
pp. 1095-1098
Author(s):  
Hai Yan Zhao ◽  
Pu Xie
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Experimental Measurement ◽  
Contour Method ◽  
Weld Shape ◽  
Heating Stage

In this work, both Finite element simulated method and contour method experimental measurement are used to obtain residual stresses of different Titanium welded alloys, the results show that the maximum of the residual stress is mainly related to the internal restraint degree which formed inside of the thickness, the distribution of the residual stress depends primarily on the shape of weld shape. The heating stage plays a major role in relaxing the residual stress in this research. 95% of the residual stress is relieved in the temperature rising period, and about 75% of it is relieved in the temperature rising period when the temperature is above 500°C.

scholarly journals Residual Stress Measurements in Mo/CuCrZr Tiles Using Neutron Diffraction

2008 ◽  
Vol 59 ◽  
pp. 299-303
Author(s):  
K. Mergia ◽  
Marco Grattarola ◽  
S. Messoloras ◽  
Carlo Gualco ◽  
Michael Hofmann
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Neutron Diffraction ◽  
Residual Stresses ◽  
Heat Sink ◽  
High Yield ◽  
Fusion Reactors ◽  
Plasma Facing Components ◽  
Induced Stresses ◽  
Compliant Layer

In plasma facing components (PFC) for nuclear fusion reactors tungsten or carbon based tiles need to be cooled through a heat sink. The joint between the PFC and the heat sink can be realized using a brazing process through the employment of compliant layer of either a low yield material, like copper, or a high yield material, like molybdenum. Experimental verification of the induced stresses during the brazing process is of vital importance. Strains and residual stresses have been measured in Mo/CuCrZr brazed tiles using neutron diffraction. The strains and stresses were measured in Mo tile along the weld direction and at different distances from it. The experimental results are compared with Finite Element Simulations.

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

2000 ◽  
Vol 123 (1) ◽  
pp. 150-154
Author(s):  
John H. Underwood ◽  
Michael J. Glennon
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Fatigue Life ◽  
Yield Strength ◽  
Residual Stresses ◽  
Solid Mechanics ◽  
Element Model ◽  
Pressure Vessels ◽  
Material Strength ◽  
Element Analysis

Laboratory fatigue life results are summarized from several test series of high-strength steel cannon breech closure assemblies pressurized by rapid application of hydraulic oil. The tests were performed to determine safe fatigue lives of high-pressure components at the breech end of the cannon and breech assembly. Careful reanalysis of the fatigue life tests provides data for stress and fatigue life models for breech components, over the following ranges of key parameters: 380–745 MPa cyclic internal pressure; 100–160 mm bore diameter cannon pressure vessels; 1040–1170 MPa yield strength A723 steel; no residual stress, shot peen residual stress, overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid mechanics analysis. Shot peen and overload residual stresses are modeled by superposing typical or calculated residual stress distributions on the applied stresses. Overload residual stresses are obtained directly from the finite element model of the breech, with the breech overload applied to the model in the same way as with actual components. Modeling of the fatigue life of the components is based on the fatigue intensity factor concept of Underwood and Parker, a fracture mechanics description of life that accounts for residual stresses, material yield strength and initial defect size. The fatigue life model describes six test conditions in a stress versus life plot with an R2 correlation of 0.94, and shows significantly lower correlation when known variations in yield strength, stress concentration factor, or residual stress are not included in the model input, thus demonstrating the model sensitivity to these variables.

Sign in / Sign up

Export Citation Format

Share Document