In Plane Mechanical Properties of Tetrachiral and Antitetrachiral Hybrid Metastructures

2017 ◽  
Vol 84 (8) ◽  
Author(s):  
Huimin Li ◽  
Yongbin Ma ◽  
Weibin Wen ◽  
Wenwang Wu ◽  
Hongshuai Lei ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Strain Energy ◽  
Energy Analysis ◽  
Poisson Ratio ◽  
Theoretical Models ◽  
Uniaxial Tensile ◽  
Geometrical Parameters ◽  
Element Simulation ◽  
Ring Rotation ◽  
Anisotropic Mechanical Properties

A novel tetrachiral and antitetrachiral hybrid metastructure is proposed, and its in-plane mechanical properties are studied through strain energy analysis. Based on rigid ring rotation assumption, the analytical expression for the in-plane modulus of anisotropic tetrachiral and antitetrachiral hybrid metastructure is derived, and in-plane tensile experimental test and finite element simulation are performed and compared with the theoretical models. The corresponding in-plane anisotropic mechanical properties can be tuned with three independent dimensionless geometrical parameters, and effects of dimensionless geometrical parameters on the in-plane mechanical properties are studied systematically. Finally, an innovative tetrachiral and antitetrachiral hybrid metastructure stent is designed, and its mechanical behaviors under uniaxial tensile loading are investigated. It is found that the designed tetrachiral and antitetrachiral hybrid stent shows negative Poisson ratio properties, and the axial and circumferential deformation can be controlled through adjusting the spacing of unit cell along axial and circumferential directions.

scholarly journals Digital volume correlation analysis of polylactic acid based fused filament fabrication printed composites

2021 ◽  
pp. 002199832110205
Author(s):  
Cristofaro S Timpano ◽  
Garrett W Melenka
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Measurement Techniques ◽  
Strain Tensor ◽  
Uniaxial Tensile ◽  
Digital Volume Correlation ◽  
Tensor Fields ◽  
Fused Filament Fabrication ◽  
Study Results ◽  
Anisotropic Mechanical Properties

Fused filament fabrication (FFF) has rapidly begun to see implementation in industrial fields as a method of rapid manufacturing. Traditional FFF parts are made from a single thermoplastic polymer. The polymer is heated to its melting point and deposited on a work bed where a model is gradually built from the base up. While traditional FFF parts have low mechanical properties, a reinforcing phase allows for improved mechanical properties. The addition of a reinforcing material to the base polymer and complex internal microstructure of the 3 D printed party leads to anisotropic mechanical properties. Thus, these materials’ mechanical properties become challenging to characterize using traditional measurement techniques due to the previously mentioned factors. Therefore, it is essential to develop a method in which mechanical properties can be measured and analyzed. This study aims to characterize the mechanical behaviour under a uniaxial tensile load of an FFF produced polylactic acid (PLA)-copper particulate composite. The internal response of the FFF sample was imaged using micro-computed tomography at predetermined loads. The μ-CT images were input into an open-source digital volume correlation (DVC) software to measure the internal displacements and strain tensor fields. The study results show the development of different strain fields and interior features of the FFF parts.

Directional, Regional, and Layer Variations of Mechanical Properties of Esophageal Tissue and its Interpretation Using a Structure-Based Constitutive Model

2005 ◽  
Vol 128 (3) ◽  
pp. 409-418 ◽  
Author(s):  
W. Yang ◽  
T. C. Fung ◽  
K. S. Chian ◽  
C. K. Chong
Keyword(s):  
Mechanical Properties ◽  
Constitutive Model ◽  
Mechanical Behavior ◽  
Soft Tissues ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Material Parameters ◽  
Esophageal Tissue ◽  
Anisotropic Mechanical Properties ◽  
Mucosal Layer

The esophagus, like other soft tissues, exhibits nonlinear and anisotropic mechanical properties. As a composite structure, the properties of the outer muscle and inner mucosal layer are different. It is expected that the complex mechanical properties will induce nonhomogeneous stress distributions in the wall and nonuniform tissue remodeling. Both are important factors which influence the function of mechanosensitive receptor located in various layers of the wall. Hence, the characterization of the mechanical properties is essential to understand the neuromuscular motion of the esophagus. In this study, the uniaxial tensile tests were conducted along two mutually orthogonal directions of porcine esophageal tissue to identify the directional (circumferential and axial), regional (abdominal, thoracic, and cervical), and layer (muscle and mucosa) variations of the mechanical properties. A structure-based constitutive model, which took the architectures of the tissue’s microstructures into account, was applied to describe the mechanical behavior of the esophagus. Results showed that the constitutive model successfully described the mechanical behavior and provided robust estimates of the material parameters. In conclusion, the model was demonstrated to be a good descriptor of the mechanical properties of the esophagus and it was able to facilitate the directional, layer, and regional comparisons of the mechanical properties in terms of the associated material parameters.

scholarly journals Experimental and Numerical Evaluation of Mechanical Properties of 3D-Printed Stainless Steel 316L Lattice Structures

2021 ◽  
Author(s):  
M. Carraturo ◽  
G. Alaimo ◽  
S. Marconi ◽  
E. Negrello ◽  
E. Sgambitterra ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Mechanical Behavior ◽  
Numerical Simulations ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Lattice Structures ◽  
Stainless Steel 316L ◽  
Research Attention ◽  
Octet Truss

AbstractAdditive manufacturing (AM), and in particular selective laser melting (SLM) technology, allows to produce structural components made of lattice structures. These kinds of structures have received a lot of research attention over recent years due to their capacity to generate easy-to-manufacture and lightweight components with enhanced mechanical properties. Despite a large amount of work available in the literature, the prediction of the mechanical behavior of lattice structures is still an open issue for researchers. Numerical simulations can help to better understand the mechanical behavior of such a kind of structure without undergoing long and expensive experimental campaigns. In this work, we compare numerical and experimental results of a uniaxial tensile test for stainless steel 316L octet-truss lattice specimen. Numerical simulations are based on both the nominal as-designed geometry and the as-build geometry obtained through the analysis of µ-CT images. We find that the use of the as-build geometry is fundamental for an accurate prediction of the mechanical behavior of lattice structures.

Experimental investigation of the mechanical behavior of glass fiber/high fluidity polyamide-based composites for automotive market

2021 ◽  
pp. 073168442110140
Author(s):  
Hossein Ramezani-Dana ◽  
Moussa Gomina ◽  
Joël Bréard ◽  
Gilles Orange
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Mechanical Performance ◽  
Physical And Mechanical Properties ◽  
Ultimate Strain ◽  
Uniaxial Tensile ◽  
Compression Tests ◽  
Automotive Market ◽  
Glass Fiber Reinforced ◽  
Glass Fiber Reinforcement

In this work, we examine the relationships between the microstructure and the mechanical properties of glass fiber–reinforced polyamide 6,6 composite materials ( V f = 54%). These materials made by thermocompression incorporate different grades of high fluidity polyamide-based polymers and two types of quasi-UD glass fiber reinforcement. One is a classic commercial fabric, while the other specially designed and manufactured incorporates weaker tex glass yarns (the spacer) to increase the planar permeability of the preform. The effects of the viscosity of the polymers and their composition on the wettability of the reinforcements were analyzed by scanning electron microscopy observations of the microstructure. The respective influences of the polymers and the spacer on the mechanical performance were determined by uniaxial tensile and compression tests in the directions parallel and transverse to the warp yarns. Not only does the spacer enhance permeability but it also improves physical and mechanical properties: tensile longitudinal Young’s modulus increased from 38.2 GPa to 42.9 GPa (13% growth), tensile strength increased from 618.9 MPa to 697 MPa (3% growth), and decrease in ultimate strain from 1.8% to 1.7% (5% reduction). The correlation of these results with the damage observed post mortem confirms those acquired from analyses of the microstructure of composites and the rheological behaviors of polymers.

scholarly journals Water Influence on the Uniaxial Tensile Behavior of Polytetrafluoroethylene-Coated Glass Fiber Fabric

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 846
Author(s):  
Hastia Asadi ◽  
Joerg Uhlemann ◽  
Natalie Stranghoener ◽  
Mathias Ulbricht
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Operation Time ◽  
Uniaxial Tensile ◽  
Membrane Structures ◽  
Strength Deterioration ◽  
Coated Glass ◽  
Reversible Loss ◽  
The Impact ◽  
Loss Of Strength

Polytetrafluoroethylene (PTFE)-coated glass fiber fabrics are used for long-lasting membrane structures due to their outstanding mechanical properties, chemical stabilities, and satisfying service life. During their operation time, different environmental impacts might influence their performance, especially regarding the mechanical properties. In this contribution, the impact of water on the tensile strength deterioration was assessed experimentally, providing evidence of considerable but partially reversible loss of strength by up to 20% among the various types of investigated industrially established fabrics.

Comprehensive study on mechanical properties of coated biaxial warp-knitted fabrics

2021 ◽  
pp. 073168442110204
Author(s):  
Bin Yang ◽  
Yingying Shang ◽  
Zeliang Yu ◽  
Minger Wu ◽  
Youji Tao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Failure Modes ◽  
Least Squares Method ◽  
Tensile Tests ◽  
Tensile Creep ◽  
Base Layer ◽  
Sustained Load ◽  
Uniaxial Tensile ◽  
Membrane Structures ◽  
Knitted Fabrics

In recent years, coated fabrics have become the major material used in membrane structures. Due to the special structure of base layer and mechanical properties, coated biaxial warp-knitted fabrics are increasingly applied in pneumatic structures. In this article, the mechanical properties of coated biaxial warp-knitted fabrics are investigated comprehensively. First, off-axial tensile tests are carried out in seven in-plane directions: 0°, 15°, 30°, 45°, 60°, 75°, and 90°. Based on the stress–strain relationship, tensile strengths are obtained and failure modes are studied. The adaptability of Tsai–Hill criterion is analyzed. Then, the uniaxial tensile creep test is performed under 24-h sustained load and the creep elongation is calculated. Besides, tearing strengths in warp and weft directions are obtained by tearing tests. Finally, the biaxial tensile tests under five different load ratios of 1:1, 2:1, 1:2, 1:0, and 0:1 are carried out, and the elastic constants and Poisson’s ratio are calculated using the least squares method based on linear orthotropic assumption. Moreover, biaxial specimens under four load ratios of 3:1, 1:3, 5:1, and 1:5 are further tensile tested to verify the adaptability of linear orthotropic model. These experimental data offer a deeper and comprehensive understanding of mechanical properties of coated biaxial warp-knitted fabrics and could be conveniently adopted in structural design.

scholarly journals Investigation of Damage Evolution in Heterogeneous Rock Based on the Grain-Based Finite-Discrete Element Model

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3969
Author(s):  
Shirui Zhang ◽  
Shili Qiu ◽  
Pengfei Kou ◽  
Shaojun Li ◽  
Ping Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Grain Orientation ◽  
Damage Evolution ◽  
Discrete Element ◽  
Uniaxial Tensile ◽  
Tensile Cracks ◽  
Rock Heterogeneity ◽  
Heterogeneous Rock

Granite exhibits obvious meso-geometric heterogeneity. To study the influence of grain size and preferred grain orientation on the damage evolution and mechanical properties of granite, as well as to reveal the inner link between grain size‚ preferred orientation, uniaxial tensile strength (UTS) and damage evolution, a series of Brazilian splitting tests were carried out based on the combined finite-discrete element method (FDEM), grain-based model (GBM) and inverse Monte Carlo (IMC) algorithm. The main conclusions are as follows: (1) Mineral grain significantly influences the crack propagation paths, and the GBM can capture the location of fracture section more accurately than the conventional model. (2) Shear cracks occur near the loading area, while tensile and tensile-shear mixed cracks occur far from the loading area. The applied stress must overcome the tensile strength of the grain interface contacts. (3) The UTS and the ratio of the number of intergrain tensile cracks to the number of intragrain tensile cracks are negatively related to the grain size. (4) With the increase of the preferred grain orientation, the UTS presents a “V-shaped” characteristic distribution. (5) During the whole process of splitting simulation, shear microcracks play the dominant role in energy release; particularly, they occur in later stage. This novel framework, which can reveal the control mechanism of brittle rock heterogeneity on continuous-discontinuous trans-scale fracture process and microscopic rock behaviour, provides an effective technology and numerical analysis method for characterizing rock meso-structure. Accordingly, the research results can provide a useful reference for the prediction of heterogeneous rock mechanical properties and the stability control of engineering rock masses.

Sign in / Sign up

Export Citation Format

Share Document