Conjugate Heat Transfer in Latent Heat Thermal Storage System With Cross Plate Fins

2015 ◽  
Vol 137 (10) ◽  
Author(s):  
Rajesh Alayil ◽  
C. Balaji
Keyword(s):  
Heat Transfer ◽  
Latent Heat ◽  
Phase Change Materials ◽  
Storage System ◽  
Thermal Storage ◽  
High Heat ◽  
Heat Fluxes ◽  
Isothermal Conditions ◽  
Latent Heat Capacity ◽  
Composite Heat

Latent heat thermal storage systems (LHTS) utilize their latent heat capacity to dissipate high heat fluxes while maintaining quasi-isothermal conditions. Phase change materials (PCMs) absorb a large amount of energy during their phase transformation from solid to liquid, maintaining quasi-isothermal conditions. However, they are often beset with low thermal conductivities which necessitate the use of a thermal conductivity enhancer (TCE) as it is impossible to design a device that can completely avoid sensible heat in the premelting or postmelting phase. In this study, the heat transfer performance of LHTS with cross plate fins as a TCE is numerically investigated for different values of fin thicknesses and fin numbers along the length and breadth. A hybrid artificial neural network coupled genetic algorithm (ANN–GA) is then used to obtain the optimized dimensions for the composite heat sink with cross plate fins as TCE for a fixed volume and a specific heat flux input. The numerically optimized configuration is finally validated with in-house experiments.

Numerical and Experimental Analysis of a PCM Thermal Storage System

2014 ◽  
Author(s):  
Adriano Sciacovelli ◽  
Vittorio Verda
Keyword(s):  
Latent Heat ◽  
Phase Change Materials ◽  
Heat Storage ◽  
Storage System ◽  
District Heating ◽  
Thermal Storage ◽  
Working Fluid ◽  
Latent Heat Storage ◽  
Thermal Enhancement ◽  
Charging And Discharging Processes

Phase-change materials (PCM) are particularly promising for thermal storage in energy systems where the working fluid is either characterized by small specific heat or small temperature difference. In these cases, sensible heat storage would involve small energy densities (i.e. energy per unit volume). Latent heat storage would allow one to reduce the volume of storage tanks, but also reduce problems related with thermal stratification. On the other hand, heat transfer in PCMs needs to be enhanced in order to complete the charging and discharging processes in reasonable time. This paper reports the numerical and experimental activity performed by the authors related with the design of latent heat storage systems for district heating applications. Among the various enhancement methods, fins present some technical advantages related with manufacturing and management, which make them suitable for the application in district heating systems. The following aspects are considered in this paper: 1) melting and solidification; 2) modeling approaches and validation; 3) thermal enhancement with circular, radial or Y-shaped fins.

scholarly journals Solar Salt Latent Heat Thermal Storage for a Small Solar Organic Rankine Cycle Plant

2019 ◽  
Vol 142 (3) ◽  
Author(s):  
Sol-Carolina Costa ◽  
Khamid Mahkamov ◽  
Murat Kenisarin ◽  
Mohammad Ismail ◽  
Kevin Lynn ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Latent Heat ◽  
Storage System ◽  
Organic Rankine Cycle ◽  
Heat Pipes ◽  
Rankine Cycle ◽  
Thermal Storage ◽  
Thermal Bonding ◽  
Solar Salt ◽  
Computational Fluid Dynamics Analysis

Abstract The design of the latent heat thermal storage system (LHTESS) was developed with a thermal capacity of about 100 kW h as a part of small solar plant based on the organic Rankine cycle (ORC). The phase change material (PCM) used is solar salt with the melting/solidification temperature of about 220 °C. Thermophysical properties of the PCM were measured, including its phase transition temperature, heat of fusion, specific heat, and thermal conductivity. The design of the thermal storage was finalized by means of the 3D computational fluid dynamics analysis. The thermal storage system is modular, and the thermal energy is delivered with the use of thermal oil, heated by Fresnel mirrors. The heat is transferred into and from the PCM in the casing using bidirectional heat pipes, filled with water. A set of metallic screens are installed in the box with the pitch of 8–10 mm to enhance the heat transfer from heat pipes to the PCM and vice-versa during the charging and discharging processes, which take about 4 h. This work presents a numerical study on the use of metallic fins without thermal bonding as a heat transfer enhancement method for the solar salt LHTESS. The results show that the absence of the thermal bonding between fins and heat pipes (there was a gap of 0.5 mm between them) did not result in a significant reduction of charging or discharging periods. As expected, aluminum fins provide better performance in comparison with steel ones due to the difference in the material conductivity. The main advantage observed for the case of using aluminum fins was the lower temperature gradient across the LHTESS.

Heat Transfer Characterization and Optimization of Latent Heat Thermal Storage System Using Fins for Medium Temperature Solar Applications

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Asmita Shinde ◽  
Sankalp Arpit ◽  
Pramod KM ◽  
Peddy V C. Rao ◽  
Sandip K. Saha
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Latent Heat ◽  
Optimum Design ◽  
Thermal Performance ◽  
Storage System ◽  
Thermal Storage ◽  
Solar Thermal ◽  
Medium Temperature ◽  
Fin Thickness

While solar thermal power plants are increasingly gaining attention and have demonstrated their applications, extending electricity generation after the sunset using phase change material (PCM) still remains a grand challenge. Most of the organic PCMs are known to possess high energy density per unit volume, but low thermal conductivity, that necessitates the use of thermal conductivity enhancers (TCEs) to augment heat transfer within PCM. In this paper, thermal performance and optimization of shell and tube heat exchanger-based latent heat thermal energy storage system (LHTES) using fins as TCE for medium temperature (<300 °C) organic Rankine cycle (ORC)-based solar thermal plant are presented. A commercial grade organic PCM, A164 with melting temperature of 168.7 °C is filled in the shell side and heat transfer fluid (HTF), Hytherm 600 flows through the tubes. A three-dimensional numerical model using enthalpy technique is developed to study the solidification of PCM, with and without fin. Further, the effect of geometrical parameters of fin, such as fin thickness, fin height, and number of fin on the thermal performance of LHTES, is studied. It is found that fin thickness and number of fin play significant role on the solidification process of PCM. Finally, the optimum design of the fin geometry is determined by maximizing the combined objective of HTF outlet temperature and solid fraction of PCM at the end of the discharging period. The latent heat thermal storage system with 24 fins, each of 1 mm thickness and 7 mm height, is found to be the optimum design for the given set of operating parameters.

Sign in / Sign up

Export Citation Format

Share Document