Maximum Heat Transfer and Operating Temperature of Oscillating Heat Pipe

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Naoko Iwata ◽  
Hiroyuki Ogawa ◽  
Yoshiro Miyazaki
Keyword(s):  
Heat Transfer ◽  
Ambient Temperature ◽  
Heat Pipe ◽  
Critical Point ◽  
Heat Input ◽  
Operating Temperature ◽  
Working Fluid ◽  
Maximum Heat ◽  
Oscillating Heat Pipe ◽  
Maximum Heat Transfer

It is reported that the operating temperature of an oscillating heat pipe (OHP) at an operating limit is not dependent on the ambient temperature but that the maximum heat transfer is dependent on this. In this study, using different ambient temperature conditions, a 15-turn OHP filled with HFC-134a as a working fluid was operated until it dries out. The maximum heat transfer was found to vary with changes in the ambient temperature, but the operating temperature at an operating limit, which depends on the filling ratio (FR) of the working fluid, was found to be constant. At the operating limit, the operating temperature decreased with an increase in the FR when the ratio was greater than 50 wt.%. Visualization experiments and calculations were used to confirm that there is an increase in the liquid volume in the OHP in accordance with an increase in the heat input and that ultimately the OHP fills with the liquid, resulting in the failure of OHP operation. In contrast, at the operating limit, when the FR was less than 50%, the operating temperature increased in line with an increase in the FR. In this case, it is assumed that the volume of liquid slugs decreases as the heat input increases, thus causing the OHP to dry out. This theory is explained using a P–V diagram of the working fluid in the OHP. The OHP thermodynamic cycle reaches a saturated liquid or vapor line before it reaches a critical point if a specified volume is shifted from the specified volume at the critical point. The optimum FR for maximum heat transfer is therefore decided by the void ratio at the critical point of the working fluid.

Experimental and Numerical Simulation for Thermal Investigation of Oscillating Heat Pipe Using VOF Model

2020 ◽  
Vol 38 (1A) ◽  
pp. 88-104
Author(s):  
Anwar S. Barrak ◽  
Ahmed A. M. Saleh ◽  
Zainab H. Naji
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Heat Input ◽  
Cfd Simulation ◽  
Working Fluid ◽  
Maximum Deviation ◽  
Inlet Temperature ◽  
Maximum Heat ◽  
Oscillating Heat Pipe ◽  
Vof Model

This study is investigated the thermal performance of seven turns of the oscillating heat pipe (OHP) by an experimental investigation and CFD simulation. The OHP is designed and made from a copper tube with an inner diameter 3.5 mm and thickness 0.6 mm and the condenser, evaporator, and adiabatic lengths are 300, 300, and 210 mm respectively.  Water is used as a working fluid with a filling ratio of 50% of the total volume. The evaporator part is heated by hot air (35, 40, 45, and 50) oC with various face velocity (0.5, 1, and 1.5) m/s. The condenser section is cold by air at temperature 15 oC. The CFD simulation is done by using the volume of fluid (VOF) method to model two-phase flow by conjugating a user-defined function code (UDF) to the FLUENT code. Results showed that the maximum heat input is 107.75 W while the minimum heat is 13.75 W at air inlet temperature 35 oC with air velocity 0.5m/s. The thermal resistance decreased with increasing of heat input. The results were recorded minimum thermal resistance 0.2312 oC/W at 107.75 W and maximum thermal resistance 1.036 oC/W at 13.75W. In addition, the effective thermal conductivity increased due to increasing heat input.  The numerical results showed a good agreement with experimental results with a maximum deviation of 15%.

Experimental Investigation of Oscillating Heat Pipe With Hybrid Fluids of Liquid Metal and Water

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Tingting Hao ◽  
Hongbin Ma ◽  
Xuehu Ma
Keyword(s):  
Heat Transfer ◽  
Liquid Metal ◽  
Heat Pipe ◽  
Heat Input ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Experimental Results ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe

A new oscillating heat pipe (OHP) charged with hybrid fluids can improve thermal performance. The key difference in this OHP is that it uses room temperature liquid metal (Galinstan consisting of gallium, indium, and tin) and water as the working fluid. The OHP was fabricated on a copper plate with six turns and a 3 × 3 mm2 cross section. The OHP with hybrid fluids as the working fluid was investigated through visual observation and thermal measurement. Liquid metal was successfully driven to flow through the OHP by the pressure difference between the evaporator and the condenser without external force. Experimental results show that while added liquid metal can increase the heat transport capability, liquid metal oscillation amplitude decreases as the filling ratio of liquid metal increases. Visualization of experimental results show that liquid metal oscillation position and velocity increase as the heat input increases. Oscillating motion of liquid metal in the OHP significantly increases the heat transfer performance at high heat input. The lowest thermal resistance of 0.076 °C/W was achieved in the hybrid fluids-filled OHP with a heat input of 420 W. We experimentally demonstrated a 13% higher heat transfer performance using liquid metal as the working fluid compared to an OHP charged with pure water.

A Review on Nanofluid Heat Pipe

2014 ◽  
Author(s):  
Maryam Shafahi ◽  
Kevin Anderson ◽  
Ali Borna ◽  
Michael Lee ◽  
Alex Kim ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Exchangers ◽  
Working Fluid ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Medical Instruments ◽  
Thermo Physical Properties

This paper reviews the improvement in the heat pipe’s performance using nanofluid as the working fluid. The use of nanofluid enhances heat transfer in the heat pipe due to its improved thermo-physical properties, such as a higher thermal conductivity. Nanofluids proved to be the innovative approach to a variety of applications, such as electronics, medical instruments, and heat exchangers. The influence of different nanoparticles on heat pipe’s performance has been studied. Utilizing nanofluid as the working fluid leads to a significant reduction in heat pipe thermal resistance, an increase in maximum heat transfer, and an improvement of heat pipe thermal performance.

scholarly journals A heat pipe heat recovery heat exchanger for a mini-drier

2006 ◽  
Vol 17 (1) ◽  
pp. 50-57 ◽  
Author(s):  
A Meyer ◽  
R T R T Dobson
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Theoretical Model ◽  
Heat Pipe ◽  
Experimental Testing ◽  
Thermal Design ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Maximum Heat ◽  
Maximum Heat Transfer

This paper considers the thermal design and the experimental testing of a heat pipe (thermosyphon) heat exchanger for a relatively small commercially available mini-drier. The purpose of the heat exchanger is to recover heat from the moist waste air stream to preheat the fresh incoming air. The working fluid used was R134a and the correlations are given for the evaporator and condenser inside heat transfer coefficients as well as for the maximum heat transfer rate. The theoretical model and computer simulation program used for the thermal design calculations are described. The validity of the as-designed and manufactured heat exchanger coupled to the drier is experimentally verified. The theoretical model accurately predicted the thermal performance and a significant energy savings and a reasonable payback period was achieved.

scholarly journals Experimental investigations and optimization of process parameters of meshed-wick heat pipe

2020 ◽  
Vol 184 ◽  
pp. 01026 ◽  
Author(s):  
B.Ch Nookaraju ◽  
B. Hemanth Sai ◽  
K.V.N.S Himakar ◽  
N. Limba Reddy ◽  
N Sateesh
Keyword(s):  
Heat Transfer ◽  
Thermal Analysis ◽  
Heat Pipe ◽  
Heat Pipes ◽  
Working Fluid ◽  
Outer Diameter ◽  
Cylindrical Shape ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Screen Mesh

Heat pipes are used to transfer heat, which are hollow cylindrical shape device filled with small amount of working fluid, which can change its phase. The rate of heat transfer in heat pipes compared to normal heat exchanging devices is more. Depending on the applications of heat transfer various heat pipes are being designed. Methanol fluid is used with 50% fill ratio. It is made of copper with outer diameter of 15.88mm and inner diameter of 14.88mm. It consists of a screen mesh made of copper powder inside it with thickness of 0.5mm. Due to heat input methanol changes its phase from liquid to vapor. The vapor loses its heat and changes its phase back to liquid in the condenser. At the condenser section the vapour gives up it heat and changes its phase from vapour to liquid. The screen mesh assists the flow of condensed working fluid through capillary action. Optimized the results by “Taguchi method” using “Minitab software”. The Thermal analysis was done with the optimum conditions, which were obtained as a result from the optimization method by Ansys Fluent software. Then finally compared the thermal parameters obtained from experiments with the Thermal analysis result. It is found the maximum heat transfer rate is optimized using meshed wick heat pipe conditions.

Thermal Behavior Analysis of Wire Mini Heat Pipe

2011 ◽  
Vol 133 (12) ◽  
Author(s):  
Kleber Vieira de Paiva ◽  
Marcia Barbosa Henriques Mantelli ◽  
Leonardo Kessler Slongo
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Design Parameters ◽  
Working Fluid ◽  
Diffusion Welding ◽  
Flat Plates ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Heat Transfer Capacity ◽  
Microgravity Conditions

This work presents a theoretical and experimental analysis of a copper mini heat pipe (MHP), fabricated from a sandwich formed between cylindrical wires and flat plates, which are welded by means of diffusion process. The edges formed between the wires and the plates provide the working fluid capillary pressure necessary to overcome all the pressure losses. Two different experimental set ups were developed: one for test in gravity (laboratory) and other for microgravity conditions (International Space Station—ISS). The main difference between them lies in the condenser section. In the laboratory, cooling water was used to remove heat from the mini heat pipe, while at the ISS, fins and air fan were employed. In gravity, three different working fluids were tested: water, acetone, and methanol, while, for the experiments at the ISS, just water was used. A model was developed to predict the maximum heat transfer capacity of the device. In comparison to the literature models, the main difference of the present model is the variation of contact angle to adjust the mathematical model. Therefore, the main contributions of the present work are development of wire plate mini heat pipe fabrication methodology using diffusion welding, improvement of the analytical model used to predict the maximum heat transfer capacity of the device, determination of the present technology optimum design parameters, and test data obtained under microgravity conditions.

Experimental Investigation of a Flat-Plate Oscillating Heat Pipe With Groove-Enhanced Minichannels

2020 ◽  
Vol 12 (6) ◽  
Author(s):  
Matthew J. Rhodes ◽  
Scott M. Thompson
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Heat Pipe ◽  
Operating Temperature ◽  
Operating Conditions ◽  
Working Fluid ◽  
Oscillating Heat Pipe ◽  
Thin Film Evaporation ◽  
Film Evaporation ◽  
Wide Range

Abstract The thermal and capillary performance of a groove-enhanced, or “microchannel-embedded,” flat-plate oscillating heat pipe (MC FP-OHP) was experimentally investigated while varying heating width, orientation, working fluid and operating temperature. The copper MC FP-OHP possessed two layers of 1.02 × 1.02 mm2 square channels, with the center 14 channels possessing two embedded microchannels (0.25 × 0.13 mm2) aligned coaxially with the primary minichannels. A FP-OHP without embedded microchannels, but with deeper minichannels (DC FP-OHP), was also tested for comparison. The FP-OHPs were filled with Novec 7200 or water (both at 80% ± 2% by volume), and the heating widths were varied between full-width and localized configurations: 38.71 cm2 and 14.52 cm2, respectively. Experimental results demonstrate that the MC FP-OHP is significantly less sensitive to operating orientation and can perform with less detriment as heat flux increases. The MC FP-OHP has a lower startup heating requirement and provides more fluid wetting along the FP-OHP structure—which is advantageous for pumping liquid from the evaporator to the condenser. The MC FP-OHP has enhanced convective heat transfer during operation, as it was observed to have similar or lower thermal resistances to that of the DC FP-OHP for a wide range of operating conditions. The groove-enhanced minichannel within the MC FP-OHP also provides for enhanced heat transfer because there being more thin-film evaporation sites and vapor–liquid mixing between the minichannel and microchannels.

The Phenomenon of Unidirectional Circulating Flow in an Oscillating Heat Pipe

2019 ◽  
Author(s):  
Chunrong Yu ◽  
Yulong Ji ◽  
Lilin Chu ◽  
Zongyu Wang ◽  
Yadong Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Tilt Angle ◽  
Heat Input ◽  
Working Fluid ◽  
Oscillating Heat Pipe ◽  
Flow And Heat Transfer ◽  
The Difference ◽  
High Level ◽  
Relative High Level

Abstract The phenomena of two different types of unidirectional circulating flow pattern in a copper oscillating heat pipe (OHP) were firstly discovered and investigated. The OHP has six turns and three sections: evaporator, condenser and adiabatic sections with lengths of 40 mm, 64 mm, and 51 mm, respectively. R152a was used as the working fluid, the effects of the tilt angle from 0° to 90° and the heat input on the flow and heat transfer of the working fluid in OHP was studied. The experimental results showed that (1) the OHP charged with R152a can form a unidirectional circulating flow at any tilt angle under certain heat input, and the unidirectional circulating flow become steady as the heat input increases; (2) another type of circulating flow was found in the same OHP as the heat input increased to a relative high level, the difference between the two types of circulating flow is that the liquid slugs move forward with or without back forward oscillating movement; (3) the unidirectional circulating flow of the working fluid without back forward oscillating movement in the OHP significantly enhance the heat transfer of OHP.

Sign in / Sign up

Export Citation Format

Share Document