Numerical Study on Conjugated Laminar Mixed Convection of Alumina/Water Nanofluid Flow, Heat Transfer, and Entropy Generation Within a Tube-on-Sheet Flat Plate Solar Collector

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Mohammad Charjouei Moghadam ◽  
Mojtaba Edalatpour ◽  
Juan P. Solano
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Entropy Generation ◽  
Solar Collector ◽  
Richardson Number ◽  
Volume Concentration ◽  
Volume Fraction ◽  
Flat Plate Solar Collector

In this research, an inclined three-dimensional nanofluid-based tube-on-sheet flat plate solar collector (FPSC) working under laminar conjugated mixed convection heat transfer is numerically modeled. The working fluid is selected to be alumina/water (Al2O3/water) and results from heat transfer, entropy generation, and pressure drop points of view are being presented for various prominent parameters, namely volume fraction, nanoparticles diameter, Richardson and Reynolds numbers. According to the simulations, Nusselt number decreases as the Richardson number or volume fraction of the nanofluid rises, whereas heat transfer coefficient experiences an augmentation when volume concentration and the Richardson number surge. Also, data reveal that total entropy generation rate of the system declines when the alumina/water nanofluid is utilized inside the system as the volume fraction or the Richardson number increases. Additionally, it is found that increasing the nanoparticle volume concentration or the Richardson number diminishes the pressure drop considerably, whereas friction factor substantially proliferates as the Richardson number or volume fraction rises. Eventually, employment of larger alumina nanoparticles mean diameter eventuates in providing lower Nusselt number and apparent friction factor while it increases the pressure drop and heat transfer coefficient. Finally, comparing the efficiency of the presented FPSC design with those available in the literature shows a superior performance by the present design with its maximum occurring at 2 vol %.

Heat Transfer, Pressure Drop, and Entropy Generation in a Solar Collector Using SiO2/Water Nanofluids: Effects of Nanoparticle Size and pH

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Omid Mahian ◽  
Ali Kianifar ◽  
Ahmet Z. Sahin ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Entropy Generation ◽  
Thermal Efficiency ◽  
Solar Collector ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Transfer Pressure

In this paper, an analytical study is carried out on the heat transfer, pressure drop, and entropy generation in a flat-plate solar collector using SiO2/water nanofluid with volume concentration of 1%. In the study, the effects of two different values of pH, i.e., 5.8 and 6.5, and two different sizes of nanoparticles, i.e., 12 nm and 16 nm, on the entropy generation rate in turbulent flow are investigated. The results are compared with the results obtained for the case of water. The findings show that by using the Brinkman model to calculate the viscosity instead of experimental data one obtains a higher heat transfer coefficient and thermal efficiency than that in the case of water, while, when the experimental data are used, the heat transfer coefficient and thermal efficiency of water are found to be higher than that of nanofluids. The results reveal that using nanofluids increases the outlet temperature and reduces the entropy generation rate. It is also found that for nanofluids containing the particles with a size of 16 nm, the increase in pH value would increase the entropy generation rate, while for nanoparticles with a size of 12 nm the increase in pH would decrease the entropy generation.

scholarly journals Application of Nanofluids in Thermal Performance Enhancement of Parabolic Trough Solar Collector: State-of-the-Art

2019 ◽  
Vol 9 (3) ◽  
pp. 463 ◽  
Author(s):  
Hamed Olia ◽  
Mohammadamin Torabi ◽  
Mehdi Bahiraei ◽  
Mohammad Hossein Ahmadi ◽  
Marjan Goodarzi ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Entropy Generation ◽  
Thermal Efficiency ◽  
Performance Enhancement ◽  
Volume Fraction ◽  
Working Fluid ◽  
Parabolic Trough

The present review paper aims to document the latest developments on the applications of nanofluids as working fluid in parabolic trough collectors (PTCs). The influence of many factors such as nanoparticles and base fluid type as well as volume fraction and size of nanoparticles on the performance of PTCs has been investigated. The reviewed studies were mainly categorized into three different types of experimental, modeling (semi-analytical), and computational fluid dynamics (CFD). The main focus was to evaluate the effect of nanofluids on thermal efficiency, entropy generation, heat transfer coefficient enhancement, as well as pressure drop in PTCs. It was revealed that nanofluids not only enhance (in most of the cases) the thermal efficiency, convection heat transfer coefficient, and exergy efficiency of the system but also can decrease the entropy generation of the system. The only drawback in application of nanofluids in PTCs was found to be pressure drop increase that can be controlled by optimization in nanoparticles volume fraction and mass flow rate.

Effect of Nanofluid on Heat Transfer Enhancement for Mixed Convection Flow Over a Corrugated Surface

2020 ◽  
Vol 45 (4) ◽  
pp. 373-383
Author(s):  
Nepal Chandra Roy ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Local Nusselt Number ◽  
Richardson Number ◽  
Thermal Boundary Layer ◽  
Volume Fraction ◽  
Convection Flow ◽  
Mixed Convection Flow

AbstractA mathematical model for mixed convection flow of a nanofluid along a vertical wavy surface has been studied. Numerical results reveal the effects of the volume fraction of nanoparticles, the axial distribution, the Richardson number, and the amplitude/wavelength ratio on the heat transfer of Al2O3-water nanofluid. By increasing the volume fraction of nanoparticles, the local Nusselt number and the thermal boundary layer increases significantly. In case of \mathrm{Ri}=1.0, the inclusion of 2 % and 5 % nanoparticles in the pure fluid augments the local Nusselt number, measured at the axial position 6.0, by 6.6 % and 16.3 % for a flat plate and by 5.9 % and 14.5 %, and 5.4 % and 13.3 % for the wavy surfaces with an amplitude/wavelength ratio of 0.1 and 0.2, respectively. However, when the Richardson number is increased, the local Nusselt number is found to increase but the thermal boundary layer decreases. For small values of the amplitude/wavelength ratio, the two harmonics pattern of the energy field cannot be detected by the local Nusselt number curve, however the isotherms clearly demonstrate this characteristic. The pressure leads to the first harmonic, and the buoyancy, diffusion, and inertia forces produce the second harmonic.

Heat Transfer Performance of Different Nanofluids Flows in a Helically Coiled Heat Exchanger

2013 ◽  
Vol 832 ◽  
pp. 160-165 ◽  
Author(s):  
Mohammad Alam Khairul ◽  
Rahman Saidur ◽  
Altab Hossain ◽  
Mohammad Abdul Alim ◽  
Islam Mohammed Mahbubul
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Transfer Performance

Helically coiled heat exchangers are globally used in various industrial applications for their high heat transfer performance and compact size. Nanofluids can provide excellent thermal performance of this type of heat exchangers. In the present study, the effect of different nanofluids on the heat transfer performance in a helically coiled heat exchanger is examined. Four different types of nanofluids CuO/water, Al2O3/water, SiO2/water, and ZnO/water with volume fractions 1 vol.% to 4 vol.% was used throughout this analysis and volume flow rate was remained constant at 3 LPM. Results show that the heat transfer coefficient is high for higher particle volume concentration of CuO/water, Al2O3/water and ZnO/water nanofluids, while the values of the friction factor and pressure drop significantly increase with the increase of nanoparticle volume concentration. On the contrary, low heat transfer coefficient was found in higher concentration of SiO2/water nanofluids. The highest enhancement of heat transfer coefficient and lowest friction factor occurred for CuO/water nanofluids among the four nanofluids. However, highest friction factor and lowest heat transfer coefficient were found for SiO2/water nanofluids. The results reveal that, CuO/water nanofluids indicate significant heat transfer performance for helically coiled heat exchanger systems though this nanofluids exhibits higher pressure drop.

scholarly journals Study of convection heat transfer enhancement inside lid driven cavity utilizing fins and nanofluid

2017 ◽  
Vol 21 (6 Part A) ◽  
pp. 2431-2442
Author(s):  
Arash Lavasani ◽  
Mousa Farhadi ◽  
Darzi Rabienataj
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Richardson Number ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Thermal Conductivity Ratio ◽  
Convection Flow ◽  
Driven Cavity ◽  
Ratio Change ◽  
Hot Surface

In the present study, the effect of suspension of nanoparticle on mixed convection flow is investigated numerically in lid driven cavity with fins on its hot surface. Study is carried out for Richardson numbers ranging from 0.1 to 10, fin(s) height ratio change from 0.05 to 0.15 and volume fraction of nanoparticles from 0 to 0.03, respectively. The thermal conductivity ratio (kfin/kf) is equal to 330 and Grashof number is assumed to be constant (104) so that the Richardson numbers changes with Reynolds number. Results show that the heat transfer enhances by using nanofluid for all studied Richardson numbers. Adding fins on hot wall has different effects on heat transfer depend to Richardson number and height of fins. Use of low height fin in flow with high Richardson number enhances the heat transfer rate while by increasing the height of fin the heat transfer reduces even lower than it for pure fluid. The overall enhancement in Nusselt number by adding 3% nanoparticles and 3 fins is 54% at Ri=10. They cause reduction of Nusselt Number by 25% at Ri=0.1. Higher fins decrease the heat transfer due to blocking fluid at corners of fins.

scholarly journals Mixed Convection and Entropy Generation of an Ag-Water Nanofluid in an Inclined L-Shaped Channel

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 1150 ◽  
Author(s):  
Taher Armaghani ◽  
Muneer Ismael ◽  
Ali Chamkha ◽  
Ioan Pop
Keyword(s):  
Nusselt Number ◽  
Mixed Convection ◽  
Entropy Generation ◽  
Richardson Number ◽  
Volume Fraction ◽  
Governing Equations ◽  
Nanoparticles Volume Fraction ◽  
The Mean ◽  
The Right ◽  
Volume Method

This paper investigates the mixed convection and entropy generation of an Ag-water nanofluid in an L-shaped channel fixed at an inclination angle of 30° to the horizontal axis. An isothermal heat source was positioned in the middle of the right inclined wall of the channel while the other walls were kept adiabatic. The finite volume method was used for solving the problem’s governing equations. The numerical results were obtained for a range of pertinent parameters: Reynolds number, Richardson number, aspect ratio, and the nanoparticles volume fraction. These results were Re = 50–200; Ri = 0.1, 1, 10; AR = 0.5–0.8; and φ = 0.0–0.06, respectively. The results showed that both the Reynolds and the Richardson numbers enhanced the mean Nusselt number and minimized the rate of entropy generation. It was also found that when AR. increased, the mean Nusselt number was enhanced, and the rate of entropy generation decreased. The nanoparticles volume fraction was predicted to contribute to increasing both the mean Nusselt number and the rate of entropy generation.

Convective Heat Transfer Coefficient and Pressure Drop of Al2O3-Water Nanofluid in a Single-Phase Microchannel for Cooling of High Heat Output Devices

2008 ◽  
Author(s):  
Guillermo E. Valencia ◽  
Miguel A. Ramos ◽  
Antono J. Bula
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Convective Heat Transfer Coefficient ◽  
Heat Output ◽  
Flux Boundary Condition

The paper describes an experimental procedure performed to obtain the convective heat transfer coefficient of Al2O3 nanofluid working as cooling fluid under turbulent regimen through arrays of aluminum microchannel heat sink having a diameter of 1.2 mm. Experimental Nusselt number correlation as a function of the volume fractions, Reynolds, Peclet and Prandtl numbers for a constant heat flux boundary condition is presented. The correlation for Nusselt number has a good agreement with experimental data and can be used to predict heat transfer coefficient for this specific nanofluid, water/Al2O3. Furthermore, the pressure drop is also analyzed considering the different nanoparticles concentration.

Lower Entropy Generation in Microchannels With Laminar Single Phase Flow

2010 ◽  
Author(s):  
E. Galvis ◽  
J. R. Culham
Keyword(s):  
Heat Transfer ◽  
Boundary Condition ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Entropy Generation ◽  
Entropy Generation Rate ◽  
Channel Geometry ◽  
Micro Channels ◽  
Optimum Channel

In this study the entropy generation minimization method is used to find the optimum channel dimensions in micro heat exchangers with a uniform heat flux. With this approach, pressure drop and heat transfer in the micro channels are considered simultaneously during the optimization analysis. A computational model is developed to find the optimum channel depth knowing other channel geometry dimensions and coolant inlet properties. The flow is assumed laminar and both hydrodynamically and thermally fully developed and incompressible. However, to take into account the effect of the developing length in the friction losses, the Hagenbach’s factor is introduced. The micro channels are assumed to have an isothermal or isoflux boundary condition, non-slip flow, and fluid properties have dependency on temperature accordingly. For these particular case studies, the pressure drop and heat transfer coefficient for the isoflux boundary condition is higher than the isothermal case. Higher heat transfer coefficient and pressure drop were found when the channel size decreased. The optimum channel geometry that minimizes the entropy generation rate tends to be a deep, narrow channel.

Sign in / Sign up

Export Citation Format

Share Document