Experimental Study of Effusion Cooling With Pressure-Sensitive Paint

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Guanghua Wang ◽  
Gustavo Ledezma ◽  
James DeLancey ◽  
Anquan Wang
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Cfd Simulation ◽  
Density Ratio ◽  
Open Loop ◽  
Pressure Sensitive Paint ◽  
Gas Temperature ◽  
Eddy Simulation ◽  
Pressure Sensitive ◽  
The Impact

Gas turbines overall efficiency enhancement requires further increasing of the firing temperature and decreasing of cooling flow usage. Multihole (or effusion, or full-coverage) film cooling is widely used for hot gas path components cooling in modern gas turbines. The present study focused on the adiabatic film effectiveness measurement of a round multihole flat-plate coupon. The measurements were conducted in a subsonic open-loop wind tunnel with a generic setup to cover different running conditions. The test conditions were characterized by a constant main flow Mach number of 0.1 with constant gas temperature. Adiabatic film effectiveness was measured by pressure-sensitive paint (PSP) through mass transfer analogy. CO2 was used as the coolant to reach the density ratio of 1.5. Rig computational fluid dynamics (CFD) simulation was conducted to evaluate the impact of inlet boundary layer on testing. Experimental data cover blowing ratios (BRs) at 0.4, 0.6, 0.8, 1.0, and 2.0. Both 2D maps and lateral average profiles clearly indicated that the film effectiveness increases with increasing BR for BR < 0.8 and decreases with increasing BR for BR > 0.8. This observation agreed with coolant jet behavior of single film row, i.e., attached, detached then reattached, and fully detached. PSP data quality was then discussed in detail for validating large eddy simulation.

Experimental and Numerical Investigations of Effusion Cooling for High Pressure Turbine Components: Part 1 — Experimental Study With PSP

2016 ◽  
Author(s):  
Guanghua Wang ◽  
Gustavo Ledezma ◽  
James DeLancey ◽  
Anquan Wang
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Cfd Simulation ◽  
Density Ratio ◽  
Open Loop ◽  
Gas Temperature ◽  
Cooling Flow ◽  
Eddy Simulation ◽  
Jet Behavior ◽  
Effectiveness Measurement

Gas turbines overall efficiency enhancement requires further increasing of the firing temperature and decreasing of cooling flow usage. Multi-Hole (or effusion, full coverage) film cooling is widely used for hot gas path components cooling in modern gas turbines. The present study focused on the adiabatic film effectiveness measurement of a round multi-hole flat plate coupon. The measurements were conducted in a subsonic open loop wind tunnel with a generic setup to cover different running conditions. The test conditions were characterized by a constant main flow Mach number of 0.1 with constant gas temperature. Adiabatic film effectiveness was measured by Pressure Sensitive Paint (PSP) through mass transfer analogy. CO2 was used as the coolant to reach the density ratio of 1.5. Rig CFD simulation was conducted to evaluate impact of inlet boundary layer on testing. Experimental data covers blowing ratios (BR) at 0.4, 0.6, 0.8, 1.0 and 2.0. Both 2D maps and lateral average profiles clearly indicated that film effectiveness increases with increasing BR for BR<0.8 and decreases with increasing BR for BR>0.8. This observation agreed with coolant jet behavior of single film row, i.e. attached, detached then reattached, and fully detached. PSP data quality was then discussed in detail for validating Large Eddy Simulation in Part 2.

Upstream Film Cooling on the Contoured Endwall of a Transonic Turbine Vane in an Annular Cascade

2020 ◽  
Author(s):  
Daniel A. Salinas ◽  
Izhar Ullah ◽  
Lesley M. Wright ◽  
Je-Chin Han ◽  
John W. McClintic ◽  
...  
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Lateral Spread ◽  
Pressure Sensitive Paint ◽  
Blow Down ◽  
Film Cooling Effectiveness ◽  
Pressure Sensitive ◽  
Mainstream Flow ◽  
Additional Protection ◽  
Annular Cascade

Abstract The effects of mainstream flow velocity, density ratio (DR), and coolant-to-mainstream mass flow ratio (MFR) were investigated on a vane endwall in a transonic, annular cascade. A blow down facility consisting of five vanes was used. The film cooling effectiveness was measured using binary pressure sensitive paint (BPSP). The mainstream flow was set using isentropic exit Mach numbers of 0.7 and 0.9. The coolant-to-mainstream density ratio varied from 1.0 to 2.0. The coolant to mainstream MFR varied from 0.75% to 1.25%. The endwall was cooled by eighteen discrete holes located upstream of the vane passage to provide cooling to the upstream half of the endwall. Due to the curvature of the vane endwall, the upstream holes provided uniform coverage entering the endwall passage. The coverage was effective leading to the throat of the passage, where the downstream holes could provide additional protection. Increasing the coolant flowrate increased the effectiveness provided by the film cooling holes. Increasing the density of the coolant increases the effectiveness on the endwall while enhancing the lateral spread of the coolant. Finally, increasing the velocity of the mainstream while holding the MFR constant also yields increased protection on the endwall. Over the range of flow conditions considered in this study, the binary pressure sensitive paint proved to be a valuable tool for obtaining detailed pressure and film effectiveness distributions.

Influence of Coolant Density on Turbine Blade Film Cooling at Transonic Cascade Flow Conditions Using the Pressure Sensitive Paint Technique

2021 ◽  
Author(s):  
Izhar Ullah ◽  
Sulaiman M. Alsaleem ◽  
Lesley M. Wright ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Pressure Side ◽  
Pressure Sensitive Paint ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Blade Tip ◽  
Film Cooling Holes

Abstract This work is an experimental study of film cooling effectiveness on a blade tip in a stationary, linear cascade. The cascade is mounted in a blowdown facility with controlled inlet and exit Mach numbers of 0.29 and 0.75, respectively. The free stream turbulence intensity is measured to be 13.5 % upstream of the blade’s leading edge. A flat tip design is studied, having a tip gap of 1.6%. The blade tip is designed to have 15 shaped film cooling holes along the near-tip pressure side (PS) surface. Fifteen vertical film cooling holes are placed on the tip near the pressure side. The cooling holes are divided into a 2-zone plenum to locally maintain the desired blowing ratios based on the external pressure field. Two coolant injection scenarios are considered by injecting coolant through the tip holes only and both tip and PS surface holes together. The blowing ratio (M) and density ratio (DR) effects are studied by testing at blowing ratios of 0.5, 1.0, and 1.5 and three density ratios of 1.0, 1.5, and 2.0. Three different foreign gases are used to create density ratio effect. Over-tip flow leakage is also studied by measuring the static pressure distributions on the blade tip using the pressure sensitive paint (PSP) measurement technique. In addition, detailed film cooling effectiveness is acquired to quantify the parametric effect of blowing ratio and density ratio on a plane tip design. Increasing the blowing ratio and density ratio resulted in increased film cooling effectiveness at all injection scenarios. Injecting coolant on the PS and the tip surface also resulted in reduced leakage over the tip. The conclusions from this study will provide the gas turbine designer with additional insight on controlling different parameters and strategically placing the holes during the design process.

scholarly journals Flat Plate and Turbine Vane Film-Cooling Performance with Laid-Back Fan-Shaped Holes

2019 ◽  
Vol 4 (2) ◽  
pp. 14 ◽  
Author(s):  
Tommaso Bacci ◽  
Alessio Picchi ◽  
Bruno Facchini
Keyword(s):  
Flat Plate ◽  
Film Cooling ◽  
Density Ratio ◽  
Pressure Sensitive Paint ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Turbine Vane ◽  
Experimental Works ◽  
Lift Off

Shaped holes are considered as an effective solution to enhance gas turbine film-cooling performance, as they allow to increase the coolant mass-flux, while limiting the detrimental lift-off phenomena. A great amount of work has been carried out in past years on basic flat plate configurations while a reduced number of experimental works deals with a quantitative assessment of the influence of curvature and vane pressure gradient. In the present work PSP (Pressure Sensitive Paint) technique is used to detail the adiabatic effectiveness generated by axial shaped holes with high value of Area Ratio close to 7, in three different configurations with the same 1:1 scale: first of all, a flat plate configuration is examined; after that, the film-cooled pressure and suction sides of a turbine vane model are investigated. Tests were performed varying the blowing ratio and imposing a density ratio of 2.5 . The experimental results are finally compared to the predictions of two different correlations, developed for flat plate configurations.

scholarly journals Experimental Investigation of Rotor Tip Film Cooling at an Axial Turbine with Swirling Inflow Using Pressure Sensitive Paint

2019 ◽  
Vol 4 (3) ◽  
pp. 23 ◽  
Author(s):  
Manuel Wilhelm ◽  
Heinz-Peter Schiffer
Keyword(s):  
Film Cooling ◽  
Large Scale ◽  
Density Ratio ◽  
Pressure Sensitive Paint ◽  
Axial Turbine ◽  
Film Cooling Effectiveness ◽  
Pressure Sensitive ◽  
Inlet Swirl ◽  
Blade Tip ◽  
Film Cooling Holes

Rotor tip film cooling is investigated at the Large Scale Turbine Rig, which is a 1.5-stage axial turbine rig operating at low speeds. Using pressure sensitive paint, the film cooling effectiveness η at a squealer-type blade tip with cylindrical pressure-side film cooling holes is obtained. The effect of turbine inlet swirl on η is examined in comparison to an axial inflow baseline case. Coolant-to-mainstream injection ratios are varied between 0.45% and 1.74% for an engine-realistic coolant-to-mainstream density ratio of 1.5. It is shown that inlet swirl causes a reduction in η for low injection ratios by up to 26%, with the trailing edge being especially susceptible to swirl. For injection ratios greater than 0.93%, however, η is increased by up to 11% for swirling inflow, while for axial inflow a further increase in coolant injection does not transfer into a gain in η .

Unsteady Wake and Coolant Density Effects on Turbine Blade Film Cooling Using Pressure Sensitive Paint Technique

2012 ◽  
Vol 134 (8) ◽  
Author(s):  
Akhilesh P. Rallabandi ◽  
Shiou-Jiuan Li ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Suction Side ◽  
Pressure Sensitive Paint ◽  
Suction Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Sensitive ◽  
Unsteady Wake ◽  
Film Cooling Holes

The effect of an unsteady stator wake (simulated by wake rods mounted on a spoke-wheel wake generator) on the modeled rotor blade is studied using the pressure sensitive paint (PSP) mass-transfer analogy method. Emphasis of the current study is on the midspan region of the blade. The flow is in the low Mach number (incompressible) regime. The suction (convex) side has simple angled cylindrical film-cooling holes; the pressure (concave) side has compound angled cylindrical film-cooling holes. The blade also has radial shower-head leading edge film-cooling holes. Strouhal numbers studied range from 0 to 0.36; the exit Reynolds number based on the axial chord is 530,000. Blowing ratios range from 0.5 to 2.0 on the suction side and 0.5 to 4.0 on the pressure side. Density ratios studied range from 1.0 to 2.5, to simulate actual engine conditions. The convex suction surface experiences film-cooling jet lift-off at higher blowing ratios, resulting in low effectiveness values. The film coolant is found to reattach downstream on the concave pressure surface, increasing effectiveness at higher blowing ratios. Results show deterioration in film-cooling effectiveness due to increased local turbulence caused by the unsteady wake, especially on the suction side. Results also show a monotonic increase in film-cooling effectiveness on increasing the coolant to mainstream density ratio.

Film Cooling Effectiveness From Two Rows of Compound Angled Cylindrical Holes Using Pressure-Sensitive Paint Technique

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Nian Wang ◽  
Mingjie Zhang ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han
Keyword(s):  
Flat Plate ◽  
Film Cooling ◽  
Density Ratio ◽  
Pressure Sensitive Paint ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Staggered Arrangement ◽  
Cylindrical Holes

This study investigates the effects of blowing ratio, density ratio, and spanwise pitch on the flat plate film cooling from two rows of compound angled cylindrical holes. Two arrangements of two-row compound angled cylindrical holes are tested: (a) the first row and the second row are oriented in staggered and same compound angled direction (β = +45 deg for the first row and +45 deg for the second row); (b) the first row and the second row are oriented in inline and opposite direction (β = +45 deg for the first row and −45 deg for the second row). The cooling hole is 4 mm in diameter with an inclined angle of 30 deg. The streamwise row-to-row spacing is fixed at 3d, and the spanwise hole-to-hole (p) is varying from 4d, 6d to 8d for both designs. The film cooling effectiveness measurements were performed in a low-speed wind tunnel in which the turbulence intensity is kept at 6%. There are 36 cases for each design including four blowing ratios (M = 0.5, 1.0, 1.5, and 2.0), three density ratios (DR = 1.0, 1.5, and 2.0), and three hole-to-hole spacing (p/d = 4, 6, and 8). The detailed film cooling effectiveness distributions were obtained by using the steady-state pressure-sensitive paint (PSP) technique. The spanwise-averaged cooling effectiveness are compared over the range of flow parameters. Some interesting observations are discovered including blowing ratio effect strongly depending on geometric design; staggered arrangement of the hole with same orientation does not yield better effectiveness at higher blowing ratio. Currently, film cooling effectiveness correlation of two-row compound angled cylindrical holes is not available, so this study developed the correlations for the inline arrangement of holes with opposing angles and the staggered arrangement of holes with same angles. The results and correlations are expected to provide useful information for the two-row flat plate film cooling analysis.

A Parametric Investigation of Vane Showerhead Film Cooling by Pressure-Sensitive Paint Technique

2020 ◽  
Vol 142 (3) ◽  
Author(s):  
H. Abdeh ◽  
G. Barigozzi ◽  
S. Ravelli ◽  
S. Rouina
Keyword(s):  
Turbulence Intensity ◽  
Film Cooling ◽  
Cooling System ◽  
Density Ratio ◽  
Leading Edge ◽  
Intensity Level ◽  
Pressure Sensitive Paint ◽  
Cooling Performance ◽  
Pressure Sensitive ◽  
Exit Mach Number

Abstract In this study, a parametric analysis of the thermal performance of a nozzle vane cascade with a showerhead cooling system made of four rows of cylindrical holes was carried out by using the pressure-sensitive paint (PSP) technique. Coolant-to-mainstream blowing ratio (BR), density ratio (DR), main flow isentropic exit Mach number (Ma2is), and turbulence intensity level (Tu1) were the considered parameters. The cascade was tested in an atmospheric wind tunnel at Ma2is values ranging from 0.2 to 0.6, with an inlet turbulence intensity level of 1.6% and 9%, at variable injection conditions of BR = 2.0, 3.0, 4.0. Moreover, the influence of the DR on the leading-edge film-cooling performance was investigated: the testing was carried out at DR = 1.0, using nitrogen as foreign gas, and DR = 1.5, with carbon dioxide serving as a coolant. In the near-hole region, higher BR and Ma2is resulted in higher effectiveness, while higher mainstream turbulence intensity reduced the thermal coverage in between the rows of holes, whatever the BR is. Further downstream along the vane pressure side, the effectiveness was negatively affected by rising the BR but positively influenced by lowering the mainstream turbulence intensity. Moreover, a decrease in the DR caused a reduction in the film-cooling performance, whose extent depends on the injection condition.

Influence of Hole Inlet Geometry on the Film Cooling Effectiveness From Shaped Film Cooling Holes

2019 ◽  
Author(s):  
Travis B. Watson ◽  
Kyle R. Vinton ◽  
Lesley M. Wright ◽  
Daniel C. Crites ◽  
Mark C. Morris ◽  
...  
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Lateral Spread ◽  
Pressure Sensitive Paint ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Sensitive ◽  
Inlet Geometry ◽  
Cooling Hole ◽  
Film Cooling Holes

Abstract The effect of film cooling hole inlet geometry is experimentally investigated in this study. Detailed film cooling effectiveness distributions are obtained on a flat plate using Pressure Sensitive Paint (PSP). The inlet of a traditional 12°-12°-12°, laidback, fanshaped hole varies from a traditional “round” opening to an oblong, racetrack shaped opening. In this study, a single racetrack inlet with an aspect ratio of 2:1 is compared to the round inlet. For both designs, the holes are inclined at θ = 30° relative to the mainstream. Blowing ratios of 0.5, 1.0, and 1.5 are considered as the coolant–to–mainstream density ratio varies between 1.0 and 4.0. For all cases, the freestream turbulence intensity is maintained at 7.5%. With the introduction of the racetrack shaped inlet, the coolant spreads laterally across the diffuse, laidback fanshaped outlet. The centerline film cooling effectiveness is reduced with the enhanced lateral spread of the coolant. However, the benefit of the shaped inlet is also observed with an increase in the area averaged film cooling effectiveness, compared to the traditional round inlet. Not only does the shaped inlet promote spreading of the coolant, it is also believed the racetrack shape suppresses turbulence within the hole allowing for enhanced film cooling protection near the film cooling holes.

Enhancement of Film Cooling Effectiveness Using Backward Injection Holes

2015 ◽  
Author(s):  
Sehjin Park ◽  
Eui Yeop Jung ◽  
Seon Ho Kim ◽  
Ho-Seong Sohn ◽  
Hyung Hee Cho
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Row Spacing ◽  
Pressure Sensitive Paint ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Cooling Method ◽  
Cylindrical Holes

Film cooling is a cooling method used to protect the hot components of a gas turbine from high temperature conditions. For this purpose, high and uniform film cooling effectiveness is required to protect the vanes/blades from excessive thermal stress. Backward injection is proposed as one of the methods for the improvement of film cooling effectiveness. In this study, experiments were performed to investigate the effect of backward injection on film cooling effectiveness, using pressure sensitive paint (PSP) method. Four experimental configurations were composed of forward and backward injection cylindrical holes. The cylindrical holes were aligned in two staggered rows with pitch (p) of 6d and row spacing (s) of 3d. The injection angles (α) of the cylindrical holes were 35° and 145° for forward and backward injection, respectively. The blowing ratios (M) ranged from 0.5 to 2.0 and the density ratio (DR) was about 1. The results indicate that backward injection enhanced not only film cooling effectiveness but also the lateral cooling uniformity. At a high blowing ratio, all configurations demonstrated higher film cooling effectiveness with backward injection than with only forward injection; thus, the dispersion of the backward injection jets enhanced the lateral coverage over wide areas. Configuration, in particular, arranged with forward injection in the first row and backward injection in the second row, obtained the highest film cooling effectiveness among the four cases studied, due to the dispersion of the backward injection jets and the coolant supply from the forward injection jets at a high blowing ratio.

Sign in / Sign up

Export Citation Format

Share Document