The Dynamic Behavior of Once-Through Direct Steam Generation Parabolic Trough Solar Collector Row Under Moving Shadow Conditions

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Su Guo ◽  
Yinghao Chu ◽  
Deyou Liu ◽  
Xingying Chen ◽  
Chang Xu ◽  
...  
Keyword(s):  
Mass Flow Rate ◽  
Dynamic Behavior ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Outlet Temperature ◽  
Steam Generation ◽  
Parabolic Trough ◽  
Direct Steam ◽  
Parabolic Trough Solar Collector

Compared with recirculation and injection modes, once-through direct steam generation (DSG) parabolic troughs are simpler to construct and require the lowest investment. However, the heat transfer fluid (HTF) in once-through DSG parabolic trough systems has the most complicated dynamic behavior, particularly during periods of moving shadows caused by small clouds and jet contrails. In this paper, a nonlinear distributed parameter dynamic model (NDPDM) is proposed to model the dynamic behavior of once-through DSG parabolic trough solar collector row under moving shadow conditions. Compared with state-of-the-art models, the proposed NDPDM possesses three characteristics: (a) adopting real-time local values of the heat transfer and friction resistance coefficients, (b) simulating the whole collector row, including the boiler and the superheated sections, and (c) modeling the disturbance of direct normal irradiance (DNI) level on DSG parabolic trough solar collector row under moving shadow conditions. Validated using experimental data, the NDPDM accurately predicts the dynamic characteristics of HTF during periods of partial and moving DNI disturbance. The fundamental and specific dynamic process of fluid parameters for a DSG parabolic trough solar collector row is provided in this paper. The results show the following: (a) Moving shadows have a significant impact on the outlet temperature and mass flow rate, and the impact lasts up to 1000 s even after the shadows completely leave the collector row. (b) The time for outlet steam temperature to reach a steady-state value for the first time is independent of the shadow width, speed, and moving direction. (c) High-frequency chattering of the outlet mass flow rate can be observed under moving DNI disturbance and will have a longer duration if the shadow width is larger or the shadow speed is slower. Compared with cases in which the whole system is shaded, partially shading cases have shown a longer duration of high-frequency chattering. (d) Both wider widths and slower speeds of shadow will cause a larger amplitude of responses in the outlet temperature and mass flow rate. When the shadow speed is low, there is a longer delay time of response in the mass flow rate of the outlet fluid. (e) The amplitude of response in the outlet temperature does not depend on the direction of clouds movement. However, if the DNI disturbance starts at the inlet of the collector row, there will be significant delay times in both outlet temperature and mass flow rate, and a larger amplitude of response in outlet mass flow rate.

Influence of Dimensionless Parameter on De-Ionized Water-alumina Nanofluid Based Parabolic Trough Solar Collector

2020 ◽  
Vol 13 (3) ◽  
pp. 206-221
Author(s):  
Vijayan Gopalsamy ◽  
Karunakaran Rajasekaran ◽  
Logesh Kamaraj ◽  
Siva Sivasaravanan ◽  
Metin Kok
Keyword(s):  
Heat Transfer ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Solar Collector ◽  
Dimensionless Parameter ◽  
Parabolic Trough ◽  
Alumina Nanofluid ◽  
Parabolic Trough Solar Collector

Background: Aqueous-alumina nanofluid was prepared using magnetic stirrer and ultrasonication process. Then, the prepared nanofluid was subjected to flow through the unshielded receiver of the parabolic trough solar collector to investigate the performance of the nanofluid and the effects of the dimensionless parameter were determined. Methods: The experimental work has been divided into two sections. First, the nanofluid was prepared and tested for its morphology, dimensions, and sedimentation using X-Ray Diffraction and Raman shift method. Then, the nanofluids of various concentrations from 0 to 4.0% are used as heat transfer fluid in unshielded type collector. Finally, the effect of the dimensionless parameter on the performance was determined. Results: For the whole test period, depending upon the bulk mean temperature, the dimensionless parameters such as Re and Nu varied from 1098 to 4552 & 19.30 to 46.40 for air and 2150 to 7551 & 11.11 to 48.54 for nanofluid. The enhancement of thermal efficiency found for 0% and 4.0% nanoparticle concentrations was 32.84% for the mass flow rate of 0.02 kg/s and 13.26% for the mass flow rate of 0.06 kg/s. Conclusion: Re and Nu of air depend on air velocity and ambient temperature. Re increased with the mass flow rate and decreased with concentration. Heat loss occurred by convection mode of heat transfer. Heat transfer coefficient and global efficiency increased with increased mass flow rate and volume fraction. The thermal efficiency of both 0% and 4.0% concentrations became equal for increased mass flow rate. It has been proven that at high mass flow rates, the time available to absorb the heat energy from the receiver is insufficient.

Exergy Optimization of a Novel Combination of a Liquid Air Energy Storage System and a Parabolic Trough Solar Collector Power Plant

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Shahram Derakhshan ◽  
Mohammadreza Khosravian
Keyword(s):  
Energy Storage ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Design Parameters ◽  
Parabolic Trough ◽  
Flow Rates ◽  
Mass Flow Rates ◽  
Parabolic Trough Solar Collector

In this paper, a parabolic trough solar collector (PTSC) plant is combined with a liquid air energy storage (LAES) system. The genetic algorithm (GA) is used to optimize the proposed system for different air storage mass flow rates. The roundtrip exergy ratio is considered as the objective function and pressures of six points and mass flow rates of five points are considered as design parameters. The effects of some environmental and key parameters such as different radiation intensities, ambient temperatures, output pressures of the second compressor, and mass flow rates of the collectors fluid on the exergy ratio are investigated. The results revealed that the system could produce 17526.15 kJ/s (17.5 MW) power in high demands time and 2233.48 kJ/s (2.2 MW) power in low demands time and the system shows that a value of 15.13% round trip exergy ratio is achievable. Furthermore, the exergy ratio decreased by 5.1% when the air storage mass flow rate increased from 10 to 15 kg/s. Furthermore, the exergy ratio decreases by increasing the collectors inside fluid mass flow rate or by decreasing radiation intensity.

Thermodynamic Analysis of an Integrated Solar-Based Cooling System in UAE

2014 ◽  
Author(s):  
Mohamed Gadalla ◽  
Amani Al Hammadi
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Irradiance ◽  
Solar Collector ◽  
Cooling System ◽  
Constant Mass ◽  
Parabolic Trough ◽  
Energy And Exergy ◽  
Parabolic Trough Solar Collector

Renewable energy resource is considered by many developed and developing countries as a promising and a cost effective candidate to provide energy. The operation of cooling systems in the United Arab Emirates (UAE) have some operating problems especially in summer such as severe grid dependent, excessive energy consumption, high emissions and high costs. So, more economically and environmentally friendly HVAC systems are desired to provide the required electricity demands for cooling loads while saving energy and having low emissions to the environment. In this paper, a parabolic trough solar collector is integrated with a triple effect absorption cooling system for sustainable development. A computer code is developed using Engineering Equation Solver (EES) software to obtain all required thermodynamic properties of water-lithium bromide (H2O/LiBr) solution and to optimize all operating parameters and carry out all detailed energy and exergy analyses for a 10 kW cooling capacity. In addition, the parabolic trough solar collector (PTSC) is also designed for the required cooling load and its overall dynamic behavior is also investigated. The solar irradiance available in the UAE on a monthly basis is used in the analysis of a PTSC-based HVAC cooling system. Energetic and exergetic efficiencies of the PTSC for every month are also evaluated under different operating conditions. The Overall monthly energy and exergy efficiencies of the integrated PTSC-based HVAC system for a constant mass flow rate of Therminol-66 and concentration ratio are calculated. The dynamic variation of the coefficient of performance of the integrated system with the solar irradiance and mass flow rate of the oil are also evaluated. Results show that both energetic and exergetic COPs are decreased with increasing the solar irradiance for a constant mass flow rate of oil and constant concentration ratio. It is found that increasing the mass flow rate of the oil from 0.1 to 0.5 kg/s results in decreasing the energetic COP from 2.15 to 1.98 and the exergetic COP from 2.05 to 1.93.

scholarly journals EXPERIMENTAL STUDY OF STEAM GENERATION BY PARABOLIC TROUGH CONCENTRATOR WITH TWO AXES TRACKING

2021 ◽  
Vol 25 (Special) ◽  
pp. 2-15-2-24
Author(s):  
Yasameen S. Raheema ◽  
◽  
Bashar O. Bedaiwi ◽  
Keyword(s):  
Experimental Study ◽  
Flow Rate ◽  
Thermal Performance ◽  
System Performance ◽  
Solar Collector ◽  
Solar Concentrator ◽  
Steam Generation ◽  
Parabolic Trough ◽  
Parabolic Trough Solar Collector ◽  
Practical Investigation

This paper describes an experimental model for estimating parabolic trough solar collector performance, as the Arduino micro-controller technology was applied to improve the optical and thermal efficiency of the system. The receiving tubes of different internal diameters (2mm, 6mm) were implemented to evaluate system performance. The practical investigation of the solar concentrator was conducted to generate steam at moderate temperatures, as the experiments were executed in Baghdad with geographical coordinates (33° 18' N, 44° 21' E) during specific days. The results showed the effectiveness of small diameters, as the significant enhancement of thermal performance was at a flow rate of 8 L/h and receiver tube diameters of 2 mm, as the improvement was 30% compared to 6 mm tubes.

Thermodynamic Performance Evaluation of a Solar Parabolic Dish Assisted Multigeneration System

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Muhammad Abid ◽  
Muhammad Sajid Khan ◽  
Tahir Abdul Hussain Ratlamwala
Keyword(s):  
Heat Transfer ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Integrated System ◽  
Heat Transfer Fluid ◽  
Outlet Temperature ◽  
Parabolic Dish ◽  
Single Effect

The concentration ratio of the parabolic dish solar collector (PDSC) is considered to be one of the highest among the concentrated solar power technologies (CSPs); therefore, such system is capable of generating more heat rate. The present paper focuses on the integration of the PDSC with the combined cycle (gas cycle as the toping cycle and steam cycle as the bottoming cycle) along with the utilization of waste heat from the power cycle to drive the single effect lithium bromide/water absorption cycle. Molten salt is used as a heat transfer fluid in the solar collector. The engineering equation solver (EES) is employed for the mathematical modeling and simulation of the solar integrated system. The various operating parameters (beam radiation, inlet and ambient temperatures of heat transfer fluid, mass flow rate of heat transfer fluid, evaporator temperature, and generator temperature) are varied to analyze their influence on the performance parameters (power output, overall energetic and exergetic efficiencies, outlet temperature of the receiver, and as coefficient of performance (COP) and exergy efficiencies) of the integrated system. The results show that the overall energy and exergy efficiencies are observed to be 39.9% and 42.95% at ambient temperature of 27 °C and solar irradiance of 1000 W/m2. The outlet temperature of the receiver is noticed to decrease from 1008 K to 528 K for an increase in the mass flow rate from 0.01 to 0.05 kg/s. The efficiency rate of the power plant is 38%, whereas COP of single effect absorption system is 0.84, and it will decrease from 0.87 to 0.79. However, the evaporator load is decreased to approximately 9.7% by increasing the generator temperature from 47 °C to 107 °C.

Solar Radiation Model Applied to a Low Temperature Evacuated Tubes Solar Collector

2018 ◽  
Vol 141 (3) ◽  
Author(s):  
Oscar A. López-Núñez ◽  
J. Arturo Alfaro-Ayala ◽  
J. J. Ramírez-Minguela ◽  
J. Nicolás Flores-Balderas ◽  
J. M. Belman-Flores
Keyword(s):  
Low Temperature ◽  
Solar Radiation ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Outlet Temperature ◽  
Radiation Model ◽  
Solar Radiation Model ◽  
Evacuated Tubes

A solar radiation model is applied to a low temperature water-in-glass evacuated tubes solar collector to predict its performance via computational fluid dynamics (CFD) numerical simulations. This approach allows obtaining the transmitted, reflected, and absorbed solar radiation flux and the solar heat flux on the surface of the evacuated tubes according to the geographical location, the date, and the hour of a day. Different environmental and operational conditions were used to obtain the outlet temperature of the solar collector; these results were validated against four experimental tests based on an Official Mexican Standard resulting in relative errors between 0.8% and 2.6%. Once the model is validated, two cases for the solar collector were studied: (i) different mass flow rates under a constant solar radiation and (ii) different solar radiation (due to the hour of the day) under a constant mass flow rate to predict its performance and efficiency. For the first case, it was found that the outlet temperature decreases as the mass flow rate increases reaching a steady value for a mass flow rate of 0.1 kg/s (6 l/min), while for the second case, the results showed a corresponding outlet temperature behavior to the solar radiation intensity reaching to a maximum temperature of 36.5 °C at 14:00 h. The CFD numerical study using a solar radiation model is more realistic than the previous reported works leading to overcome a gap in the knowledge of the low temperature evacuated tube solar collectors.

scholarly journals Mass flow rate optimization in solar heating systems based on a flat-plate solar collector: A case study

2021 ◽  
Vol 12 (3) ◽  
pp. 061-071
Author(s):  
Samer Yassin Alsadi ◽  
Tareq Foqha
Keyword(s):  
Flat Plate ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Optimization Problems ◽  
Heating System ◽  
Solar Heating ◽  
Outlet Temperature ◽  
Solar Systems

Little works considered the optimization of working fluids in solar systems. Engineers, designers and scientists are interested with the optimization problems, furthermore it is very important specially, for solar systems to improve the energetic behavior and increase their efficiencies as a conversion system of solar irradiance to a useful thermal power. According to the available literature, the criteria of optimization mainly relates to energetic and economic analysis (one of them or both). The analysis was based upon the maximum useful energy obtained from solar collector. Accordingly, the optimum mass flow rate was found aspires to infinity. The second analysis is based upon minimum cost of the unit of useful energy [$/W]. The optimum mass flow rate of solar air-heating flat-plate collector for the considered domestic solar heating system has been found 29 kg/h per square meters of solar collectors. This paper deals with a third criteria that is, the amount of the additional energy required to achieve the required task from the solar system by means of auxiliary heating system. In where both the outlet temperature and mass flow rate play crucial role in the heat exchange between the fluid in the collector loop and the fluid in the load loop.

Sign in / Sign up

Export Citation Format

Share Document