Postinjection Strategy for the Reduction of the Peak Pressure Rise Rate of Neat n-Butanol Combustion

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Marko Jeftić ◽  
Ming Zheng
Keyword(s):  
Nitrogen Oxide ◽  
Thermal Efficiency ◽  
Peak Pressure ◽  
Pressure Rise ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Load Conditions

Enhanced premixed combustion of neat butanol in a compression ignition engine can have challenges with regards to the peak pressure rise rate (PRR) and the peak in-cylinder pressure. It was proposed to utilize a butanol postinjection to reduce the peak PRR and the peak in-cylinder pressure while maintaining a constant engine load. Postinjection timing and duration sweeps were carried out with neat n-butanol in a compression ignition engine. The postinjection timing sweep results indicated that the use of an early butanol postinjection reduced the peak PRR and the peak in-cylinder pressure and it was observed that there was an optimal postinjection timing range for the maximum reduction of these parameters. The results also showed that an early postinjection of butanol increased the nitrogen oxide emissions, and a Fourier transform infrared spectroscopy (FTIR) analysis revealed that late postinjections increased the emissions of unburned butanol. The postinjection duration sweep indicated that the peak PRR was significantly reduced by increasing the postinjection duration at constant load conditions. There was also a reduction in the peak in-cylinder pressure. Measurements with a hydrogen mass spectrometer showed that there was an increased presence of hydrogen in the exhaust gas when the postinjection duration was increased but the total yield of hydrogen was relatively low. It was observed that the coefficient of variation for the indicated mean effective pressure was significantly increased and that the indicated thermal efficiency was reduced when the postinjection duration was increased. The results also showed that there were increased nitrogen oxide, carbon monoxide, and total hydrocarbon (THC) emissions for larger postinjections. Although the use of a postinjection resulted in emission and thermal efficiency penalties at medium load conditions, the results demonstrated that the postinjection strategy successfully reduced the peak PRR, and this characteristic can be potentially useful for higher load applications where the peak PRR is of greater concern.

Post Injection Strategy for the Reduction of the Peak Pressure Rise Rate of Neat N-Butanol Combustion

2015 ◽  
Author(s):  
Marko Jeftić ◽  
Ming Zheng
Keyword(s):  
Peak Pressure ◽  
Pressure Rise ◽  
Injection Timing ◽  
Post Injection ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Pressure Rise Rate ◽  
Injection Duration ◽  
Rise Rate

Enhanced premixed combustion of neat butanol in a compression ignition engine can have challenges with regards to the peak pressure rise rate and the peak in-cylinder pressure. It was proposed to utilize a butanol post injection to reduce the peak pressure rise rate and the peak in-cylinder pressure while maintaining a constant engine load. Post injection timing and duration sweeps were carried out with neat n-butanol in a compression ignition engine. The post injection timing sweep results indicated that the use of an early butanol post injection reduced the peak pressure rise rate and the peak in-cylinder pressure and it was observed that there was an optimal post injection timing range for the maximum reduction of these parameters. The results also showed that an early post injection of butanol increased the nitrogen oxide emissions and an FTIR analysis revealed that late post injections increased the emissions of unburned butanol. The post injection duration sweep indicated that the peak pressure rise rate was significantly reduced by increasing the post injection duration at constant load conditions. There was also a reduction in the peak in-cylinder pressure. Measurements with a hydrogen mass spectrometer showed that there was an increased presence of hydrogen in the exhaust gas when the post injection duration was increased but the total yield of hydrogen was relatively low. It was observed that the coefficient of variation for the indicated mean effective pressure was significantly increased and that the indicated thermal efficiency was reduced when the post injection duration was increased. The results also showed that there were increased nitrogen oxide, carbon monoxide, and total hydrocarbon emissions for larger post injections. Although the use of a post injection resulted in emission and thermal efficiency penalties at medium load conditions, the results demonstrated that the post injection strategy successfully reduced the peak pressure rise rate and this characteristic can be potentially useful for higher load applications where the peak pressure rise rate is of greater concern.

Combustion parameter evaluation of diesel engine via vibration acceleration signal

2021 ◽  
pp. 146808742110308
Author(s):  
Pan Zhang ◽  
Wenzhi Gao ◽  
Yong Li ◽  
Zhaoyi Wei
Keyword(s):  
Peak Pressure ◽  
Pressure Rise ◽  
Peak Position ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Combustion Control ◽  
Pressure Rise Rate ◽  
Acceleration Signal ◽  
Rise Rate ◽  
Start Of Combustion

Efficient combustion control has increasingly become a quality requirement for automobile manufacturers because of its impact on pollutant and greenhouse gas emissions. In view of this, the management system development of modern internal combustion engines is mainly aimed at combustion control. The real-time detection of in-cylinder pressure characteristic parameters has a considerable significance on the closed-loop combustion control of the internal combustion engine. This paper presents a detection method in which the start of combustion, peak pressure, maximum pressure rise rate, and phase of maximum pressure rise rate are identified through vibration acceleration signal. In order to analyze the relationship between vibration and in-cylinder pressure signal, experimental data are acquired in a diesel engine by implementing various injection strategies and engine operating conditions (speed and load). The results show that the start of combustion can be detected by analyzing its relationship with the peak position of the filtered vibration signal, and the phase of the maximum pressure rise rate can be identified by examining its relationship with the zero-cross position that is adjacent to the right of the peak position. Moreover, the filtered vibration signals are also truncated in the same length and utilized as inputs for algorithms to detect the peak pressure and the maximum pressure rise rate. The algorithms are mainly performed on data compression (or feature extraction) and target regression. Major algorithms, such as one-dimensional convolutional neural network, compression sensing, wavelet decomposition, multilayer perceptron, and support vector machine, are tested. Various experimental results verify that for the test engine the phase detection accuracy of the start of combustion and maximum pressure rise rate is less than 1.7°CA for a 95% prediction interval width. For the detection of the peak pressure and maximum pressure rise rate, the normalized error threshold is set as 0.05, then the accuracies can be not less than 95%.

Drive Cycle Efficiency and Emissions Estimates for Reactivity Controlled Compression Ignition in a Multi-Cylinder Light-Duty Diesel Engine

2011 ◽  
Author(s):  
Scott J. Curran ◽  
Kukwon Cho ◽  
Thomas E. Briggs ◽  
Robert M. Wagner
Keyword(s):  
Diesel Engine ◽  
Pressure Rise ◽  
Injection System ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Drive Cycle ◽  
Reactivity Controlled Compression Ignition ◽  
Pressure Rise Rate ◽  
Light Duty ◽  
Rise Rate

In-cylinder blending of gasoline and diesel to achieve Reactivity Controlled Compression Ignition (RCCI) has been shown to reduce NOx and PM emissions while maintaining or improving brake thermal efficiency (BTE) as compared to conventional diesel combustion (CDC). The RCCI concept has an advantage over many advanced combustion strategies in that by varying both the percent of premixed gasoline and EGR rate, stable combustion can be extended over more of the light-duty drive cycle load range. Changing the percent of premixed gasoline changes the fuel reactivity stratification in the cylinder providing further control of combustion phasing and cylinder pressure rise rate than the use of EGR alone. This paper examines the combustion and emissions performance of light-duty diesel engine using direct injected diesel fuel and port injected gasoline to enable RCCI for steady-state engine conditions which are consistent with a light-duty drive cycle. A GM 1.9L four-cylinder engine with the stock compression ratio of 17.5:1, common rail diesel injection system, high-pressure EGR system and variable geometry turbocharger was modified to allow for port fuel injection with gasoline. Engine-out emissions, engine performance and combustion behavior for RCCI operation is compared against both CDC and a premixed charge compression ignition (PCCI) strategy which relies on high levels of EGR dilution. The effect of percent of premixed gasoline, EGR rate, boost level, intake mixture temperature, combustion phasing, and cylinder pressure rise rate is investigated for RCCI combustion for the light-duty modal points. Engine-out emissions of NOx and PM were found to be considerably lower for RCCI operation as compared to CDC and PCCI, while HC and CO emissions were higher. BTE was similar or higher for many of the modal conditions for RCCI operation. The emissions results are used to estimate hot-start FTP-75 emissions levels with RCCI and are compared against CDC and PCCI modes.

Combustion Noise Investigation With Multi-Cylinder RCCI

2013 ◽  
Author(s):  
Scott J. Curran ◽  
James P. Szybist ◽  
Robert M. Wagner
Keyword(s):  
Pressure Rise ◽  
Combustion Noise ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Engine Operation ◽  
Reactivity Controlled Compression Ignition ◽  
Pressure Rise Rate ◽  
Advanced Combustion ◽  
Rise Rate ◽  
Noise Metrics

Advanced combustion techniques have shown promise for achieving high thermal efficiency with simultaneous reductions in oxides of nitrogen (NOx) and particulate matter (PM) emissions. Many advanced combustion studies have used some form of noise-related metric to constrain engine operation, whether it be cylinder pressure rise rate, combustion noise, or ringing intensity. As the development of advanced combustion techniques progresses towards production-viable concepts, combustion noise is anticipated to be of the upmost concern for consumer acceptability. This study compares the noise metrics of cylinder pressure rise rate with combustion noise as measured by an AVL combustion noise meter over a wide range of engine operation conditions with reactivity controlled compression ignition on a light-duty multi-cylinder diesel engine modified to allow for direct injection of diesel fuel and port fuel injection of gasoline. Key parameters affecting noise metrics are engine load, speed, and the amount of boost. The trade-offs between high efficiency, low NOX emissions, and combustion noise were also explored. Additionally, the combustion noise algorithm integrated into the Drivven combustion analysis toolkit is compared to cylinder pressure rise rate and combustion noise as measured with a combustion noise meter. It is shown that the combustion noise of the multi-cylinder reactivity controlled compression ignition map can approach 100 dB while keeping the maximum pressure rise under 100 kPa/CAD.

scholarly journals Effect of Ambient Temperature and Humidity on Combustion and Emissions of a Spark-Assisted Compression Ignition Engine

2016 ◽  
Vol 139 (5) ◽  
Author(s):  
Yan Chang ◽  
Brandon Mendrea ◽  
Jeff Sterniak ◽  
Stanislav V. Bohac
Keyword(s):  
Ambient Temperature ◽  
Pressure Rise ◽  
Ambient Air ◽  
Maximum Pressure ◽  
Successful Implementation ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Temperature And Humidity

Spark-assisted compression ignition (SACI) offers more practical combustion phasing control and a lower pressure rise rate than homogeneous charge compression ignition (HCCI) combustion and improved thermal efficiency and lower NOx emissions than spark ignition (SI) combustion. Any practical passenger car engine, including one that uses SACI in part of its operating range, must be robust to changes in ambient conditions. This study investigates the effects of ambient temperature and humidity on stoichiometric SACI combustion and emissions. It is shown that at the medium speed and load SACI test point selected for this study, increasing ambient air temperature from 20 °C to 41 °C advances combustion phasing, increases maximum pressure rise rate, causes a larger fraction of the charge to be consumed by auto-ignition (and a smaller fraction by flame propagation), and increases NOx. Increasing ambient humidity from 32% to 60% retards combustion phasing, reduces maximum pressure rise rate, increases coefficient of variation (COV) of indicated mean effective pressure (IMEP), reduces NOx, and increases brake-specific fuel consumption (BSFC). These results show that successful implementation of SACI combustion in real-world driving requires a control strategy that compensates for changes in ambient temperature and humidity.

Initial Results on a New Light-Duty 2.7L Opposed-Piston Gasoline Compression Ignition Multi-Cylinder Engine

2018 ◽  
Author(s):  
Ashwin Salvi ◽  
Reed Hanson ◽  
Rodrigo Zermeno ◽  
Gerhard Regner ◽  
Mark Sellnau ◽  
...  
Keyword(s):  
Pressure Rise ◽  
High Load ◽  
Combustion Stability ◽  
Residual Fraction ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Peak Cylinder Pressure ◽  
Low Load ◽  
Initial Results ◽  
Load Conditions

Gasoline compression ignition (GCI) is a cost-effective approach to achieving diesel-like efficiencies with low emissions. Traditional challenges with GCI arise at low-load conditions due to low charge temperatures causing combustion instability and at high-load conditions due to peak cylinder pressure and noise limitations. The fundamental architecture of the two-stroke Achates Power Opposed-Piston Engine (OP Engine) enables GCI by decoupling piston motion from cylinder scavenging, allowing for flexible and independent control of cylinder residual fraction and temperature leading to improved low load combustion. In addition, the high peak cylinder pressure and noise challenges at high-load operation are mitigated by the lower BMEP operation and faster heat release for the same pressure rise rate of the OP Engine. These advantages further solidify the performance benefits of the OP Engine and demonstrate the near-term feasibility of advanced combustion technologies, enabled by the opposed-piston architecture. This paper presents initial results from a steady state testing on a brand new 2.7L OP GCI multi-cylinder engine. A part of the recipe for successful GCI operation calls for high compression ratio, leading to higher combustion stability at low-loads, higher efficiencies, and lower cycle HC+NOx emissions. In addition, initial results on catalyst light-off mode with GCI are also presented. The OP Engine’s architectural advantages enable faster and earlier catalyst light-off while producing low emissions, which further improves cycle emissions and fuel consumption over conventional engines.

Fuel efficiency analysis and peak pressure rise rate improvement for neat n-butanol injection strategies

2016 ◽  
Vol 231 (1) ◽  
pp. 50-65 ◽  
Author(s):  
Marko Jeftić ◽  
Zhenyi Yang ◽  
Graham T Reader ◽  
Ming Zheng
Keyword(s):  
Carbon Monoxide ◽  
Peak Pressure ◽  
Pressure Rise ◽  
Single Shot ◽  
Pilot Injection ◽  
Post Injection ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Main Injection ◽  
Injection Strategies

Engine tests were conducted to investigate the efficiency and the peak pressure rise rate performance of different fuel injection strategies for the direct injection of neat n-butanol in a compression ignition engine. Three different strategies were tested: a single-shot injection; a pilot injection; a post-injection. A single-shot injection timing sweep revealed that early injections had the highest indicated efficiency while late injections reduced the peak pressure rise rate at the cost of a slightly reduced thermal efficiency. Delayed single-shot injections also had increased emissions of nitrogen oxides, total hydrocarbon and carbon monoxide. Addition of a pilot injection had a negative effect on the peak pressure rise rate. Because of the low cetane number of butanol and the relatively lean and well-premixed air–fuel mixture, the pilot injection failed to autoignite and instead ignited simultaneously with the main injection. This resulted in slightly increased peak pressure rise rates and significantly increased unburned butanol hydrocarbon emissions. Conversely, the use of an early post-injection produced a noticeable engine power output and allowed the main injection to be shortened and the peak pressure rise rate to be substantially reduced. However, relatively early post-injections slightly reduced the indicated efficiency and increased the nitrogen oxide emissions and the carbon monoxide emissions compared with the single-shot injection strategy. These results recommended the use of a single-shot injection for low loads and medium loads owing to a superior thermal efficiency and suggested that the application of a post-injection may be more suited to high-load conditions because of the substantially reduced peak pressure rise rates.

Sign in / Sign up

Export Citation Format

Share Document