Two-Phase Analysis on the Conjugate Heat Transfer Performance of Microchannel With Cu, Al, SWCNT, and Hybrid Nanofluids

2017 ◽  
Vol 9 (4) ◽  
Author(s):  
Rajesh Nimmagadda ◽  
K. Venkatasubbaiah
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Base Fluid ◽  
Average Nusselt Number ◽  
Conjugate Heat Transfer ◽  
Pure Water ◽  
Heat Transfer Characteristics ◽  
Two Phase ◽  
Transfer Characteristics ◽  
Hybrid Nanofluids

This numerical study has been carried out by developing two-phase mixture model with conjugate heat transfer. Pure and hybrid nanofluids (HyNF) with particle as well as base fluid hybridization are used in analyzing the performance of microchannel under forced convection laminar flow. The flow as well as heat transfer characteristics of pure water, copper (Cu), aluminum (Al), single-walled carbon nanotube (SWCNT), and hybrid (Cu + Al, water + methanol) nanofluids with various nanoparticle volume concentrations at different Reynolds numbers are reported. Sphericity-based effective thermal conductivity evaluation is considered in the case of SWCNT nanofluids by using volume and surface area of nanotubes. A significant enhancement in the average Nusselt number is observed numerically for both pure and hybrid nanofluids. Pure nanofluids such as Al, Cu, and SWCNT with 3 vol % nanoparticle concentration enhanced the average Nusselt number by 21.09%, 32.46%, and 71.25% in comparison with pure water at Re = 600. Whereas, in the case of hybrid nanofluids such as 3 vol % HyNF (0.6% Cu + 2.4% Al) and 3 vol % SWCNT (20% Me + 80% PW), the enhancement in average Nusselt number is observed to be 23.38% and 46.43% in comparison with pure water at Re = 600. The study presents three equivalent combinations of nanofluids (1 vol % Cu and 0.5 vol % SWCNT), (2 vol % Cu, 1 vol % SWCNT and 3 vol % HyNF (0.6% Cu + 2.4% Al)) as well as (2 vol % SWCNT and 3 vol % SWCNT (20% Me + 80% PW)) that provides a better switching option in choosing efficient working fluid with minimum cost based on cooling requirement. The study also shows that by dispersing SWCNT nanoparticles, one can enhance the heat transfer characteristics of base fluid containing methanol as antifreeze. The conduction phenomena of solid region cause the interface temperature between solid as well as fluid regions to increase along the length of the microchannel. The developed numerical model is validated with the numerical and experimental results available in the literature.

Heat transfer characteristics of nanofluids from a sinusoidal corrugated cylinder placed in a square cavity

2021 ◽  
pp. 095440622110272
Author(s):  
Salaika Parvin ◽  
Nepal Chandra Roy ◽  
Litan Kumar Saha ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Average Nusselt Number ◽  
Numerical Study ◽  
Heat Transfer Characteristics ◽  
Number Range ◽  
Transfer Characteristics ◽  
Wide Range

A numerical study is performed to investigate nanofluids' flow field and heat transfer characteristics between the domain bounded by a square and a wavy cylinder. The left and right walls of the cavity are at constant low temperature while its other adjacent walls are insulated. The convective phenomena take place due to the higher temperature of the inner corrugated surface. Super elliptic functions are used to transform the governing equations of the classical rectangular enclosure into a system of equations valid for concentric cylinders. The resulting equations are solved iteratively with the implicit finite difference method. Parametric results are presented in terms of streamlines, isotherms, local and average Nusselt numbers for a wide range of scaled parameters such as nanoparticles concentration, Rayleigh number, and aspect ratio. Several correlations have been deduced at the inner and outer surface of the cylinders for the average Nusselt number, which gives a good agreement when compared against the numerical results. The strength of the streamlines increases significantly due to an increase in the aspect ratio of the inner cylinder and the Rayleigh number. As the concentration of nanoparticles increases, the average Nusselt number at the internal and external cylinders becomes stronger. In addition, the average Nusselt number for the entire Rayleigh number range gets enhanced when plotted against the volume fraction of the nanofluid.

The Effect of Channel Diameter on Heat Transfer Characteristics of Two-Phase Flow in Microchannels

2011 ◽  
Author(s):  
Kyosung Choo ◽  
Daniel Trainer ◽  
Sung Jin Kim
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Gas Flow ◽  
Two Phase Flow ◽  
Superficial Velocity ◽  
Phase Flow ◽  
Heat Transfer Characteristics ◽  
Two Phase ◽  
Channel Diameter ◽  
Transfer Characteristics

The heat transfer and fluid flow characteristics of non-boiling two-phase flow in microchannels were experimentally investigated. The effects of channel diameter (140, 222, 334, and 506 μm) on the Nusselt number were considered. Air and water were used as the working fluids. Results were presented for the Nusselt number over a wide range of gas superficial velocity (1.24–40.1 m/s), liquid superficial velocity (0.57–2.13 m/s), and wall heat flux (0.34–0.95 MW/m2). The results showed that the Nusselt number increased with increasing gas flow rate for the 506 μm and 334 μm channels, while the Nusselt number decreased with increasing gas flow for the 222 μm and 140 μm channels. Based on these experimental results, a transition channel diameter of about 235 μm to 260 μm, which distinguishes microchannels from minichannels, was suggested. By observing two-phase flow patterns within the microchannels, viscosity and surface tension were identified as the key factors that caused the heat transfer characteristics to change. In addition, new correlations for the forced convection Nusselt number were developed.

Numerical Study on Flow and Heat Transfer Characteristics of Jet Impingement

2011 ◽  
Author(s):  
Xinjun Wang ◽  
Rui Liu ◽  
Xiaowei Bai ◽  
Jinling Yao
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Jet Impingement ◽  
Target Surface ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

A mathematical model used for studying jet impingement cooling characteristics is established, and the rationality of the calculation model and method is confirmed by the experimental data. The CFX software is used to numerically simulate the jet impingement cooling characteristics on a gas turbine blade. The effects of various parameters, such as the arrays of impinging nozzles, the jet Reynolds number, the jet-to-jet distance, the ratio of nozzle-to-surface spacing to jet diameter H/d, and the radius of curvature of the target surface, on the flow and heat transfer characteristics of a impingement cooling process are studied. The results indicate that the impingement jets can make complex vortex in the cooling channel, the flow boundary layer is extremely thin and highly turbulent. Underneath each impingement nozzle, there will appear a low temperature area and a peak of Nusselt number on the impingement target surface, the distribution of temperature and Nusselt number on the target surface are associated with arrangement of impingement nozzles. The average Nusselt number of the in-line arrangement nozzles is higher than that of the staggered arrangement ones. With the increasing of jet Reynolds number, the velocity impinging on the target surface and Nusselt number increase. However, heat transfer of impingement cooling on target surface is not sensitive to the jet nozzles distance; the velocity impinging on the target surface and Nusselt number decrease with the increasing of the H/d value. For the curved target surface cases, the average Nusselt number of the target surface and the effect of heat transfer decreased with the increasing of curvature radius R.

scholarly journals Experimental Investigation of Single-Phase Liquid Flow and Heat Transfer in Multiport Minichannels

2014 ◽  
Author(s):  
Mesru Altinoz ◽  
Almila Guvenc Yazicioglu ◽  
Derek Baker
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Single Phase ◽  
Hydraulic Diameter ◽  
Heat Transfer Characteristics ◽  
Flux Boundary Condition ◽  
Transfer Characteristics ◽  
Area Of Interest ◽  
Poiseuille Number

Small channels have been an area of interest since the 1970s owing to their enhanced heat transfer characteristics. However a wide number of studies in literature show inconsistent results. In this work, an experimental set-up has been designed and constructed to investigate pressure drop and heat transfer characteristics of single-phase water flow in rectangular multiport minichannels. Laminar flow inside three minichannels with different hydraulic diameters and different port numbers were examined under a constant heat flux boundary condition. The results are presented in terms of Poiseuille number (Po) and average Nusselt number (Nu). Generally, average Nusselt number results and Poiseuille number results showed good agreement with constant Po theory and constant Nu theory, excluding developing effects and experimental errors. On the other hand, developing effects are found to be increasing as hydraulic diameter decreases. Similarly, constant Nu value showed a decrease with increasing hydraulic diameter. The experimental results are compared with conventional correlations. While the agreement with conventional correlations is satisfactory, the predictions of the correlations overestimated most of the results. No early transition was observed for Reynolds number (Re) smaller than 1800.

Thermal Optimal Design for Heat Sinks or Heat Sink/TEC Assemblies in a Ducted Flow

2007 ◽  
Author(s):  
T. Y. Wu ◽  
M. C. Wu ◽  
J. T. Horng ◽  
S. F. Chang ◽  
P. L. Chen ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Optimal Design ◽  
Thermal Resistance ◽  
Heat Sink ◽  
Average Nusselt Number ◽  
Heat Sinks ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Starting Point

A series of experimental studies on the heat transfer characteristics from heat sinks or Heat Sink/TEC assemblies in a ducted flow have been performed. Their effects on heat transfer characteristics in ducted flow have been systematically explored. From the results, new performance correlations of the temperature difference (ΔT) and terminal voltage (V) of the TEC modules are proposed. Besides, two new correlations of steady-state average Nusselt number and external thermal resistance in terms of relevant influencing parameters for confined ppf heat sinks in a ducted flow are also proposed, respectively. The statistical sensitivity analysis of ANOVA F-test is employed to estimate the contributions of relevant parameters. Furthermore, a series of RSM models for evaluating heat transfer characteristics including average Nusselt number, average external thermal resistance and Tc−Ta are established. A Sequential Quadratic Programming with multi-starting-point method is successfully employed to automatically and efficiently seek a globally optimal thermal performance. An optimal design of HS/TEC assemblies under both COP ≥ 2 and pumping power limitation larger than 30 W can be achieved with a reduction of 75% on thermal resistance.

Pressure Drop and Heat Transfer Characteristics for Partially-Confined Heat Sinks in Ducted Flow

2006 ◽  
Author(s):  
H. T. Chen ◽  
T. Y. Wu ◽  
P. L. Chen ◽  
S. F. Chang ◽  
Y. H. Hung
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Heat Sink ◽  
Average Nusselt Number ◽  
Heat Sinks ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Effective Friction

The pressure drop and heat transfer characteristics for partially-confined heat sinks with different fin types, including plain-plate fin, pin-fin array and strip-fin array, in ducted flow are investigated. The main focus of the experimental results is on pressure drop and heat transfer characteristics of generalized heat sink in ducted flow with considering the flow top- and side-bypass effects. The parameters controlled in the study are the heating load (Qt), inlet flow velocity (Ui), the ratio of heat sink height to duct height (Hs/Hc), and the ratio of heat sink width to duct width (Ws/Wc). The ranges of parameters studied are Ui=2~12m/s, Qt=10~30W, Ws/Wc = 0.6~1, and Hs/Hc = 0.5~1. In the present study, an effective friction factor related to the overall pressure drop is defined; and a new experimental correlation for the effective friction factor for generalized heat sinks in ducted flow with top- and side-bypass effects is presented. A satisfactory agreement between the experimental data and the theoretical predictions is achieved with the maximum and average deviations of 17.2% and 9.6%, respectively. As for convective heat transfer performance, the average Nusselt number is not significantly affected by Grashof number; while, it increases significantly with increasing Reynolds number. Furthermore, the thermal performance increases with increasing top or side confinement ratio (Hs/Hc or Ws/Wc). The best thermal performance occurred at the fully-confined condition, i.e., Hs/Hc=1, Ws/Wc = 1. Based on all the experimental data for three types of partially-confined heat sinks, a generalized correlation of average Nusselt number for partially-confined heat sinks in ducted flow in terms of Re, Hs/Hc and Ws/Wc is presented. The maximum and average deviations of the results obtained by the experimental data from the theoretical prediction are 12.4% and 7.5%, respectively.

Forced Convection in Cross Flow of Power Law Fluids Over a Pair of Circular Cylinder in Tandem Arrangement

2008 ◽  
Author(s):  
Rahul C. Patil ◽  
Ram P. Bharti ◽  
Raj P. Chhabra
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Forced Convection ◽  
Power Law ◽  
Average Nusselt Number ◽  
Cross Flow ◽  
Heat Transfer Characteristics ◽  
Tandem Arrangement ◽  
Transfer Characteristics ◽  
Power Law Fluids

Forced convection heat transfer characteristics for the flow of incompressible power law fluids over a pair of cylinders (of equal diameters) in tandem arrangement have been studied numerically in the two-dimensional, steady cross-flow regime. The field equations have been solved using a finite volume method based solver (FLUENT 6.2) over the ranges of conditions as follows: power law index (n = 0.4, 1, 1.8), Reynolds number (Re = 1, 40), Prandtl number (Pr = 1, 100), the gap between the two cylinders (G = 2) and for two thermal boundary conditions, namely constant temperature or heat flux prescribed on the surface of the two cylinders. While the upstream cylinder shows heat transfer characteristics similar to that of an isolated cylinder, the downstream cylinder displays a complex dependence on the relevant dimensionless parameters. Both the wake interference and power-law rheology influence the heat transfer characteristics to varying extents. Generally, the upstream cylinder shows higher values of the average Nusselt number than the downstream cylinder. However, the average Nusselt number values for both cylinders are seen to be smaller than that for a single cylinder otherwise under identical conditions. With reference to Newtonian fluids, the shear-thinning behaviour promotes heat transfer whereas shear-thickening lowers it.

scholarly journals Uncertainties Analysis on the Prediction of Flow and Heat Transfer of Liquid Sodium with CFD Technology

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Zhanwei Liu ◽  
Xinyu Li ◽  
Tenglong Cong ◽  
Rui Zhang ◽  
Lingyun Zheng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Liquid Sodium ◽  
Heat Transfer Characteristics ◽  
Backward Facing Step ◽  
Heating Wall ◽  
Transfer Characteristics ◽  
Cfd Models ◽  
Flow And Heat Transfer

The prediction of flow and heat transfer characteristics of liquid sodium with CFD technology is of significant importance for the design and safety analysis of sodium-cooled fast reactor. The accuracies and uncertainties of the CFD models should be evaluated to improve the confidence of the numerical results. In this work, the uncertainties from the turbulent model, boundary conditions, and physical properties for the flow and heat transfer of liquid sodium were evaluated against the experimental data. The results of uncertainty quantization show that the maximum uncertainties of the Nusselt number and friction coefficient occurred in the transition zone from the inlet to the fully developed region in the circular tube, while they occurred near the reattachment point in the backward-facing step. Furthermore, in backward-facing step flow, the maximum uncertainty of temperature migrated from the heating wall to the geometric center of the channel, while the maximum uncertainty of velocity occurred near the vortex zone. The results of sensitivity analysis illustrate that the Nusselt number was negatively correlated with the thermal conductivity and turbulent Prandtl number, while the friction coefficient was positively correlated with the density and Von Karman constant. This work can be a reference to evaluate the accuracy of the standard k-ε model in predicting the flow and heat transfer characteristics of liquid sodium.

Sign in / Sign up

Export Citation Format

Share Document