Finite Element Analysis of Flexible Pipes Under Axial Compression: Influence of the Sample Length

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Eduardo Ribeiro Malta ◽  
Clóvis de Arruda Martins
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Inner Core ◽  
High Sensitivity ◽  
Element Model ◽  
Sample Length ◽  
Flexible Pipe ◽  
Element Analysis ◽  
Flexible Pipes

In order to study the axial compressive behavior of flexible pipes, a nonlinear tridimensional finite element model was developed. This model recreates a five layer flexible pipe with two tensile armor layers, an external polymeric sheath, an orthotropic high strength tape, and a rigid inner core. Using this model, several studies were conducted to verify the influence of key parameters on the wire instability phenomenon. The pipe sample length can be considered as one of these parameters. This paper includes a detailed description of the finite element model itself and a case study where the length of the pipe is varied. The procedure of this analysis is here described and a case study is presented which shows that the sample length itself has no practical effect on the prebuckling response of the samples and a small effect on the limit force value. The postbuckling response, however, presented high sensitivity to the changes, but its erratic behavior has made impossible to establish a pattern.

Finite Element Analysis of Flexible Pipes Under Compression: Influence of the Sample Length

2015 ◽  
Author(s):  
Eduardo Ribeiro Malta ◽  
Clóvis de Arruda Martins
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
High Strength ◽  
Element Model ◽  
Sample Length ◽  
Flexible Pipe ◽  
Element Analysis ◽  
Flexible Pipes ◽  
The Stability

In order to study the compressive behavior of flexible pipes, a nonlinear tridimensional finite element model was developed. This model recreates a five layer flexible pipe with two tensile armor layers, an external polymeric sheath, an orthotropic high strength tape and a rigid inner nucleus. Using this model, several studies are being conducted to verify the influence of key parameters on the wire instability phenomenon. The pipe sample length can be considered one of these parameters and its variation causes significant change at the stability response of the tensile layers. This article includes a detailed description of the finite element model itself and a case study where the length of the pipe is changed. The procedure of this analysis is here described, along with the results.

Finite Element Analysis of Flexible Pipes Under Compression: Influence of the Friction Coefficient

2016 ◽  
Author(s):  
Eduardo Ribeiro Malta ◽  
Clóvis de Arruda Martins
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Finite Element Model ◽  
High Strength ◽  
Element Model ◽  
Flexible Pipe ◽  
Element Analysis ◽  
Frictional Contacts ◽  
Flexible Pipes ◽  
Nonlinear Finite Element Model

In order to study the compressive behavior of flexible pipes, a nonlinear Finite Element model was developed. This fully tridimensional model recreates a five layer flexible pipe with two tensile armor layers, an external polymeric sheath, an orthotropic high strength tape and a rigid inner nucleus. The friction coefficient is known as a key parameter in determining the instability response of flexible pipes tensile armor. Since the featured model includes all nonlinear frictional contacts between the layers, it has been used to conduct several experiments in order to investigate its influence on the response. This article includes a description of the Finite Element Model itself and a case study where the friction between the layers of the pipe is changed. The procedure of this analysis is here described, along with the results.

Finite Element Analysis of Flexible Pipes Under Compression: Influence of the Friction Coefficient

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Eduardo Ribeiro Malta ◽  
Clóvis de Arruda Martins
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Finite Element Model ◽  
High Strength ◽  
Element Model ◽  
Flexible Pipe ◽  
Element Analysis ◽  
Frictional Contacts ◽  
Flexible Pipes ◽  
Nonlinear Finite Element Model

In order to study the compressive behavior of flexible pipes, a nonlinear finite element model was developed. This fully tridimensional model recreates a five-layer flexible pipe with two tensile armor layers, an external polymeric sheath, an orthotropic high strength tape, and a rigid inner nucleus. The friction coefficient is known as a key parameter in determining the instability response of flexible pipes’ tensile armor. Since the featured model includes all nonlinear frictional contacts between the layers, it has been used to conduct several experiments in order to investigate its influence on the response. This article includes a description of the finite element model itself and a case study where the friction between the layers of the pipe is changed. The procedure of this analysis is described here, along with the results.

Finite Element Analysis of Flexible Pipes Under Compression

2014 ◽  
Author(s):  
Eduardo Ribeiro Malta ◽  
Clóvis de Arruda Martins
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Strength ◽  
Element Model ◽  
Large Displacements ◽  
Flexible Pipe ◽  
Element Analysis ◽  
Flexible Pipes ◽  
Compressive Loads ◽  
Surface Vessel

Axial compressive loads can appear in several situations during the service life of a flexible pipe, due to pressure variations during installation or due to surface vessel heave. The tensile armor withstands well tension loads, but under compression, instability may occur. A Finite Element model is constructed using Abaqus in order to study a flexible pipe compound by external sheath, two layers of tensile armor, a high strength tape and a rigid nucleus. This model is fully tridimensional and takes into account all kinds of nonlinearities involved in this phenomenon, including contacts, gaps, friction, plasticity and large displacements. It also has no symmetry or periodical limitations, thus permitting each individual wire of the tensile armor do displace in any direction. Case studies were performed and their results discussed.

Thermal Effects on the Anchoring of Flexible Pipe Tensile Armors

2015 ◽  
Author(s):  
Olaf O. Otte Filho ◽  
Rafael L. Tanaka ◽  
Rafael G. Morini ◽  
Rafael N. Torres ◽  
Thamise S. V. Vilela
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Thermal Effects ◽  
Current Model ◽  
Element Model ◽  
Small Scale ◽  
Flexible Pipe ◽  
System A ◽  
Flexible Pipes ◽  
Better Than

In the design of flexible pipes, predict the anchoring behavior on end fittings is always challenging. In this sense, Prysmian Surflex has developed a finite element model, which should help the end fitting design as well the prediction of the structural behavior and the acceptable maximum loads. The current model considers that the contact between armor-resin is purely cohesive and has been suitable for the design of end fittings [1] and [2]. But tests and new studies [3] and [4] indicate that only cohesive assumption would not be the best approach. Experimental data from prototype tests also show that the current model would not predict acceptable results for loads higher than those used in previous projects. This document will describe a study developed considering the friction and thermal contraction, instead of the cohesive phenomenon in the anchoring behavior analysis. Small scale tests were conducted in order to understand the anchoring relation between the resin and the wire used in the tensile armor. For this purpose, a special test device was developed to simulate an enclosure system. A parametric study was also performed to identify the cooling temperatures, coefficients of friction and contact properties parameters taken from small scale tests. The finite element model considers the thermal effects during exothermic curing. Using the new parameters obtained, a second model was developed. This model consists of only one real shaped bended wire inside an end fitting cavity. To validate the model, samples were tested on laboratory according anchoring design. The results of this round of tests were studied and corroborate the argument that use friction and thermal effects is better than use only the cohesive condition.

Helical Wire Behavior of Unbonded Flexible Pipes Under Bending

2015 ◽  
Author(s):  
Yutian Lu ◽  
Huibin Yan ◽  
Yong Bai ◽  
Peng Cheng
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Axial Strain ◽  
Bending Moment ◽  
Element Model ◽  
Flexible Pipe ◽  
Slip Mechanism ◽  
Flexible Pipes ◽  
Bending Behavior ◽  
Unbonded Flexible Pipes

The bending behavior of unbonded flexible pipe is governed by the response of the helical wires in the tensile armor to bending. The behavior of the helical wire, especially the axial strain, is influenced by the slip mechanism as a result of an increasing curvature under bending. In the present paper, two limit curves are considered with a certain curvature. A 3-D finite element model using ABAQUS is developed to simulate the practical behavior of the helical wires under bending. By comparing the FEA and theoretical results, a basic conclusion about the real slip path of the helical wire between two limit curves is introduced. A hysteretic bending moment-curvature relationship induced by the slip mechanism is obtained from the finite element model as well.

scholarly journals Numerical and Experimental Analysis of Umbilical Cables under Tension

2017 ◽  
Vol 26 (2) ◽  
pp. 096369351702600 ◽  
Author(s):  
Qingzhen Lu ◽  
Jinlong Chen ◽  
zhixun Yang ◽  
Yin Yuan chao ◽  
Qianjin Yue
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Inner Core ◽  
Theoretical Models ◽  
Element Model ◽  
Radial Deformation ◽  
Element Analysis ◽  
Umbilical Cable ◽  
The Finite Element Model

Umbilical cables are composite structures that consisting of metallic material and polymeric material. Analysing tension behaviour under axial loading is a key requirement to design the structure. A full three-dimensional finite element model is established in which the effect of radial deformation is given more attention. A plane finite element analysis is proposed to predict the radial stiffness of the inner core with several components. The tension behaviour of an umbilical cable is analysed by the proposed models. Tension tests of the umbilical cable were carried out. Compared with the available theoretical models in the literature, the finite element model has a satisfactory agreement with the experimental results. In addition, the finite element model is used for the assessment of the influence of the important parameters on the tension behaviour, which is helpful for the design of umbilical cable.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

scholarly journals Analysis for Wrinkling Behavior of Girth-Welded Line Pipe

1996 ◽  
Author(s):  
Luiz T. Souza ◽  
David W. Murray
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Internal Pressure ◽  
Experimental Test ◽  
Element Model ◽  
Element Analysis ◽  
Line Pipe ◽  
New Era ◽  
Analytical Tools

The paper presents results for finite element analysis of full-sized girth-welded specimens of line pipe and compares these results with the behavior exhibited by test specimens subjected to constant axial force, internal pressure and monotonically increasing curvatures. Recommendations for the ‘best’ type of analytical finite element model are given. Comparisons between the behavior predicted analytically and the observed behavior of the experimental test specimens are made. The mechanism of wrinkling is explained and the evolution of the deformed configurations for different wrinkling modes is examined. It is concluded that the analytical tools now available are sufficiently reliable to predict the behavior of pipe in a manner that was not previously possible and that this should create a new era for the design and assessment of pipelines if the technology is properly exploited by industry.

Sign in / Sign up

Export Citation Format

Share Document