Improved Accuracy in Jet Impingement Heat Transfer Experiments Considering the Layer Thicknesses of a Triple Thermochromic Liquid Crystal Coating

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Alexandros Terzis ◽  
Stavros Bontitsopoulos ◽  
Peter Ott ◽  
Jens von Wolfersdorf ◽  
Anestis I. Kalfas
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Thickness Gauge ◽  
Thermochromic Liquid Crystal ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Paint Thickness

This paper examines the applicability of a triple layer of thermochromic liquid crystals (TLCs) for the determination of local heat transfer coefficients using the transient liquid crystal (LC) technique. The experiments were carried out in a narrow impingement channel, typically used for turbine blade cooling applications. Three types of narrow bandwidth LCs (1 °C range) of 35 °C, 38 °C, and 41 °C were individually painted on the target plate of the cooling cavity and the overall paint thickness was accurately determined with an integral coating thickness gauge. The 1D transient heat conduction equation is then implicitly solved for each individual TLC layer on its realistic depth on the painted surface. Local heat transfer coefficients are therefore calculated three times for the same location in the flow improving the measurement accuracy, especially at regions where the LC detection times are too short (stagnation points) or too long (wall-jet regions). The results indicate that if multiple LC layers are used and the paint thickness is not considered, the heat transfer coefficients can be significantly underestimated.

Three-Dimensional Transient Heat Conduction Equation Solution for Accurate Quantification of Heat Transfer Coefficient in Transient Liquid Crystal Experiments

2019 ◽  
Author(s):  
Shoaib Ahmed ◽  
Prashant Singh ◽  
Srinath V. Ekkad
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Liquid Crystal ◽  
Transfer Coefficient ◽  
Three Dimensional ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Conduction Model

Abstract Liquid crystal thermography and infrared thermography techniques are typically employed to measure detailed surface temperatures, where local heat transfer coefficient (HTC) values are calculated by employing suitable conduction models. One such practice, which is very popular and easy to use, is the transient liquid crystal thermography using one-dimensional semi-infinite conduction model. In these experiments, a test surface with low thermal conductivity and low thermal diffusivity (e.g. acrylic) is used where a step-change in coolant air temperature is induced and surface temperature response is recorded. An error minimization routine is then employed to guess heat transfer coefficients of each pixel, where wall temperature evolution is known through an analytical expression. The assumption that heat flow in the solid is essentially in one-dimension, often leads to errors in HTC determination and this error depends on true HTC, wall temperature evolution and HTC gradient. A representative case of array jet impingement under maximum crossflow condition has been considered here. This heat transfer enhancement concept is widely used in gas turbine leading edge and electronics cooling. Jet impingement is a popular cooling technique which results in high convective heat rates and has steep gradients in heat transfer coefficient distribution. In this paper, we have presented a procedure for solution of three-dimensional transient conduction equation using alternating direction implicit method and an error minimization routine to find accurate heat transfer coefficients at relatively lower computational cost. The HTC results obtained using 1D semi-infinite conduction model and 3D conduction model were compared and it was found that the heat transfer coefficient obtained using the 3D model was consistently higher than the conventional 1D model by 3–16%. Significant deviations, as high as 8–20% in local heat transfer at the stagnation points of the jets were observed between h1D and h3D.

A Comparison of the Transient and Heated-Coating Methods for the Measurement of Local Heat Transfer Coefficients on a Pin Fin

1989 ◽  
Vol 111 (4) ◽  
pp. 877-881 ◽  
Author(s):  
J. W. Baughn ◽  
P. T. Ireland ◽  
T. V. Jones ◽  
N. Saniei
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Uniform Heat Flux ◽  
Fluid Temperature ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
The Difference

Measurements of the local heat transfer coefficients on a pin fin (i.e., a short cylinder in crossflow) in a duct have been made using two methods, both of which employ liquid crystals to map an isotherm on the surface. The transient method uses the liquid crystal to determine the transient response of the surface temperature to a change in the fluid temperature. The local heat transfer coefficient is determined from the surface response time and the thermal properties of the substrate. The heated-coating method uses an electrically heated coating (vacuum-deposited gold in this case) to provide a uniform heat flux, while the liquid crystal is used to locate an isotherm on the surface. The two methods compare well, especially the value obtained near the center stagnation point of the pin fin where the difference in the thermal boundary condition of the two methods has little effect. They are close but differ somewhat in other regions.

scholarly journals A Comparison of the Transient and Heated-Coating Methods for the Measurement of Local Heat Transfer Coefficients on a Pin Fin

1988 ◽  
Author(s):  
J. W. Baughn ◽  
P. T. Ireland ◽  
T. V. Jones ◽  
N. Saniei
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Uniform Heat Flux ◽  
Fluid Temperature ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
The Difference

Measurements of the local heat transfer coefficients on a pin fin (i.e., a short cylinder in crossflow) in a duct have been made using two methods, both of which employ liquid crystals to map an isotherm on the surface. The transient method uses the liquid crystal to determine the transient response of the surface temperature to a change in the fluid temperature. The local heat transfer coefficient is determined from the surface response time and the thermal properties of the substrate. The heated-coating method uses an electrically heated coating (vacuum-deposited gold in this case) to provide a uniform heat flux while the liquid crystal is used to locate an isotherm on the surface. The two methods compare well, especially the value obtained near the center stagnation point of the pin fin where the difference in the thermal boundary condition of the two methods has little effect. They are close but differ somewhat in other regions.

The Effect of Regulating Elements on Convective Heat Transfer along Shaped Heat Exchange Surfaces

2013 ◽  
Vol 34 (1) ◽  
pp. 5-16 ◽  
Author(s):  
Jozef Cernecky ◽  
Jan Koniar ◽  
Zuzana Brodnianska
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Cfd Simulation ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Temperature Fields ◽  
Transfer Coefficients ◽  
Heat Transfer Intensification ◽  
Heat Transfer Coefficients ◽  
Forced Air

Abstract The paper deals with a study of the effect of regulating elements on local values of heat transfer coefficients along shaped heat exchange surfaces with forced air convection. The use of combined methods of heat transfer intensification, i.e. a combination of regulating elements with appropriately shaped heat exchange areas seems to be highly effective. The study focused on the analysis of local values of heat transfer coefficients in indicated cuts, in distances expressed as a ratio x/s for 0; 0.33; 0.66 and 1. As can be seen from our findings, in given conditions the regulating elements can increase the values of local heat transfer coefficients along shaped heat exchange surfaces. An optical method of holographic interferometry was used for the experimental research into temperature fields in the vicinity of heat exchange surfaces. The obtained values correspond very well with those of local heat transfer coefficients αx, recorded in a CFD simulation.

scholarly journals Heat Transfer Coefficient Determination in a Gravity Die Casting Process with Local Air Gap Formation and Contact Pressure Using Experimental Evaluation and Numerical Simulation

2021 ◽  
Author(s):  
T. Vossel ◽  
N. Wolff ◽  
B. Pustal ◽  
A. Bührig-Polaczek ◽  
M. Ahmadein
Keyword(s):  
Heat Transfer ◽  
Contact Pressure ◽  
Local Heat Transfer ◽  
Casting Process ◽  
Local Heat ◽  
Air Gap ◽  
Gap Formation ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Die Casting Process

AbstractAnticipating the processes and parameters involved for accomplishing a sound metal casting requires an in-depth understanding of the underlying behaviors characterizing a liquid melt solidifying inside its mold. Heat balance represents a major factor in describing the thermal conditions in a casting process and one of its main influences is the heat transfer between the casting and its surroundings. Local heat transfer coefficients describe how well heat can be transferred from one body or material to another. This paper will discuss the estimation of these coefficients in a gravity die casting process with local air gap formation and heat shrinkage induced contact pressure. Both an experimental evaluation and a numerical modeling for a solidification simulation will be performed as two means of investigating the local heat transfer coefficients and their local differences for regions with air gap formation or contact pressure when casting A356 (AlSi7Mg0.3).

scholarly journals Condensation inside smooth horizontal tubes: Part 1. Survey of the methods of heat-exchange prediction

2015 ◽  
Vol 19 (5) ◽  
pp. 1769-1789 ◽  
Author(s):  
Volodymyr Rifert ◽  
Volodymyr Sereda
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Film Condensation ◽  
Experimental Investigations ◽  
Phase Flow ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Horizontal Tubes

Survey of the works on condensation inside smooth horizontal tubes published from 1955 to 2013 has been performed. Theoretical and experimental investigations, as well as more than 25 methods and correlations for heat transfer prediction are considered. It is shown that accuracy of this prediction depends on the accuracy of volumetric vapor content and pressure drop at the interphase. The necessity of new studies concerning both local heat transfer coefficients and film condensation along tube perimeter and length under annular, stratified and intermediate regimes of phase flow was substantiated. These characteristics being defined will allow determining more precisely the boundaries of the flow regimes and the methods of heat transfer prediction.

Heat Transfer and Pressure Drop Correlations for Square Channels With 45 Deg Ribs at High Reynolds Numbers

2009 ◽  
Vol 131 (7) ◽  
Author(s):  
Akhilesh P. Rallabandi ◽  
Huitao Yang ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Turbine Blade Cooling ◽  
Square Channel ◽  
Heat Transfer Coefficients ◽  
High Reynolds ◽  
Cooling Passage

Systematic experiments are conducted to measure heat transfer enhancement and pressure loss characteristics on a square channel (simulating a gas turbine blade cooling passage) with two opposite surfaces roughened by 45 deg parallel ribs. Copper plates fitted with a silicone heater and instrumented with thermocouples are used to measure regionally averaged local heat transfer coefficients. Reynolds numbers studied in the channel range from 30,000 to 400,000. The rib height (e) to hydraulic diameter (D) ratio ranges from 0.1 to 0.18. The rib spacing (p) to height ratio (p/e) ranges from 5 to 10. Results show higher heat transfer coefficients at smaller values of p/e and larger values of e/D, though at the cost of higher friction losses. Results also indicate that the thermal performance of the ribbed channel falls with increasing Reynolds numbers. Correlations predicting Nusselt number (Nu) and friction factor (f¯) as a function of p/e, e/D, and Re are developed. Also developed are correlations for R and G (friction and heat transfer roughness functions, respectively) as a function of the roughness Reynolds number (e+), p/e, and e/D.

Sign in / Sign up

Export Citation Format

Share Document