Axial Flutter Effects on the Axisymmetric Turbulent Boundary Layer Along Long Thin Circular Cylinders

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Stephen A. Jordan
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Skin Friction ◽  
Reynolds Numbers ◽  
Wall Pressure ◽  
Analytical Models ◽  
Circular Cylinders ◽  
Reynolds Stresses ◽  
Turbulent Statistics ◽  
Oscillatory Instabilities

Experimental observations of towed sonar arrays as characterized by long thin circular cylinders indicate transverse motions that are clearly identified by low-amplitudes, low-wavelengths, and low-frequencies. Although the cylinder length (L) to radius (a) is commonly large [L/a = O(103)] with high Reynolds numbers [O(104)], the corresponding length scale involving the average skin friction [CfL/a = O(10)] remains within the many experimental determinations of short to moderate length cylinders that experience oscillatory instabilities. Prior to the present investigation, any detrimental effects of these oscillatory instabilities on the thin cylinder flow physics that serve construction of the respective semi-empirical and semi-analytical models remained chiefly unknown. Herein, we began examining those turbulent statistics via fine-scale numerical simulations to critique the pragmatic adequacy of the representative design models. We were concerned in particular about the streamwise effects on the turbulent boundary layer (TBL), skin friction and wall pressure evolutions as well as the radial distributions of the leading normal and shear Reynolds stresses. Fortunately, no major deviations (within 10%) were discovered in the TBL statistics over a characteristic range of Reynolds numbers and TBL thicknesses as compared to the axisymmetric state. However, acute spikes (both subharmonics and harmonics) were detected in the wall pressure autospectra similar to that suspected in the towed cylinder experiments, which were conducted in large tow tanks and lake-type basins. These spikes are of paramount importance and should be explored further because they may lead to signal-to-noise ratios above acceptable limits.

scholarly journals Sonic Eddy Model of the Turbulent Boundary Layer

Fluids ◽  
2022 ◽  
Vol 7 (1) ◽  
pp. 37
Author(s):  
Paul Dintilhac ◽  
Robert Breidenthal
Keyword(s):  
Boundary Layer ◽  
Mach Number ◽  
Turbulent Boundary Layer ◽  
Skin Friction ◽  
Entrainment Rate ◽  
Square Root ◽  
Reynolds Stresses ◽  
Free Shear Layer ◽  
Velocity Fluctuations ◽  
Acoustic Signaling

The effects of Mach number on the skin friction and velocity fluctuations of the turbulent boundary layer are considered through a sonic eddy model. Originally proposed for free shear flows, the model assumes that the eddies responsible for momentum transfer have a rotation Mach number of unity, with the entrainment rate limited by acoustic signaling. Under this assumption, the model predicts that the skin friction coefficient should go as the inverse Mach number in a regime where the Mach number is larger than unity but smaller than the square root of the Reynolds number. The velocity fluctuations normalized by the friction velocity should be the inverse square root of the Mach number in the same regime. Turbulent transport is controlled by acoustic signaling. The density field adjusts itself such that the Reynolds stresses correspond to the momentum transport. In contrast, the conventional van Driest–Morkovin view is that the Mach number effects are due to density variations directly. A new experiment or simulation is proposed to test this model using different gases in an incompressible boundary layer, following the example of Brown and Roshko in the free shear layer.

A Model for High-Reynolds-Number Flow Past Rough-Walled Circular Cylinders

1977 ◽  
Vol 99 (3) ◽  
pp. 486-493 ◽  
Author(s):  
O. Gu¨ven ◽  
V. C. Patel ◽  
C. Farell
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Circular Cylinder ◽  
Turbulent Boundary Layer ◽  
Pressure Coefficient ◽  
Empirical Relation ◽  
Reynolds Numbers ◽  
Boundary Layer Separation ◽  
Circular Cylinders ◽  
Mean Flow

A simple analytical model for two-dimensional mean flow at very large Reynolds numbers around a circular cylinder with distributed roughness is presented and the results of the theory are compared with experiment. The theory uses the wake-source potential-flow model of Parkinson and Jandali together with an extension to the case of rough-walled circular cylinders of the Stratford-Townsend theory for turbulent boundary-layer separation. In addition, a semi-empirical relation between the base-pressure coefficient and the location of separation is used. Calculation of the boundary-layer development, needed as part of the theory, is accomplished using an integral method, taking into account the influence of surface roughness on the laminar boundary layer and transition as well as on the turbulent boundary layer. Good agreement with experiment is shown by the results of the theory. The significant effects of surface roughness on the mean-pressure distribution on a circular cylinder at large Reynolds numbers and the physical mechanisms giving rise to these effects are demonstrated by the model.

scholarly journals Evaluation of Skin Friction Drag Reduction in the Turbulent Boundary Layer Using Riblets

2019 ◽  
Vol 9 (23) ◽  
pp. 5199
Author(s):  
Hidemi Takahashi ◽  
Hidetoshi Iijima ◽  
Mitsuru Kurita ◽  
Seigo Koga
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Skin Friction ◽  
Three Dimensional ◽  
Hot Wire ◽  
Friction Drag ◽  
Freestream Velocity ◽  
Turbulent Statistics ◽  
Friction Drag Reduction ◽  
Riblet Surface

A unique approach to evaluate the reduction of skin friction drag by riblets was applied to boundary layer profiles measured in wind tunnel experiments. The proposed approach emphasized the turbulent scales based on hot-wire anemometry data obtained at a sampling frequency of 20 kHz in the turbulent boundary layer to evaluate the skin friction drag reduction. Three-dimensional riblet surfaces were fabricated using aviation paint and were applied to a flat-plate model surface. The turbulent statistics, such as the turbulent scales and intensities, in the boundary layer were identified based on the freestream velocity data obtained from the hot-wire anemometry. Those turbulent statistics obtained for the riblet surface were compared to those obtained for a smooth flat plate without riblets. Results indicated that the riblet surface increased the integral scales and decreased the turbulence intensity, which indicated that the turbulent structure became favorable for reducing skin friction drag. The proposed method showed that the current three-dimensional riblet surface reduced skin friction drag by about 2.8% at a chord length of 67% downstream of the model’s leading edge and at a freestream velocity of 41.7 m/s (Mach 0.12). This result is consistent with that obtained by the momentum integration method based on the pitot-rake measurement, which provided a reference dataset of the boundary layer profile.

The Effect of Biofilms on Turbulent Boundary Layers

1999 ◽  
Vol 121 (1) ◽  
pp. 44-51 ◽  
Author(s):  
M. P. Schultz ◽  
G. W. Swain
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Turbulent Boundary Layer ◽  
Skin Friction ◽  
Layer Structure ◽  
Reynolds Shear Stress ◽  
Skin Friction Coefficient ◽  
Laser Doppler Velocimeter ◽  
Reynolds Stresses ◽  
The Mean

Materials exposed in the marine environment, including those protected by antifouling paints, may rapidly become colonized by microfouling. This may affect frictional resistance and turbulent boundary layer structure. This study compares the mean and turbulent boundary layer velocity characteristics of surfaces covered with a marine biofilm with those of a smooth surface. Measurements were made in a nominally zero pressure gradient, boundary layer flow with a two-component laser Doppler velocimeter at momentum thickness Reynolds numbers of 5600 to 19,000 in a recirculating water tunnel. Profiles of the mean and turbulence velocity components, including the Reynolds shear stress, were measured. An average increase in the skin friction coefficient of 33 to 187 percent was measured on the fouled specimens. The skin friction coefficient was found to be dependent on both biofilm thickness and morphology. The biofilms tested showed varying effect on the Reynolds stresses when those quantities were normalized with the friction velocity.

LDA-Measurements of Transitional Flows Induced by a Square Rib

2001 ◽  
Vol 124 (1) ◽  
pp. 108-117 ◽  
Author(s):  
S. Becker ◽  
C. M. Stoots ◽  
K. G. Condie ◽  
F. Durst ◽  
D. M. McEligot
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Boundary Layers ◽  
Laser Doppler Anemometry ◽  
Plate Boundary ◽  
Index Of Refraction ◽  
Wall Region ◽  
Reynolds Stresses ◽  
Mean Velocity ◽  
Turbulent Statistics

New fundamental measurements are presented for the transition process in flat plate boundary layers downstream of two-dimensional square ribs. By use of laser Doppler anemometry (LDA) and a large Matched-Index-of-Refraction (MIR) flow system, data for wall-normal fluctuations and Reynolds stresses were obtained in the near wall region to y+<0.1 in addition to the usual mean streamwise velocity component and its fluctuation. By varying velocity and rib height, the experiment investigated the following range of conditions: k+=5.5 to 21, 0.3<k/δ1<1,180<Rek<740,6×104<Rex,k<1.5×105,ReΘ660,−125<x−xk/k<580. Consequently, results covered boundary layers which retained their laminar characteristics through those where a turbulent boundary layer was established shortly after reattachment beyond the forcing rib. For “large” elements, evolution of turbulent statistics of the viscous layer for a turbulent boundary layer y+<∼30 was rapid even in flows where the mean velocity profile still showed laminar behavior.

The effects of a favourable pressure gradient and of the Reynolds number on an incompressible axisymmetric turbulent boundary layer. Part 1. The turbulent boundary layer

1998 ◽  
Vol 359 ◽  
pp. 329-356 ◽  
Author(s):  
H. H. FERNHOLZ ◽  
D. WARNACK
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Shear Stress ◽  
Wall Shear Stress ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Skin Friction ◽  
Boundary Layers ◽  
Reynolds Stresses ◽  
The Mean

The effects of a favourable pressure gradient (K[les ]4×10−6) and of the Reynolds number (862[les ]Reδ2[les ]5800) on the mean and fluctuating quantities of four turbulent boundary layers were studied experimentally and are presented in this paper and a companion paper (Part 2). The measurements consist of extensive hot-wire and skin-friction data. The former comprise mean and fluctuating velocities, their correlations and spectra, the latter wall-shear stress measurements obtained by four different techniques which allow testing of calibrations in both laminar-like and turbulent flows for the first time. The measurements provide complete data sets, obtained in an axisymmetric test section, which can serve as test cases as specified by the 1981 Stanford conference.Two different types of accelerated boundary layers were investigated and are described: in this paper (Part 1) the fully turbulent, accelerated boundary layer (sometimes denoted laminarescent) with approximately local equilibrium between the production and dissipation of the turbulent energy and with relaxation to a zero pressure gradient flow (cases 1 and 3); and in Part 2 the strongly accelerated boundary layer with ‘inactive’ turbulence, laminar-like mean flow behaviour (relaminarized), and reversion to the turbulent state (cases 2 and 4). In all four cases the standard logarithmic law fails but there is no single parametric criterion which denotes the beginning or the end of this breakdown. However, it can be demonstrated that the departure of the mean-velocity profile is accompanied by characteristic changes of turbulent quantities, such as the maxima of the Reynolds stresses or the fluctuating value of the skin friction.The boundary layers described here are maintained in the laminarescent state just up to the beginning of relaminarization and then relaxed to the turbulent state in a zero pressure gradient. The relaxation of the turbulence structure occurs much faster than in an adverse pressure gradient. In the accelerating boundary layer absolute values of the Reynolds stresses remain more or less constant in the outer region of the boundary layer in accordance with the results of Blackwelder & Kovasznay (1972), and rise both in the vincinity of the wall in conjunction with the rising wall shear stress and in the centre region of the boundary layer with the increase of production.

On the Axisymmetric Turbulent Boundary Layer Growth Along Long Thin Circular Cylinders

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Stephen A. Jordan
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flat Plate ◽  
Shape Factor ◽  
Experimental Testing ◽  
Reynolds Numbers ◽  
Layer Growth ◽  
Factor H ◽  
Circular Cylinders ◽  
Length Scales

Even after several decades of experimental and numerical testing, our present-day knowledge of the axisymmetric turbulent boundary layer (TBL) along long thin circular cylinders still lacks a clear picture of many fundamental characteristics. The main issues causing this reside in the experimental testing complexities and the numerical simplifications. An important characteristic that is crucial for routine scaling is the boundary layer length scales, but the downstream growth of these scales (boundary layer, displacement, and momentum thicknesses) is largely unknown from the leading to trailing edges. Herein, we combine pertinent datasets with many complementary numerical computations (large-eddy simulations) to address this shortfall. We are particularly interested in expressing the length scales in terms of the radius-based and axial-based Reynolds numbers (Rea and Rex). Although the composite dataset gave an averaged shape factor H = 1.09 that is substantially lower than the planar value (H = 1.27), the shape factor distribution along the cylinder axis actually begins at the flat plate value then decays logarithmically to near unity. The integral length scales displayed power-law evolutions with variable exponents until high Rea (Rea > 35,000) where both scales then mimic streamwise consistency. Beneath this threshold, their streamwise growth is much slower than the flat plate (especially at low-Rea). The boundary layer thickness grew according to an empirical expression that is dependent on both Rea and Rex where its streamwise growth can far exceed the planar turbulent flow. These unique characteristics rank the thin cylinder axisymmetric TBL as a separate canonical flow, which was well documented by the previous investigations.

scholarly journals Analytical models of the wall-pressure spectrum under a turbulent boundary layer with adverse pressure gradient

2019 ◽  
Vol 877 ◽  
pp. 1007-1062 ◽  
Author(s):  
G. Grasso ◽  
P. Jaiswal ◽  
H. Wu ◽  
S. Moreau ◽  
M. Roger
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Pressure Fluctuations ◽  
Adverse Pressure Gradient ◽  
Wall Pressure ◽  
Analytical Models ◽  
Function Technique ◽  
Fast Evaluation ◽  
Wall Pressure Fluctuations

This paper presents a comprehensive analytical approach to the modelling of wall-pressure fluctuations under a turbulent boundary layer, unifying and expanding the analytical models that have been proposed over many decades. The Poisson equation governing pressure fluctuations is Fourier transformed in the wavenumber domain to obtain a modified Helmholtz equation, which is solved with a Green’s function technique. The source term of the differential equations is composed of turbulence–mean shear and turbulence–turbulence interaction terms, which are modelled separately within the hypothesis of a joint normal probability distribution of the turbulent field. The functional expression of the turbulence statistics is shown to be the most critical point for a correct representation of the wall-pressure spectrum. The effect of various assumptions on the shape of the longitudinal correlation function of turbulence is assessed in the first place with purely analytical considerations using an idealised flow model. Then, the effect of the hypothesis on the spectral distribution of boundary-layer turbulence on the resulting wall-pressure spectrum is compared with the results of direct numerical simulation computations and pressure measurements on a controlled-diffusion aerofoil. The boundary layer developing over the suction side of this aerofoil in test conditions is characterised by an adverse pressure gradient. The final part of the paper discusses the numerical aspect of wall-pressure spectrum computation. A Monte Carlo technique is used for a fast evaluation of the multi-dimensional integral formulation developed in the theoretical part.

scholarly journals Large-eddy simulation of separation and reattachment of a flat plate turbulent boundary layer

2015 ◽  
Vol 785 ◽  
pp. 78-108 ◽  
Author(s):  
W. Cheng ◽  
D. I. Pullin ◽  
R. Samtaney
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Flat Plate ◽  
Skin Friction ◽  
Separation Bubble ◽  
Reynolds Numbers ◽  
Wall Model ◽  
Large Eddy ◽  
Layer Flow

We present large-eddy simulations (LES) of separation and reattachment of a flat-plate turbulent boundary-layer flow. Instead of resolving the near wall region, we develop a two-dimensional virtual wall model which can calculate the time- and space-dependent skin-friction vector field at the wall, at the resolved scale. By combining the virtual-wall model with the stretched-vortex subgrid-scale (SGS) model, we construct a self-consistent framework for the LES of separating and reattaching turbulent wall-bounded flows at large Reynolds numbers. The present LES methodology is applied to two different experimental flows designed to produce separation/reattachment of a flat-plate turbulent boundary layer at medium Reynolds number $Re_{{\it\theta}}$ based on the momentum boundary-layer thickness ${\it\theta}$. Comparison with data from the first case at $Re_{{\it\theta}}=2000$ demonstrates the present capability for accurate calculation of the variation, with the streamwise co-ordinate up to separation, of the skin friction coefficient, $Re_{{\it\theta}}$, the boundary-layer shape factor and a non-dimensional pressure-gradient parameter. Additionally the main large-scale features of the separation bubble, including the mean streamwise velocity profiles, show good agreement with experiment. At the larger $Re_{{\it\theta}}=11\,000$ of the second case, the LES provides good postdiction of the measured skin-friction variation along the whole streamwise extent of the experiment, consisting of a very strong adverse pressure gradient leading to separation within the separation bubble itself, and in the recovering or reattachment region of strongly-favourable pressure gradient. Overall, the present two-dimensional wall model used in LES appears to be capable of capturing the quantitative features of a separation-reattachment turbulent boundary-layer flow at low to moderately large Reynolds numbers.

Sign in / Sign up

Export Citation Format

Share Document