Interactions of Separation Bubble With Oncoming Wakes by Large-Eddy Simulation

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
S. Sarkar ◽  
Harish Babu ◽  
Jasim Sadique
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Leading Edge ◽  
Constant Thickness ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Past A Cylinder ◽  
Rotor Stator Interaction

The unsteady flow physics and heat transfer characteristics due to interactions of periodic passing wakes with a separated boundary layer are studied using large-eddy simulation (LES). A series of airfoils of constant thickness with rounded leading edge are employed to obtain the separated boundary layer. Wake data extracted from precursor LES of flow past a cylinder are used to replicate a moving bar that generates wakes in front of a cascade (in this case, an infinite row of the model airfoils). This setup is a simplified representation of the rotor–stator interaction in turbomachinery. With a uniform inlet, the laminar boundary layer separates near the leading edge, undergoes transition due to amplification of disturbances, becomes turbulent, and finally reattaches forming a separation bubble. In the presence of oncoming wakes, the characteristics of the separated boundary layer have changed and the impinging wakes are found to be the mechanism affecting the reattachment. Phase-averaged results illustrate the periodic behavior of both flow and heat transfer. Large undulations in the phase-averaged skin friction and Nusselt number distributions can be attributed to the excitation of the boundary layer by convective wakes forming coherent vortices, which are being shed and convect downstream. Further, the transition of the separated boundary layer during the wake-induced path is governed by a mechanism that involves the convection of these vortices followed by increased fluctuations, where viscous effect is substantial.

Large Eddy Simulation on the Interactions of Wake and Film-Cooling Near a Leading Edge

2014 ◽  
Author(s):  
Harish Babu ◽  
S. Sarkar
Keyword(s):  
Large Eddy Simulation ◽  
Film Cooling ◽  
Vortex Pair ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Constant Thickness ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Past A Cylinder ◽  
Rotor Stator Interaction

The unsteady flow physics due to interactions between a separated shear layer and film cooling jet apart from excitation of periodic passing wake are studied using Large Eddy Simulation (LES). An aerofoil of constant thickness with rounded leading edge induced flow separation, while film cooling jets were injected normal to the crossflow a short distance downstream of the blend point. Wake data extracted from precursor LES of flow past a cylinder are used to replicate a moving bar that generates wakes in front of a cascade (in this case, an infinite row of the model aerofoils). This setup is a simplified representation of rotor-stator interaction in a film cooled gas turbine. The results of numerical simulation are presented to elucidate the formation, convection and breakdown of flow structures associated with the highly anisotropic flow involved in film cooling perturbed by convective wakes. The various vortical structures namely, horseshoe vortex, roller vortex, upright wake vortex, counter rotating vortex pair and DSSN vortex associated with film cooling are resolved. The effects of wake on the evolution of these structures are then discussed.

Large Eddy Simulation on the Interactions of Wake and Film-Cooling Near a Leading Edge

2014 ◽  
Vol 137 (1) ◽  
Author(s):  
S. Sarkar ◽  
Harish Babu
Keyword(s):  
Large Eddy Simulation ◽  
Film Cooling ◽  
Vortex Pair ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Constant Thickness ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Past A Cylinder ◽  
Downward Spiral

The unsteady flow physics due to interactions between a separated shear layer and film cooling jet apart from excitation of periodic passing wake are studied using large eddy simulation (LES). An aerofoil of constant thickness with rounded leading edge induced flow separation, while film cooling jets were injected normal to the crossflow a short distance downstream of the blend point. Wake data extracted from precursor LES of flow past a cylinder are used to replicate a moving bar that generates wakes in front of a cascade (in this case, an infinite row of the model aerofoils). This setup is a simplified representation of rotor-stator interaction in a film cooled gas turbine. The results of numerical simulation are presented to elucidate the formation, convection and breakdown of flow structures associated with the highly anisotropic flow involved in film cooling perturbed by convective wakes. The various vortical structures namely, horseshoe vortex, roller vortex, upright wake vortex, counter rotating vortex pair (CRVP), and downward spiral separation node (DSSN) vortex associated with film cooling are resolved. The effects of wake on the evolution of these structures are then discussed.

Interactions of Separation Bubble With Oncoming Wakes by LES

2011 ◽  
Author(s):  
S. Sarkar ◽  
Jasim Sadique
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Shear Layer ◽  
Separation Bubble ◽  
Leading Edge ◽  
Flat Plates ◽  
Flow Past A Cylinder ◽  
Periodic Behaviour ◽  
Rotor Stator Interaction ◽  
Multiple Bubbles

The unsteady flow physics and heat transfer characteristics due to interactions of periodic passing wakes with a separated boundary layer are studied with the help of Large-eddy simulations (LES). A flat plate with a semicircular leading edge is employed to obtain the separated boundary layer. Wake data extracted from precursor LES of flow past a cylinder are used to replicate a moving bar that generates wakes in front of a cascade (in this case an infinite row of flat plates). This setup is a simplified representation of the rotor-stator interaction in turbomachinery. With a uniform inlet, the laminar boundary layer separates near the leading edge, undergoes transition due to amplification of the disturbances, becomes turbulent and finally reattaches forming a bubble. In the presence of oncoming wakes, the characteristics of the separated layer have changed and the impinging wakes are found to be the mechanism affecting the reattachment. Phase averaged results illustrate the periodic behaviour of both flow and heat transfer. Large undulations in the phase-averaged skin friction and Nusselt number distributions can be attributed to the excitation of separated shear layer by convective wakes forming coherent vortices, which are being shed and convect downstream. This interaction also breaks the bubble into multiple bubbles. Further, the transition of the shear layer during the wake-induced path is governed by a mechanism that involves the convection of these vortices followed by increased fluctuations.

Leading Edge Contamination of a C-D Compressor Blade Using Large Eddy Simulation

2020 ◽  
Author(s):  
S. Katiyar ◽  
S. Sarkar
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Leading Edge ◽  
Adverse Pressure Gradient ◽  
Suction Surface ◽  
Local Flow ◽  
Flow Acceleration ◽  
Eddy Simulation ◽  
Large Eddy

Abstract A large-eddy simulation (LES) is employed here to predict the flow field over the suction surface of a controlled-diffusion (C-D) compressor stator blade following the experiment of Hobson et al. [1]. When compared with the experiment, LES depicts a separation bubble (SB) in the mid-chord region of the suction surface, although discrepancies exist in Cp. Further, the LES resolves the growth of boundary layer over the mid-chord and levels of turbulence intensity with an acceptable limit. What is noteworthy that LES also resolves a tiny SB near the leading-edge at the designed inflow angle of 38.3°. The objective of the present study is to assess how this leading-edge bubble influences the transition and development of boundary layer on the suction surface before the mid-chord. It appears that the separation at leading-edge suddenly enhances the perturbation levels exciting development of boundary layer downstream. The boundary layer becomes pre-transitional followed by a decay of fluctuations up to 30% of chord attributing to the local flow acceleration. Further, the boundary layer appears like laminar after being relaxed from the leading edge excitation near the mid-chord. It separates again because of the adverse pressure gradient, depicting augmentation of turbulence followed by the breakdown at about 70% of chord.

Effects of incidence angle on a low-pressure turbine blade boundary layer evolution through large eddy simulation

2018 ◽  
Vol 232 (6) ◽  
pp. 722-734 ◽  
Author(s):  
Yunfei Wang ◽  
Xiuming Sui ◽  
Kai Zhang ◽  
Xiaorong Xiang ◽  
Qingjun Zhao
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Coherent Structures ◽  
Separation Bubble ◽  
Incidence Angle ◽  
Leading Edge ◽  
Pressure Side ◽  
Low Pressure Turbine ◽  
Eddy Simulation ◽  
Large Eddy

The evolution mechanism of the boundary layer and coherent structures in a low-pressure turbine blade is discussed. Five different incidence angles over the T106A blade for a Mach number Ma = 0.404 and Reynolds number Re = 0.6 × 105 (based on the axial chord and outlet velocity) are performed using large eddy simulation method. The calculation results at +7.8 incidence angle are agreed well with the experimental and direct numerical simulation data. The influence of the incidence angle on the flow field is mainly shown at the front of the suction side and pressure side. As the incidence angle changes from positive to negative, the separation bubble near the leading edge disappears and the blade loading decreases gradually. When the incidence angle reduces to −5°, separation bubble appears near the leading edge of the pressure side. At the case of incidence angle equaling −10°, the length of time-averaged separation bubble on the pressure side grows to 39% axial chord and the evolution process of the coherent structures is extremely complex. The spanwise vortexes roll up near the leading edge and gradually evolve into streamwise vortexes. High-energy fluid in the main flow was driven to near-wall zone by the rotating effect of streamwise vortexes, which increases the fluid momentum inside the boundary layer. The streamwise vortexes are stretched by the strong acceleration of the flow until they transport to the trailing edge.

The onset of dynamic stall at a high, transitional Reynolds number

2018 ◽  
Vol 861 ◽  
pp. 860-885 ◽  
Author(s):  
S. I. Benton ◽  
M. R. Visbal
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Leading Edge ◽  
Dynamic Stall ◽  
Turbulent Shear ◽  
Eddy Simulation ◽  
Turbulent Separation ◽  
Large Eddy

Dynamic stall due to a ramp-type pitching motion is investigated on the NACA 0012 airfoil at chord Reynolds number of $Re_{c}=1.0\times 10^{6}$ through the use of wall-resolved large-eddy simulation. Emphasis is placed on the unsteady boundary-layer interactions that develop as the airfoil approaches stall. At this Reynolds number it is shown that turbulent separation moves upstream across much of the airfoil suction surface. When turbulent separation reaches the leading-edge separation bubble, a bursting event is initiated leading to a strong coherent leading-edge vortex structure. This vortex wraps up the turbulent shear layer to form a large dynamic stall vortex. The use of large-eddy simulation elucidates the roll of the laminar separation bubble in defining the onset of the dynamic stall process. Comparisons are made to identical simulations at lower Reynolds numbers of $Re_{c}=0.2\times 10^{6}$ and $0.5\times 10^{6}$. This comparison demonstrates trends in the boundary-layer mechanics that explain the sensitivity of the dynamic stall process to Reynolds number.

Large Eddy Simulation of Boundary Layer Separation and Reattachment in a LPT Blade at Different Incidence Angles

2015 ◽  
Author(s):  
Yunfei Wang ◽  
Huaping Liu ◽  
Yanping Song ◽  
Fu Chen
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Incidence Angle ◽  
Leading Edge ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Reattachment Point ◽  
Eddy Simulation ◽  
Large Eddy

In order to predict the phenomenon of laminar flow separation, transition and reattachment in a high-lift low-pressure turbine (LPT), a self-developed large eddy simulation program to solve three dimensional compressible N-S equations was used to simulate the flow structures in T106A LPT blade passage. The outlet Mach number is 0.4 and the Reynolds number is 1.1×105 based on the exit isentropic velocity and the axial chord. The distributions of the time-averaged static pressure coefficient, kinetic loss coefficient and wall shear stress on the blade surface at +7.8° incidence angle agree well with the results of experiment and direct numerical simulation (DNS). The locations of laminar separation and reattachment point occur around 83.6% and 97% axial chord respectively. The evolutionary process of spanwise vorticity and large-scale coherent structure near the trailing edge on the suction side in one period indicates that the two-dimensional shear layer is gradually unstable as a result of spanwise fluctuation and Kelvin-Helmholtz (K-H) instability. The boundary layer separates from the suction surface and the hairpin vortex appears in succession, which leads to transition to turbulence. Analysis of the incidence angle effect on the boundary layer separation point as well as separation bubble scale was also performed. A small scale separation bubble exists around the leading edge at positive incidences. As the incidence angle changes from positive to negative, the separation bubble near the leading edge disappears and the boundary layer thickness reduces gradually. The separation point at the rear part of suction side moves downstream, yet the reattachment point barely changes. The Reynolds stress and turbulent kinetic energy profiles change dramatically at zero and positive incidence. This illustrates that the incidence angle has great influence on the development of the boundary layer and the flow field structures.

scholarly journals Large Eddy Simulation of Microvortex Generators in a Turbulent Boundary Layer

2021 ◽  
Vol 143 (5) ◽  
Author(s):  
Andrew P. Heffron ◽  
John J. Williams ◽  
Eldad J. Avital
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Vortex Formation ◽  
Leading Edge ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Features ◽  
Challenging Environment

Abstract This study investigates the flow physics on microvortex generators (MVGs) in order to improve their performance in turbulent boundary layers (TBLs). TBLs can be a challenging environment for MVGs because of the streamwise length of the generated vortex and the increased parasitic drag of the MVGs. Large eddy simulation (LES) is used to properly resolve the turbulent boundary layer of a flat-plate with a zero-pressure gradient and MVG vane. Three different vane-types are investigated (e423-Mod, triangular, and rectangular vanes) and are studied in a single vane configuration. Important flow features such as a separation bubble on the leading edge of the rectangular vanes which introduced unsteadiness into the vortex formation and degraded the MVG's efficiency was observed. The e423-Mod and triangular vanes were observed to be more aerodynamically efficient. The triangular vane was found to be the most efficient when evaluated immediately downstream of the vane. However, the vortex from the triangular vane decayed very rapidly due to it being formed very close to the wall which degraded its efficiency further downstream. The e423-Mod vane avoided this problem but its drag was very high relative to the strength of the generated vortex and its vortex experienced a brief period of rapid decay immediately downstream decreasing its efficiency. Further downstream, the vortex of the rectangular vane at 16 deg became the most efficient through a combination of low vane drag and low vortex decay in the TBL, demonstrating the need to consider a range of issues when designing an MVG.

Large Eddy Simulation of Film Cooling for the Real Additive Manufactured Fan-Shaped Holes

2020 ◽  
Author(s):  
Wei Shi ◽  
Xueying Li ◽  
Lang Wang ◽  
Jing Ren ◽  
Hongde Jiang
Keyword(s):  
Heat Transfer ◽  
Large Eddy Simulation ◽  
Film Cooling ◽  
Separation Bubble ◽  
Leading Edge ◽  
Widespread Application ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Eddy Simulation ◽  
Large Eddy

Abstract Additive Manufacturing (AM) is a process for making complex parts that were once difficult to machine using traditional manufacturing processes such as forging, casting, and welding. As a new and promising processing technology, AM is being increasingly applied to the manufacturing of high temperature turbine parts. However, before the widespread application of AM can become feasible, the influence of such processes on the performance of turbine hot ends — especially during the film cooling flow heat transfer — requires further study. This paper focuses a large eddy simulation study done in order to understand the physical phenomena involved in the random roughness caused by the AM of fan-shaped film holes. This paper proposes a set of workflows to connect the AM, CFD simulation, Computed Tomography (CT) and reverse modeling, so that the effect of AM on the flow and heat transfer of film cooling can be studied. The results of this preliminary workflow reveal several observations. First, that the film cooling effectiveness (η) of AM fan-shaped holes decreases. The area averaged η of the ideal hole is 0.32, while the area averaged cooling effectiveness of the AM hole is 0.29. As such, the η of the AM fan-shaped hole has a significant bifurcation phenomenon. This is because the separation bubble in-tube moves forward, and blocks the flow channel, which bifrucates the flow in-tube. Second, a pressure gradient towards the trailing edge generated at a random rough surface near the leading edge squeezes the fluid. The combined effect of these two mechanisms causes the fluid to flow out of the air film pores mainly from the leading edge with a smaller lateral expansion.

scholarly journals Large-eddy simulation of laminar transonic buffet

2018 ◽  
Vol 850 ◽  
pp. 156-178 ◽  
Author(s):  
Julien Dandois ◽  
Ivan Mary ◽  
Vincent Brion
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Oscillation Amplitude ◽  
Boundary Layer Separation ◽  
Stream Velocity ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Shock Oscillation ◽  
Transonic Buffet

A large-eddy simulation of laminar transonic buffet on an airfoil at a Mach number $M=0.735$, an angle of attack $\unicode[STIX]{x1D6FC}=4^{\circ }$, a Reynolds number $Re_{c}=3\times 10^{6}$ has been carried out. The boundary layer is laminar up to the shock foot and laminar/turbulent transition occurs in the separation bubble at the shock foot. Contrary to the turbulent case for which wall pressure spectra are characterised by well-marked peaks at low frequencies ($St=f\cdot c/U_{\infty }\simeq 0.06{-}0.07$, where $St$ is the Strouhal number, $f$ the shock oscillation frequency, $c$ the chord length and $U_{\infty }$ the free-stream velocity), in the laminar case, there are also well-marked peaks but at a much higher frequency ($St=1.2$). The shock oscillation amplitude is also lower: 6 % of chord and limited to the shock foot area in the laminar case instead of 20 % with a whole shock oscillation and intermittent boundary layer separation and reattachment in the turbulent case. The analysis of the phase-averaged fields allowed linking of the frequency of the laminar transonic buffet to a separation bubble breathing phenomenon associated with a vortex shedding mechanism. These vortices are convected at $U_{c}/U_{\infty }\simeq 0.4$ (where $U_{c}$ is the convection velocity). The main finding of the present paper is that the higher frequency of the shock oscillation in the laminar regime is due to a different mechanism than in the turbulent one: laminar transonic buffet is due to a separation bubble breathing phenomenon occurring at the shock foot.

Sign in / Sign up

Export Citation Format

Share Document