Simultaneous Schlieren–PLIF Studies for Ignition and Soot Luminosity Visualization With Close-Coupled High-Pressure Double Injections of n-Dodecane

2017 ◽  
Vol 139 (1) ◽  
Author(s):  
Ahmed Abdul Moiz ◽  
Khanh D. Cung ◽  
Seong-Young Lee
Keyword(s):  
Ignition Delay ◽  
Dwell Time ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Constant Density ◽  
Ambient Temperatures ◽  
Soot Precursors ◽  
Planar Laser ◽  
Main Injection ◽  
Fuel Injection Pressure

Studies are performed in a constant volume preburn type combustion vessel over a range of ambient temperatures (750 K, 800 K, and 900 K) at constant density (22.8 kg/m3) with 15% O2 by volume in the ambient at 1200 bar (n-dodecane) fuel injection pressure. The influence of the pilot (first) spray flame on the ignition and combustion characteristics of the main (second) injection is investigated while varying injection pressure, dwell time, and injection strategy. Simultaneous schlieren (with soot luminosity imaging) and 355 nm planar laser-induced fluorescence (PLIF) imaging for formaldehyde (CH2O) and polycyclic aromatic hydrocarbons (PAH) visualization was performed. At both 900 K and 800 K ambient, main injection exhibits a reduction in ignition delay (ID) by a factor of 2 over their respective pilots. For the ambient temperature condition of 750 K, reducing injection pressure from 1500 bar to 1200 bar causes a significant increase in ignition delay (by ∼0.8 ms), which was attributed to the influence of injection pressure on spray-mixing and early development of cool flame. Also, at 750 K ambient condition, multiple injection schedule having two 0.5 ms injections separated by a 0.5 ms dwell was found to have a shorter ignition delay than a single 0.5 ms injection. Studies carried at an 800 K ambient show that by increasing the dwell time, main interaction with pilot reactive intermediates can be controlled to avoid an early rich ignition of the main spray and to reduce soot precursors.

Optimization of operating parameters of an off-road automotive diesel engine running at highway drive conditions using Response Surface Methodology

2020 ◽  
pp. 1-48 ◽  
Author(s):  
Vinod Babu Marri ◽  
K. Madhu Murthy ◽  
G. Amba Prasad Rao
Keyword(s):  
Response Surface Methodology ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Operating Parameters ◽  
Injection Timing ◽  
Boost Pressure ◽  
Pilot Injection ◽  
Injection Quantity ◽  
Main Injection ◽  
Fuel Injection Pressure

Abstract The typical tradeoff between the two major emissions from compression ignition (CI) engines, smoke and oxides of nitrogen, is the unresolved challenge to the researchers. Techniques like engine downsizing, lowering intake oxygen concentration, multiple injections, use of retarded injection timings and higher injection pressures, etc. are widely employed for the alleviation of these harmful emissions. The influence of variation of fuel injection pressure (FIP), boost pressure, pilot injection timing (PIT), pilot injection quantity (PIQ) and main injection timing (MIT) are experimentally investigated in the present work. Mahindra mHawk four-cylinder diesel engine with provisions of a variable-geometry turbocharger (VGT), exhaust gas recirculation (EGR), and common-rail direct injection (CRDi) is chosen for the experimentation. Test runs are conducted at 1750 rpm and 80.3 N.m (4.6 bar bmep) corresponding to highway drive conditions, using 10 % EGR. Response surface methodology is employed for the design of experiments and to analyze the experimental data. Multi-objective response optimization is carried out to optimize engine-operating parameters that give desired performance and engine-out emissions. Confirmatory tests are conducted at design conditions to validate the results predicted by the model. This study reveals that the optimum performance and emission characteristics could be obtained using 120 kPa boost pressure; 61.1 MPa fuel injection pressure; 11.5 % pilot injection quantity with pilot injection at 332 °CA and main injection at 359 °CA.

Split Injection Strategies for Biodiesel-Fueled Premixed Charge Compression Ignition Combustion Engine—Part II: Particulate Studies

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Akhilendra Pratap Singh ◽  
Avinash Kumar Agarwal
Keyword(s):  
Fuel Injection ◽  
Combustion Engine ◽  
Chemical Characterization ◽  
Injection Pressure ◽  
Morphological Characterization ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Main Injection ◽  
Fuel Injection Pressure ◽  
Injection Strategies

Abstract In this study, experiments were performed in a single-cylinder research engine to investigate the particulate matter (PM) characteristics of the engine operated in premixed charge compression ignition (PCCI) mode combustion vis-a-vis baseline compression ignition (CI) mode combustion using three test fuels, namely, B20 (20% v/v biodiesel blended with mineral diesel), B40 (40% v/v/ biodiesel blended with mineral diesel), and baseline mineral diesel. The experiments were carried out at constant fuel injection pressure (FIP) (700 bar), constant engine speed (1500 rpm), and constant fuel energy input (0.7 kg/h diesel equivalent). PM characteristics of PCCI mode combustion were evaluated using two different fuel injection strategies, namely, single pilot injection (SPI) (35 deg before top dead center (bTDC)) and double pilot injection (DPI) (35 deg and 45 deg bTDC) at four different start of main injection (SoMI) timings. Results showed that both PCCI mode combustion strategies emitted significantly lower PM compared to baseline CI mode combustion strategy. However, the blending of biodiesel resulted in relatively higher PM emissions from both CI and PCCI combustion modes. Chemical characterization of PM showed that PCCI mode combustion emitted relatively lower trace metals compared to baseline CI mode combustion, which reduced further for B20. For detailed investigations of particulate structure, morphological characterization was done using transmission electron microscopy (TEM), which showed that PM emitted by B20-fueled PCCI mode combustion posed potentially lower health risk compared to baseline mineral diesel-fueled CI mode combustion.

Fuel Injection Strategy for Utilization of Mineral Diesel-Methanol Blend in a Common Rail Direct Injection Engine

2020 ◽  
Vol 142 (8) ◽  
Author(s):  
Akhilendra Pratap Singh ◽  
Nikhil Sharma ◽  
Vikram Kumar ◽  
Dev Prakash Satsangi ◽  
Avinash Kumar Agarwal
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Pilot Injection ◽  
Oxides Of Nitrogen ◽  
Gas Temperature ◽  
Injection Strategy ◽  
Main Injection ◽  
Pilot Fuel ◽  
Fuel Injection Pressure

Abstract Methanol fueled internal combustion (IC) engines have attracted significant attention due to their contributions in reducing environmental pollution and fossil fuel consumption. In this study, a single-cylinder research engine was operated on MD10 (10% (v/v) methanol blended with mineral diesel) and baseline mineral diesel to explore an optimized fuel injection strategy for efficient combustion and reduced emissions. The experiments were conducted at constant engine speed (1500 rpm) and load (3 kW) using two different fuel injection strategies, namely, single pilot injection (SPI) and double pilot injection (DPI) strategy. For each pilot fuel injection strategy, the start of main injection (SoMI) timing was varied from −3 to 6° crank angle (CA) before top dead center (bTDC). To examine the effect of fuel injection pressure (FIP), experiments were performed at three different FIPs (500, 750, and 1000 bars). Results showed that the MD10 fueled engine resulted in superior combustion compared with baseline mineral diesel, which was further improved by DPI at higher FIPs. The use of DPI strategy was found to be more effective at higher FIPs, resulting in higher brake thermal efficiency (BTE), lower exhaust gas temperature (EGT), and reduced oxides of nitrogen (NOx) emissions compared with SPI strategy. Detailed investigations showed that the addition of methanol in mineral diesel reduced particulates, especially the accumulation mode particles (AMP). Different statistical analysis and qualitative correlations between fuel injection parameters showed that higher FIP and advanced SoMI timings were suitable for particulate reduction from the MD10 fueled engine.

Experimental investigation of dwell time characteristics in high-pressure double-solenoid-valve fuel injection system

2019 ◽  
Vol 233 (13) ◽  
pp. 3281-3292
Author(s):  
Dan Xu ◽  
Qing Yang ◽  
Xiaodong An ◽  
Baigang Sun ◽  
Dongwei Wu ◽  
...  
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
Solenoid Valve ◽  
Injection System ◽  
Fuel Injection System ◽  
Pilot Injection ◽  
Main Injection ◽  
Injection Interval ◽  
The Difference ◽  
Variation Rule

The double-solenoid-valve fuel injection system consists of an electronic unit pump and an electronic injector. It can realize the separate control of fuel supply and injection and has the advantages of adjusting pressure by cycle and flexible controlling of the injection rate. The interval angle between the pilot and main injection directly affects the action degree and the characteristics of two adjacent injections, affecting engine performance. This work realizes multiple injection processes on the test platform of a high-pressure double-solenoid-valve fuel injection system, with maximum injection pressure reaching 200 MPa. In this study, the interval between driven current signal of pilot injection termination and that of main injection initiation is defined as the signal interval (DT1), whereas the interval between pilot injection termination and main injection initiation is defined as the injection interval (DT2). The differences between the signal and the injection intervals are calculated, and the variation rule of the difference with respect to the signal interval is analyzed. Results show that the variation rule of the difference with the signal interval first decreases, then increases, and finally decreases. The variation rule of the delay angle from the start of needle movement to the start of fuel injection is found to be the root cause of this rule. The influence of the injection pressure on needle deformation and fuel flow rate of the nozzle results in the variation rule. In addition, the influence of the cam speed, temperature, and pipe length on the difference between the signal and injection interval is determined. This research provides guidance for an optimal control strategy of the fuel injection process.

Sign in / Sign up

Export Citation Format

Share Document