Aerothermal Performance of a Nozzle Vane Cascade With a Generic Nonuniform Inlet Flow Condition—Part II: Influence of Purge and Film Cooling Injection

2017 ◽  
Vol 139 (10) ◽  
Author(s):  
G. Barigozzi ◽  
H. Abdeh ◽  
A. Perdichizzi ◽  
M. Henze ◽  
J. Krueckels
Keyword(s):  
Thermal Performance ◽  
Film Cooling ◽  
Leading Edge ◽  
Axial Position ◽  
Intensity Level ◽  
Cooling Effectiveness ◽  
Inlet Flow ◽  
Film Cooling Effectiveness ◽  
Nozzle Vane ◽  
Flow Nonuniformity

In the present paper, the influence of the presence of an inlet flow nonuniformity on the aerodynamic and thermal performance of a film cooled linear nozzle vane cascade is fully assessed. Tests have been carried out with platform cooling, with coolant ejected through a slot located upstream of the leading edge. Cooling air is also ejected through a row of cylindrical holes located upstream of the slot, simulating a combustor cooling system. An obstruction was installed upstream of the cascade at variable tangential and axial position to generate a flow nonuniformity. The cascade was tested at a high inlet turbulence intensity level (Tu1 = 9%) and at a constant inlet Mach number of 0.12 and nominal cooling condition. Aerothermal characterization of vane platform was obtained through five-hole probe and end wall adiabatic film cooling effectiveness measurements. Results show a relevant negative impact of inlet flow nonuniformity on the cooled cascade aerodynamic and thermal performance. Higher film cooling effectiveness and lower aerodynamic losses are obtained when the inlet flow nonuniformity is located at midpitch, while lower effectiveness and higher losses are obtained when it is aligned to the vane leading edge. Moving the nonuniformity axially or changing its blockage only marginally influences the platform thermal protection.

Aero-Thermal Performance of a Nozzle Vane Cascade With a Generic Non Uniform Inlet Flow Condition: Part II — Influence of Purge and Film Cooling Injection

2016 ◽  
Author(s):  
G. Barigozzi ◽  
H. Abdeh ◽  
A. Perdichizzi ◽  
M. Henze ◽  
J. Krueckels
Keyword(s):  
Thermal Performance ◽  
Film Cooling ◽  
Cooling System ◽  
Leading Edge ◽  
Axial Position ◽  
Intensity Level ◽  
Cooling Effectiveness ◽  
Inlet Flow ◽  
Film Cooling Effectiveness ◽  
Nozzle Vane

In the present paper, the influence of the presence of an inlet flow non uniformity on the aerodynamic and thermal performance of a film cooled linear nozzle vane cascade is fully assessed. Tests have been carried out with platform cooling, with coolant ejected through a slot located upstream of the leading edge. Cooling air is also ejected through a row of cylindrical holes located upstream of the slot, simulating a combustor cooling system. An obstruction was installed upstream of the cascade at variable tangential and axial position to generate a flow non uniformity. The cascade was tested at a high inlet turbulence intensity level (Tu1 = 9%) and at a constant inlet Mach number of 0.12 and nominal cooling condition. Aero-thermal characterization of vane platform was obtained through 5-hole probe and end wall adiabatic film cooling effectiveness measurements. Results show a relevant negative impact of inlet flow non uniformity on the cooled cascade aerodynamic and thermal performance. Higher film cooling effectiveness and lower aerodynamic losses are obtained when the inlet flow non uniformity is located at mid pitch, while lower effectiveness and higher losses are obtained when it is aligned to the vane leading edge. Moving the non uniformity axially or changing its blockage only marginally influences the platform thermal protection.

Inlet Flow Incidence Effects on the Thermal Performance of Showerhead Cooling in a Nozzle Vane Cascade

2019 ◽  
Author(s):  
H. Abdeh ◽  
G. Barigozzi ◽  
A. Perdichizzi ◽  
M. Henze ◽  
J. Krueckels
Keyword(s):  
Thermal Performance ◽  
Thermal Protection ◽  
Cooling System ◽  
Incidence Angle ◽  
Leading Edge ◽  
Intensity Level ◽  
Inlet Flow ◽  
Flow Angle ◽  
Film Cooling Effectiveness ◽  
Nozzle Vane

Abstract In the present paper, the influence of inlet flow incidence on the thermal performance of a film cooled linear nozzle vane cascade is assessed. Tests have been carried out on a cooled cascade, featuring a showerhead cooling system made of 4 rows of cylindrical holes. The cascade was tested by varying the inlet flow angle in the range ±20° at a high inlet turbulence intensity level (Tu1 = 9%) and at a constant inlet Mach number of 0.12. The thermal characterization of vane leading edge region was obtained through adiabatic film cooling effectiveness measurements. Vane load distributions supported the discussion of the results. Varying the incidence angle in either positive or negative angles, the thermal protection on the vane is reduced while the maximum protection happened at 0° incidence case.

Comparison of RANS and DES Modeling Against Measurements of Leading Edge Film Cooling on a First-Stage Vane

2016 ◽  
Author(s):  
S. Ravelli ◽  
G. Barigozzi
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Leading Edge ◽  
Spanwise Direction ◽  
Intensity Level ◽  
Edge Region ◽  
Cooling Effectiveness ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Adiabatic Effectiveness

The performance of a showerhead arrangement of film cooling in the leading edge region of a first stage nozzle guide vane was experimentally and numerically evaluated. A six-vane linear cascade was tested at an isentropic exit Mach number of Ma2s = 0.42, with a high inlet turbulence intensity level of 9%. The showerhead cooling scheme consists of four staggered rows of cylindrical holes evenly distributed around the stagnation line, angled at 45° towards the tip. The blowing ratios tested are BR = 2.0, 3.0 and 4.0. Adiabatic film cooling effectiveness distributions on the vane surface around the leading edge region were measured by means of Thermochromic Liquid Crystals technique. Since the experimental contours of adiabatic effectiveness showed that there is no periodicity across the span, the CFD calculations were conducted by simulating the whole vane. Within the RANS framework, the very widely used Realizable k-ε (Rke) and the Shear Stress Transport k-ω (SST) turbulence models were chosen for simulating the effect of the BR on the surface distribution of adiabatic effectiveness. The turbulence model which provided the most accurate steady prediction, i.e. Rke, was selected for running Detached Eddy Simulation at the intermediate value of BR = 3. Fluctuations of the local temperature were computed by DES, due to the vortex structures within the shear layers between the main flow and the coolant jets. Moreover, mixing was enhanced both in the wall-normal and spanwise direction, compared to RANS modeling. DES roughly halved the prediction error of laterally averaged film cooling effectiveness on the suction side of the leading edge. However, neither DES nor RANS provided the expected decay of effectiveness progressing downstream along the pressure side, with 15% overestimation of ηav at s/C =0.2.

Aerodynamic and Heat Transfer Characterization of a Nozzle Vane Cascade With and Without Platform Cooling

2015 ◽  
Author(s):  
G. Barigozzi ◽  
A. Perdichizzi ◽  
M. Henze ◽  
J. Krueckels
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Cooling System ◽  
Leading Edge ◽  
Surface Flow ◽  
Secondary Flows ◽  
Intensity Level ◽  
Film Cooling Effectiveness ◽  
Nozzle Vane

In the present paper, aerodynamic and thermal performance of a linear nozzle vane cascade is fully assessed. Tests have been carried out with and without platform cooling, with coolant ejected through a slot located upstream of the leading edge. Cooling air is also ejected through a row of cylindrical holes located upstream of the slot, simulating a combustor cooling system. The cascade was tested at a high inlet turbulence intensity level (Tu1 = 9%) and at variable cooling injection conditions. Aero-thermal characterization of vane platform was obtained through 5-hole probe measurements, oil & dye surface flow visualizations, measurements of end wall adiabatic film cooling effectiveness and heat transfer coefficient. The platform cooling scheme operated at nominal injection rate was shown to effectively reduce the heat load over most of the platform surface, with only a small increase in secondary flows loss. Combustor holes injection resulted beneficial in controlling momentum of coolant approaching the cascade, thus limiting the secondary flows growth and resulting in an increase of the coolant film length inside of the passage.

Effect of Flow Parameter Variations on Full Coverage Film-Cooling Effectiveness for a Gas Turbine Blade

2007 ◽  
Author(s):  
Shantanu Mhetras ◽  
Je-Chin Han ◽  
Ron Rudolph
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Gas Turbines ◽  
Leading Edge ◽  
Suction Side ◽  
Intensity Level ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Mach Numbers ◽  
Film Cooling Holes

The effect of film cooling holes placed along the span of a fully-cooled high pressure turbine blade in a stationary, linear cascade on film cooling effectiveness is studied using the Pressure Sensitive Paint (PSP) technique. Effect of showerhead injection at the leading edge and the presence of compound angled, diffusing holes on the pressure and suction side are also examined. Six rows of compound angled shaped film cooling holes are provided on the pressure side while four such rows are provided on the suction side of the blade. The holes have a laidback and fan-shaped diffusing cross-section. Another three rows of cylindrical holes are drilled at a typical angle on the leading edge to capture the effect of showerhead film coolant injection. The film cooling hole arrangement simulates a typical film cooled blade design used in stage 1 rotor blades for gas turbines used for power generation. A typical blowing ratio is defined for each film hole row and tests are performed for 100%, 150% and 200% of this typical value. Tests are performed for inlet Mach numbers of 0.36 and 0.45 with corresponding exit Mach numbers of 0.51 and 0.68 respectively. The flow remains subsonic in the throat region for both Mach numbers. The corresponding free stream Reynolds number, based on the axial chord length and the exit velocity, are 1.3 million and 1.74 million respectively. Freestream turbulence intensity level at the cascade inlet is 6%. Results show that varying blowing ratios can have a significant impact on film-cooling effectiveness distribution. Large spanwise variations in effectiveness distributions are also observed. Similar distributions were observed for both Mach numbers.

scholarly journals Experimental Investigation of Disc Cavity Leakage Flow and Hub Endwall Contouring in a Linear Rotor Cascade

2011 ◽  
Author(s):  
Ryan D. Erickson ◽  
Terrence W. Simon ◽  
Luzeng Zhang ◽  
Hee-Koo Moon
Keyword(s):  
Thermal Performance ◽  
Film Cooling ◽  
Leading Edge ◽  
Turbine Rotor ◽  
Secondary Flows ◽  
Temperature Fields ◽  
Leakage Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Endwall Contouring

An experimental study is carried out in a stationary linear cascade which simulates a turbine rotor to compare the thermal performance of two new axisymmetric endwall contour geometries. Measurements of endwall adiabatic film cooling effectiveness and near-endwall passage temperature fields are made for this purpose. In addition to documenting endwall contouring effects, a range of disc cavity leakage flow rates is investigated. This information is meant to quantify, over the range tested, the benefits and penalties of introducing leakage flow into the passage using the designated endwall contouring. Special attention is paid to determine whether the endwall curvature has any effect on the interaction between mainstream and secondary flows within the passage. Results indicate improved thermal performance when strong endwall curvature exists near the blade leading edge. The strong curvature causes cavity leakage flow to remain closer to the endwall, thereby increasing cooling effectiveness.

Incidence Effect on the Aero-Thermal Performance of a Film Cooled Nozzle Vane Cascade

2018 ◽  
Author(s):  
H. Abdeh ◽  
G. Barigozzi ◽  
A. Perdichizzi ◽  
M. Henze ◽  
J. Krueckels
Keyword(s):  
Thermal Performance ◽  
Cooling System ◽  
Negative Impact ◽  
Surface Flow ◽  
Intensity Level ◽  
Inlet Flow ◽  
Flow Angle ◽  
Film Cooling Effectiveness ◽  
Nozzle Vane ◽  
End Wall

In the present paper, the influence of inlet flow incidence on the aerodynamic and thermal performance of a film cooled linear nozzle vane cascade is fully assessed. Tests have been carried out on a solid and a cooled cascade. In the cooled cascade, coolant is ejected at the end wall through a slot located upstream of the leading edge plane. Moreover, a vane showerhead cooling system is also realized through 4 rows of cylindrical holes. The cascade was tested at a high inlet turbulence intensity level (Tu1 = 9%) and at a constant inlet Mach number of 0.12 and nominal cooling condition, varying the inlet flow angle in the range ±20°. The aero-thermal characterization of vane platform was obtained through 5-hole probe and end wall adiabatic film cooling effectiveness measurements. Vane load distributions and surface flow visualizations supported the discussion of the results. A relevant negative impact of positive inlet flow incidence on the cooled cascade aerodynamic and thermal performance was detected. A negligible influence was instead observed at negative incidence, even at the lowest tested value of −20°.

Uncertainty Quantification of Aero-Thermal Performance of a Blade Endwall Considering Slot Geometry Deviation and Mainstream Fluctuation

2020 ◽  
Author(s):  
Zhi Tao ◽  
Zhendong Guo ◽  
Liming Song ◽  
Jun Li
Keyword(s):  
Sensitivity Analysis ◽  
Nusselt Number ◽  
Uncertainty Quantification ◽  
Thermal Performance ◽  
Film Cooling ◽  
Gas Turbines ◽  
Cooling Effectiveness ◽  
Inlet Flow ◽  
Flow Angle ◽  
Film Cooling Effectiveness

Abstract With the continuous increase of aerodynamic and thermal load, the endwall of modern gas turbines has become the critical region affected by the uncertainties in the manufacturing and operation process and thus is very likely to suffer performance degradation and thermal failure. Therefore, it is critical to understand and quantify the impacts of uncertainty factors on endwall aero-thermal performance. Based on Kriging surrogate, the frameworks of uncertainty quantification and global sensitivity analysis are constructed for a gas turbine blade endwall. The impacts of slot geometry deviations (slot width, endwall misalignment) and mainstream condition fluctuations (turbulence intensity, inlet flow angle) on endwall aero-thermal performance are quantified and analyzed. Results show that the actual performance of the endwall has a high probability of deviating from its nominal value. With respect to the nominal values, the maximum deviations of aerodynamic losses, averaged film cooling effectiveness and averaged Nusselt number reach up to 0.33%, 45% and 5.0%, respectively. The critical regions which are most sensitive to the input uncertainty parameters are identified. Furthermore, the inlet flow angle is proved to be the most significant parameter affecting the endwall aero-thermal performance through sensitivity analysis. The influence mechanisms of the inlet flow angle on endwall aero-thermal performance are clarified by detailed flow and thermal field analysis. Results show that the inlet flow angle significantly alters the size and strength of the secondary flow structures, resulting in a large variation of endwall aero-thermal performance. Quantitatively, a positive incidence angle of 2 degrees can lead to a 0.1% reduction of total pressure coefficient, a 12% reduction of averaged film cooling effectiveness and a 2% enhancement of averaged Nusselt number.

Effect of Flow Parameter Variations on Full Coverage Film-Cooling Effectiveness for a Gas Turbine Blade

2011 ◽  
Vol 134 (1) ◽  
Author(s):  
Shantanu Mhetras ◽  
Je-Chin Han ◽  
Ron Rudolph
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Gas Turbines ◽  
Leading Edge ◽  
Intensity Level ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Throat Region ◽  
Mach Numbers ◽  
Film Cooling Holes

The effect of film-cooling holes placed along the span of a fully cooled high pressure turbine blade in a stationary, linear cascade on film-cooling effectiveness is studied using the pressure sensitive paint technique. The effect of showerhead injection at the leading edge and the presence of compound angled, diffusing holes on the pressure and suction sides are also examined. Six rows of compound angled shaped film-cooling holes are provided on the pressure side while four such rows are provided on the suction side of the blade. The holes have a laidback and fan-shaped diffusing cross-section. Another three rows of cylindrical holes are drilled at a typical angle on the leading edge to capture the effect of showerhead film coolant injection. The film-cooling hole arrangement simulates a typical film cooled blade design used in Stage 1 rotor blades for gas turbines used for power generation. An optimal target blowing ratio is defined for each film hole row, and tests are performed for 100%, 150%, and 200% of this target value. Tests are performed for inlet Mach numbers of 0.36 and 0.45 with corresponding exit Mach numbers of 0.51 and 0.68, respectively. The flow remains subsonic in the throat region for both Mach numbers. The corresponding freestream Reynolds numbers, based on the axial chord length and the exit velocity, are 1.3×106 and 1.74×106, respectively. Freestream turbulence intensity level at the cascade inlet is 6%. The results show that varying blowing ratios can have a significant impact on film-cooling effectiveness distribution. Large spanwise variations in effectiveness distributions are also observed. Similar distributions were observed for both Mach numbers.

Film-Cooling Effectiveness From Shaped Film Cooling Holes for a Gas Turbine Blade

2008 ◽  
Author(s):  
Shantanu Mhetras ◽  
Je-Chin Han ◽  
Ron Rudolph
Keyword(s):  
Mach Number ◽  
Turbine Blade ◽  
Film Cooling ◽  
Gas Turbines ◽  
Leading Edge ◽  
Intensity Level ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Throat Region ◽  
Film Cooling Holes

The effect of film cooling holes placed along the span of a fully-cooled high pressure turbine blade in a stationary, linear cascade on film cooling effectiveness is studied using the Pressure Sensitive Paint (PSP) technique. Six rows of compound angled shaped film cooling holes are provided on the pressure side while four such rows are provided on the suction side of the blade. The holes have a laidback and fan-shaped diffusing cross-section. Another three rows of holes are drilled on the leading edge to capture the effect of showerhead film coolant injection. The film cooling hole arrangement simulates a typical film cooled blade design used in stage 1 rotor blades for gas turbines used for power generation. A minimum blowing ratio is defined for each film hole row and tests are performed for 1.0x, 1.33x, 1.67x, 2.0x and 2.67x of this minimum value. Tests are performed for an inlet Mach number of 0.36 with a corresponding exit Mach number of 0.51. The flow remains subsonic in the throat region. The corresponding free stream Reynolds number, based on the axial chord length and the exit velocity, is 1.3 million. Turbulence intensity level at the cascade inlet is 5% with an integral length scale of around 5cm. Results show that varying blowing ratios can have a significant impact on film-cooling effectiveness distribution. Large spanwise variations in effectiveness distributions are also observed. Results also show that the effectiveness magnitudes from superposition of effectiveness data from individual rows are comparable with that from full coverage film cooling.

Sign in / Sign up

Export Citation Format

Share Document