Frictional Pressure Drop Correlations for Single-Phase Flow, Condensation, and Evaporation in Microfin Tubes

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Zan Wu ◽  
Bengt Sundén
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Single Phase ◽  
Flow Boiling ◽  
Phase Flow ◽  
Single Phase Flow ◽  
Frictional Pressure Drop ◽  
Friction Factors ◽  
Flow Condensation ◽  
Microfin Tubes

Experimental single-phase, condensation, and evaporation (flow boiling) pressure drop data from the literature and our previous studies were collected to evaluate previous frictional pressure drop correlations for horizontal microfin tubes of different geometries. The modified Ravigururajan and Bergles correlation, by adopting the Churchill model to calculate the smooth-tube friction factor and by using the hydraulic diameter in the Reynolds number, can predict single-phase turbulent frictional pressure drop data relatively well. Eleven pressure drop correlations were evaluated by the collected database for condensation and evaporation. Correlations originally developed for condensation and evaporation in smooth tubes can be suitable for microfin tubes if the friction factors in the correlations were calculated by the Churchill model to include microfin effects. The three most accurate correlations were recommended for condensation and evaporation in microfin tubes. The Cavallini et al. correlation and the modified Friedel correlation can give good predictions for both condensation and evaporation. However, some inconsistencies were found, even for the recommended correlations.

Frictional Pressure Drop Correlations for Single-Phase Flow, Condensation and Evaporation in Microfin Tubes

2014 ◽  
Author(s):  
Zan Wu ◽  
Bengt Sundén
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Single Phase ◽  
Flow Boiling ◽  
Phase Flow ◽  
Single Phase Flow ◽  
Frictional Pressure Drop ◽  
Friction Factors ◽  
Flow Condensation ◽  
Microfin Tubes

Experimental single-phase, condensation and evaporation (flow boiling) pressure drop data from the literature and our previous studies were collected to evaluate previous frictional pressure drop correlations for horizontal microfin tubes of different geometries. The modified Ravigururajan and Bergles correlation, by adopting the Churchill model to calculate the smooth-tube friction factor and by using the hydraulic diameter in the Reynolds number, can predict single-phase turbulent frictional pressure drop data relatively well. Eleven pressure drop correlations were evaluated by the collected database for condensation and evaporation. Correlations originally developed for condensation and evaporation in smooth tubes can be suitable for microfin tubes if the friction factors in the correlations were calculated by the Churchill model to include microfin effects. The three most accurate correlations were recommended for condensation and evaporation in microfin tubes, respectively. The Cavallini et al. correlation and the modified Friedel correlation can give good predictions for both condensation and evaporation. However, some inconsistencies were found, even for the recommended correlations.

A numerical investigation on single-phase flow characteristics and frictional pressure drop in helical pipes

2020 ◽  
Vol 52 (4) ◽  
pp. 045505
Author(s):  
Pengxin Cheng ◽  
Nan Gui ◽  
Xingtuan Yang ◽  
Jiyuan Tu ◽  
Shengyao Jiang ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Numerical Investigation ◽  
Single Phase ◽  
Flow Characteristics ◽  
Phase Flow ◽  
Single Phase Flow ◽  
Frictional Pressure Drop

Thermofluid Characteristics of Two-Phase Microgap Coolers

2007 ◽  
Author(s):  
Dae W. Kim ◽  
Emil Rahim ◽  
Avram Bar-Cohen ◽  
Bongtae Han
Keyword(s):  
Heat Transfer ◽  
Numerical Model ◽  
Pressure Drop ◽  
Single Phase ◽  
Flow Boiling ◽  
Phase Flow ◽  
Dissolved Gas ◽  
Single Phase Flow ◽  
Two Phase ◽  
Phase Water

The thermofluid characteristics of a chip-scale microgap cooler, including single-phase flow of water and FC-72 and flow boiling of FC-72, are explored. Heat transfer and pressure drop results for single phase water are used to validate a detailed numerical model and, together with the convective FC-72 data, establish a baseline for microgap cooler performance. Experimental results for single phase water and FC-72 flowing in 120 μm, 260 μm and 600 μm microgap coolers, 31mm wide by 34mm long, at velocities of 0.1 – 2 m/s are reported. “Pseudo-boiling” driven by dissolved gas and flow boiling of FC-72 are found to provide significant enhancement in heat transfer relative to theoretical single phase values.

Heat Transfer Augmentation in 3D Inner Finned Helical Tube

Volume 3 ◽  
2004 ◽  
Author(s):  
Longjian Li ◽  
Wenzhi Cui ◽  
Quan Liao ◽  
Mingdao Xin ◽  
Tien-Chien Jen ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Boiling Heat Transfer ◽  
Flow Resistance ◽  
Single Phase ◽  
Flow Boiling ◽  
Phase Flow ◽  
Single Phase Flow ◽  
Helical Tube ◽  
Helical Tubes

Experiments were performed to investigate the performance enhancement of single-phase flow and boiling heat transfer in the 3D inner finned helical tubes. The tests for single-phase flow and heat transfer were carried out in the helical tubes with a curvature of 0.0663 and a length of 1.15m, the range of the Reynolds number examined varies from 1000 to 8500. In comparison to the smooth helical tube, the experimental results of two finned helical tubes with different inner fin geometry showed that the heat transfer and flow resistance in the 3D inner finned helical tube gains greater augmentation. Within the measured range of Reynolds number, the average augmentation ratio of heat transfer of the two finned tubes are 71% and 103%, compared with the smooth helical tube, and 90% and 140% for flow resistance, respectively. The tests for flow boiling heat transfer was carried out in the 3D inner finned helical tube with a curvature of 0.0605 and a length of 0.668m. Compared with that in the smooth helical tube, the boiling heat transfer coefficient in the 3D inner finned helical tube is increased by 40%∼120% under varied mass flow rate and wall heat flux conditions, meanwhile, the flow resistance coefficient increased by 18%∼119%.

Thermal and Hydrodynamic Characteristics of Single-Phase Flow and Flow Boiling in a Staggered Micro-Pin-Fin Array

2008 ◽  
Author(s):  
Weilin Qu
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Single Phase ◽  
Flow Boiling ◽  
Hydrodynamic Characteristics ◽  
Inlet Temperature ◽  
Phase Flow ◽  
Single Phase Flow ◽  
Pin Fin ◽  
Pin Fin Array

This study concerns thermal and hydrodynamic characteristics of water single-phase flow and flow boiling in a micro-pin-fin array. An array of 1950 staggered square micro-pin-fins with a 200×200 μm2 cross-section by a 670 μm height were fabricated into a copper heat sink test section. Two inlet temperatures of 30 °C and 60 °C, and six maximum mass velocities for each inlet temperature, ranging from 183 to 420 kg/m2s, were tested. The corresponding inlet Reynolds number ranged from 45.9 to 179.6. General characteristics of single-phase flow and flow boiling were described. Predictive tools were proposed for single-phase heat transfer coefficient and pressure drop. Unique features of flow boiling heat transfer in the micro-pin-fin array were identified. The classic Lockhart-Martinelli correlation incorporating a single-phase micro-pin-fin friction factor correlation and the laminar liquid–laminar vapor combination assumption was used to predict two-phase pressure drop in the micro-pin-fin array. The predictions agreed well with the experimental data.

scholarly journals PREDICTION OF PRESSURE DROP IN HELICAL COIL WITH SINGLE PHASE FLOW OF NON-NEWTONIAN FLUID

2012 ◽  
pp. 256-261
Author(s):  
B.S.V.S.R. KRISHNA
Keyword(s):  
Pressure Drop ◽  
Single Phase ◽  
Methyl Cellulose ◽  
Helix Angle ◽  
Helical Coil ◽  
Phase Flow ◽  
Single Phase Flow ◽  
Number Range ◽  
Frictional Pressure Drop ◽  
Carboxy Methyl

The pressure drop of single phase was studied experimentally with non-Newtonian fluids of Carboxy Methyl Cellulose (CMC). Single helical coil with five different helix angles were used in this study to identify the effect of helix angle on pressure drop. The effect of helix angle is significant in moderate and high generalized Dean’s number of laminar region. The effect is insignificant in low generalized Dean’s number range and turbulent region. Correlations were developed for predicting the frictional pressure drop in laminar and turbulent regions.

Sign in / Sign up

Export Citation Format

Share Document