Estimation of Residual Stresses in Laminated Composites by Slitting Method Utilizing Eigen Strains

2016 ◽  
Vol 138 (4) ◽  
Author(s):  
M. M. Shokrieh ◽  
M. A. Kamangar
Keyword(s):  
Residual Stresses ◽  
Laminated Composites ◽  
Direct Calculation ◽  
High Sensitivity ◽  
Element Model ◽  
Accurate Method ◽  
Superposition Method ◽  
Slitting Method ◽  
Normalization Methods ◽  
Direct Use

The manufacturing parameters such as curing process cause residual stresses in polymeric laminated composites. Therefore, an accurate method of measurement of residual stresses is essential for the design and analysis of composites structures. The slitting method is recently used for measurement of the residual stresses in laminated composites. However, this method has some drawbacks such as high sensitivity to noise of measurements and high scattering in the final results, which necessitate using of normalization techniques. Moreover, the form of polynomials, used in the conventional slitting method for calculation of the stiffness matrix, has a significant effect on final results. In this paper, it is shown that the major reason of the drawbacks of the slitting method in calculating the residual stresses is a direct use of the elastic released strains recorded by strain gages. In the present study, instead of direct calculation of residual stresses from the elastic released strains, eigen strain distribution as a constant and invariant field has been calculated from the recorded elastic strains. Then, by using the calculated eigen strain field in a finite-element model, the residual stress filed was obtained. Also, instead of using polynomials to calculate the compliance, a superposition method was used. The results show that the new method decreases the sensitivity of the final results to noise and scattering of the experimental data. It means that the normalization methods are not needed any more.

scholarly journals Magnetoelastic Coupling and Delta-E Effect in Magnetoelectric Torsion Mode Resonators

Sensors ◽  
2021 ◽  
Vol 21 (6) ◽  
pp. 2022
Author(s):  
Benjamin Spetzler ◽  
Elizaveta V. Golubeva ◽  
Ron-Marco Friedrich ◽  
Sebastian Zabel ◽  
Christine Kirchhof ◽  
...  
Keyword(s):  
Low Frequency ◽  
High Sensitivity ◽  
Element Model ◽  
Mode Number ◽  
Frequency Change ◽  
General Description ◽  
Resonance Modes ◽  
Field Sensor ◽  
Magnetic Sensitivity ◽  
Bending Modes

Magnetoelectric resonators have been studied for the detection of small amplitude and low frequency magnetic fields via the delta-E effect, mainly in fundamental bending or bulk resonance modes. Here, we present an experimental and theoretical investigation of magnetoelectric thin-film cantilevers that can be operated in bending modes (BMs) and torsion modes (TMs) as a magnetic field sensor. A magnetoelastic macrospin model is combined with an electromechanical finite element model and a general description of the delta-E effect of all stiffness tensor components Cij is derived. Simulations confirm quantitatively that the delta-E effect of the C66 component has the promising potential of significantly increasing the magnetic sensitivity and the maximum normalized frequency change ∆fr. However, the electrical excitation of TMs remains challenging and is found to significantly diminish the gain in sensitivity. Experiments reveal the dependency of the sensitivity and ∆fr of TMs on the mode number, which differs fundamentally from BMs and is well explained by our model. Because the contribution of C11 to the TMs increases with the mode number, the first-order TM yields the highest magnetic sensitivity. Overall, general insights are gained for the design of high-sensitivity delta-E effect sensors, as well as for frequency tunable devices based on the delta-E effect.

Estimation of Residual Stress in Spiral Welded Pipe: Regression and Numerical Model

2012 ◽  
Author(s):  
Abul Fazal M. Arif ◽  
Ahmad S. Al-Omari ◽  
Anwar K. Sheikh ◽  
Yagoub Al-Nassar ◽  
M. Anis
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Critical Role ◽  
Large Diameter ◽  
Element Model ◽  
Regression Equation ◽  
Field Analysis ◽  
Welding Parameters ◽  
Splitting Test ◽  
Welded Pipe

Double submerged spiral-welded pipe (SWP) is used extensively throughout the world for large-diameter pipelines. Fabrication-induced residual stresses in spiral welded pipe have received increasing attention in gas, oil and petrochemical industry. Several studies reported in the literature verify the critical role of residual stresses in the failure of these pipes. Therefore, it is important that such stresses are accounted for in safety assessment procedures such as the British R6 and BS7910. This can be done only when detailed information on the residual stress distribution in the component is known. In industry, residual stresses in spiral welded pipe are measured experimentally by means of destructive techniques known as Ring Splitting Test. In this study, statistical analysis and linear-regression modeling were used to study the effect of several structural, material and welding parameters on ring splitting test opening for spiral welded pipes. The experimental results were employed to develop an appropriate regression equation, and to predict the residual stress on the spiral welded pipes. It was found that the developed regression equation explains 36.48% of the variability in the ring opening. In the second part, a 3-D finite element model is presented to perform coupled-field analysis of the welding of spiral pipe. Using this model, temperature as well as stress fields in the region of the weld edges is predicted.

scholarly journals Structural and Acoustic Responses of a Submerged Stiffened Conical Shell

2014 ◽  
Vol 2014 ◽  
pp. 1-14 ◽  
Author(s):  
Meixia Chen ◽  
Cong Zhang ◽  
Xiangfan Tao ◽  
Naiqi Deng
Keyword(s):  
Conical Shell ◽  
Element Model ◽  
Analytical Models ◽  
Superposition Method ◽  
Far Field ◽  
Fluid Loading ◽  
Low Frequencies ◽  
Structural Responses ◽  
The Individual ◽  
Field Sound

This paper studies the vibrational behavior and far-field sound radiation of a submerged stiffened conical shell at low frequencies. The solution for the dynamic response of the conical shell is presented in the form of a power series. A smeared approach is used to model the ring stiffeners. Fluid loading is taken into account by dividing the conical shell into narrow strips which are considered to be local cylindrical shells. The far-field sound pressure is solved by the Element Radiation Superposition Method. Excitations in two directions are considered to simulate the loading on the surface of the conical shell. These excitations are applied along the generator and normal to the surface of the conical shell. The contributions from the individual circumferential modes on the structural responses of the conical shell are studied. The effects of the external fluid loading and stiffeners are discussed. The results from the analytical models are validated by numerical results from a fully coupled finite element/boundary element model.

scholarly journals Numerical aspects for efficient welding computational mechanics

2014 ◽  
Vol 18 (suppl.1) ◽  
pp. 139-148
Author(s):  
Tarek Aburuga ◽  
Aleksandar Sedmak ◽  
Zoran Radakovic
Keyword(s):  
Residual Stresses ◽  
Three Dimensional ◽  
Shell Element ◽  
Element Model ◽  
Mechanical Analysis ◽  
Tensile Test Specimen ◽  
Integrity Assessment ◽  
Mass Scaling ◽  
Three Dimensional Models ◽  
Thermal Mechanical Analysis

The effect of the residual stresses and strains is one of the most important parameter in the structure integrity assessment. A finite element model is constructed in order to simulate the multi passes mismatched submerged arc welding SAW which used in the welded tensile test specimen. Sequentially coupled thermal mechanical analysis is done by using ABAQUS software for calculating the residual stresses and distortion due to welding. In this work, three main issues were studied in order to reduce the time consuming during welding simulation which is the major problem in the computational welding mechanics (CWM). The first issue is dimensionality of the problem. Both two- and three-dimensional models are constructed for the same analysis type, shell element for two dimension simulation shows good performance comparing with brick element. The conventional method to calculate residual stress is by using implicit scheme that because of the welding and cooling time is relatively high. In this work, the author shows that it could use the explicit scheme with the mass scaling technique, and time consuming during the analysis will be reduced very efficiently. By using this new technique, it will be possible to simulate relatively large three dimensional structures.

A Finite Element Model of Orthogonal Metal Cutting

1985 ◽  
Vol 107 (4) ◽  
pp. 349-354 ◽  
Author(s):  
J. S. Strenkowski ◽  
J. T. Carroll
Keyword(s):  
Finite Element ◽  
Plastic Strain ◽  
Residual Stresses ◽  
Finite Element Model ◽  
Metal Cutting ◽  
Element Model ◽  
Effective Plastic Strain ◽  
Orthogonal Metal Cutting ◽  
Chip Separation ◽  
Chip Geometry

A finite element model of orthogonal metal cutting is described. The paper introduces a new chip separation criterion based on the effective plastic strain in the workpiece. Several cutting parameters that are often neglected in simplified metal-cutting models are included, such as elastic-plastic material properties of both the workpiece and tool, friction along the tool rake face, and geometry of the cutting edge and workpiece. The model predicts chip geometry, residual stresses in the workpiece, and tool stresses and forces, without any reliance on empirical metal cutting data. The paper demonstrates that use of a chip separation criterion based on effective plastic strain is essential in predicting chip geometry and residual stresses with the finite element method.

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

2000 ◽  
Vol 123 (1) ◽  
pp. 150-154
Author(s):  
John H. Underwood ◽  
Michael J. Glennon
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Fatigue Life ◽  
Yield Strength ◽  
Residual Stresses ◽  
Solid Mechanics ◽  
Element Model ◽  
Pressure Vessels ◽  
Material Strength ◽  
Element Analysis

Laboratory fatigue life results are summarized from several test series of high-strength steel cannon breech closure assemblies pressurized by rapid application of hydraulic oil. The tests were performed to determine safe fatigue lives of high-pressure components at the breech end of the cannon and breech assembly. Careful reanalysis of the fatigue life tests provides data for stress and fatigue life models for breech components, over the following ranges of key parameters: 380–745 MPa cyclic internal pressure; 100–160 mm bore diameter cannon pressure vessels; 1040–1170 MPa yield strength A723 steel; no residual stress, shot peen residual stress, overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid mechanics analysis. Shot peen and overload residual stresses are modeled by superposing typical or calculated residual stress distributions on the applied stresses. Overload residual stresses are obtained directly from the finite element model of the breech, with the breech overload applied to the model in the same way as with actual components. Modeling of the fatigue life of the components is based on the fatigue intensity factor concept of Underwood and Parker, a fracture mechanics description of life that accounts for residual stresses, material yield strength and initial defect size. The fatigue life model describes six test conditions in a stress versus life plot with an R2 correlation of 0.94, and shows significantly lower correlation when known variations in yield strength, stress concentration factor, or residual stress are not included in the model input, thus demonstrating the model sensitivity to these variables.

Sign in / Sign up

Export Citation Format

Share Document