Experimental Investigation of Drag Reducing Fluid Flow in Annular Geometry Using Particle Image Velocimetry Technique

2015 ◽  
Vol 137 (8) ◽  
Author(s):  
Fabio E. Rodriguez Corredor ◽  
Majid Bizhani ◽  
Ergun Kuru
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Reynolds Numbers ◽  
Turbulent Kinetic Energy Budget ◽  
Flow Loop ◽  
Particle Image Velocimetry Technique ◽  
Mean Velocity ◽  
Image Velocimetry ◽  
Annular Geometry ◽  
Fully Developed Turbulent Flow

Fully developed turbulent flow of drag reducing fluids through a horizontal flow loop with concentric annular geometry was investigated using the particle image velocimetry (PIV) technique. Experiments were conducted at solvent Reynolds numbers ranged from 38,700 to 56,400. Axial mean velocity profile was found to be following the universal wall law close to the wall (i.e., y+ < 10), but it deviated from log law results with an increased slope in the logarithmic zone (i.e., y+ > 30). The study was also focused on turbulence statistics such as near wall Reynolds stress distribution, axial and radial velocity fluctuations, vorticity and turbulent kinetic energy budget.

An Experimental Investigation of Turbulent Water Flow in Concentric Annulus Using Particle Image Velocimetry Technique

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
F. E. Rodriguez-Corredor ◽  
Majid Bizhani ◽  
Mohammad Ashrafuzzaman ◽  
Ergun Kuru
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Maximum Velocity ◽  
Viscous Sublayer ◽  
Reynolds Stresses ◽  
Flow Loop ◽  
Particle Image Velocimetry Technique ◽  
Mean Velocity ◽  
Number Range ◽  
Image Velocimetry

Fully developed turbulent flow of water through a horizontal flow loop with concentric annular geometry was investigated using high resolution particle image velocimetry (PIV). Reynolds number range varied from 17,700 to 66,900. Axial mean velocity profile was found to be following the universal wall law (u+ = y+) in the viscous sublayer (y+ < 10) and log law away from the wall (y+> 30). Radial position of zero shear stress and maximum velocity were found to be slightly different (2%). Root mean square values of velocity fluctuations velocity, Reynolds stresses, vorticity, and turbulent kinetic energy budget were also analyzed.

An Experimental Investigation of Turbulent Drag Reduction in Concentric Annulus Using Particle Image Velocimetry Technique

2013 ◽  
Author(s):  
Fabio Ernesto Rodriguez Corredor ◽  
Majid Bizhani ◽  
Ergun Kuru
Keyword(s):  
Particle Image Velocimetry ◽  
Turbulent Flow ◽  
Drag Reduction ◽  
Particle Image ◽  
Reynolds Shear Stress ◽  
Polymer Concentration ◽  
Mean Flow ◽  
Flow Loop ◽  
Mean Velocity ◽  
Image Velocimetry

Polymer drag reduction is investigated using the Particle Image Velocimetry (PIV) technique in fully developed turbulent flow through a horizontal flow loop with concentric annular geometry (inner to outer pipe radius ratio = 0.4). The polymer used was a commercially available partially hydrolyzed polyacrylamide (PHPA). The polymer concentration was varied from 0.07 to 0.12% V/V. The drag reduction is enhanced by increasing polymer concentration until the concentration reaches an optimum value. After that, the drag reduction is decreased with the increasing polymer concentration. Optimum concentration value of PHPA was found to be around 0.1% V/V. Experiments were conducted at solvent Reynolds numbers of 38700, 46700 and 56400. The percent drag reduction was found to be increasing with the increasing Reynolds number. The study was also focused on analyzing the mean flow and turbulence statistics for fully-turbulent flow using the velocity measurements acquired by PIV. Axial mean velocity profile was found to be following the universal wall law close to the wall (i.e., y+ <10), but it deviated from log law results with an increased slope in the logarithmic zone (i.e., y+ >30). In all cases of polymer application, the viscous sublayer (i.e., y+ <10) thickness was found to be higher than that of the water flow. Reynolds shear stress in the core flow region was found to be decreasing with the increase in polymer concentration.

scholarly journals Particle image velocimetry measurement of turbulent wake past circular cylinder at Reynolds numbers from 2.5·103 to 1.5·104

2021 ◽  
Vol 345 ◽  
pp. 00030
Author(s):  
Ondřej Sterly
Keyword(s):  
Particle Image Velocimetry ◽  
Circular Cylinder ◽  
Particle Image ◽  
Transverse Velocity ◽  
Reynolds Numbers ◽  
Particle Image Velocimetry Technique ◽  
Recirculation Bubble ◽  
Image Velocimetry ◽  
Ensemble Statistics ◽  
Vorticity Component

A canonical case of air flow past a circular cylinder is studied by using Particle Image Velocimetry technique. This contribution focus to the ensemble statistics (first and second moment) of the stream-wise and transverse velocity component as well as to the in-plane vorticity component. Although the range of explored Reynolds numbers is narrow, we observe a significant shortening of recirculation bubble within this range.

Analysis of local velocity gradients in rapid mixer using particle image velocimetry technique

2002 ◽  
Vol 2 (5-6) ◽  
pp. 47-55
Author(s):  
N.-S. Park ◽  
H. Park
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Velocity Fields ◽  
Local Velocity ◽  
Mixing Condition ◽  
Particle Image Velocimetry Technique ◽  
Velocity Gradients ◽  
Image Velocimetry ◽  
Current Design ◽  
G Value

Recognizing the significance of factual velocity fields in a rapid mixer, this study focuses on analyzing local velocity gradients in various mixer geometries with particle image velocimetry (PIV) and comparing the results of the analysis with the conventional G-value, for reviewing the roles of G-value in the current design and operation practices. The results of this study clearly show that many arguments and doubts are possible about the scientific correctness of G-value, and its current use. This is because the G-value attempts to represent the turbulent and complicated factual velocity field in a jar. Also, the results suggest that it is still a good index for representing some aspects of mixing condition, at least, mixing intensity. However, it cannot represent the distribution of velocity gradients in a jar, which is an important factor for mixing. This study as a result suggests developing another index for representing the distribution to be used with the G-value.

A particle image velocimetry study on the pulsatile flow characteristics in straight tubes with an asymmetric bulge

2000 ◽  
Vol 214 (5) ◽  
pp. 655-671 ◽  
Author(s):  
S C M Yu ◽  
J B Zhao
Keyword(s):  
Particle Image Velocimetry ◽  
Steady Flow ◽  
Pulsatile Flow ◽  
Flow Condition ◽  
Particle Image ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Flow Conditions ◽  
Image Velocimetry

Flow characteristics in straight tubes with an asymmetric bulge have been investigated using particle image velocimetry (PIV) over a range of Reynolds numbers from 600 to 1200 and at a Womersley number of 22. A mixture of glycerine and water (approximately 40:60 by volume) was used as the working fluid. The study was carried out because of their relevance in some aspects of physiological flows, such as arterial flow through a sidewall aneurysm. Results for both steady and pulsatile flow conditions were obtained. It was found that at a steady flow condition, a weak recirculating vortex formed inside the bulge. The recirculation became stronger at higher Reynolds numbers but weaker at larger bulge sizes. The centre of the vortex was located close to the distal neck. At pulsatile flow conditions, the vortex appeared and disappeared at different phases of the cycle, and the sequence was only punctuated by strong forward flow behaviour (near the peak flow condition). In particular, strong flow interactions between the parent tube and the bulge were observed during the deceleration phase. Stents and springs were used to dampen the flow movement inside the bulge. It was found that the recirculation vortex could be eliminated completely in steady flow conditions using both devices. However, under pulsatile flow conditions, flow velocities inside the bulge could not be suppressed completely by both devices, but could be reduced by more than 80 per cent.

scholarly journals A New Particle Image Velocimetry Technique for Turbomachinery Applications

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Sayantan Bhattacharya ◽  
Reid A. Berdanier ◽  
Pavlos P. Vlachos ◽  
Nicole L. Key
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Laser Sheet ◽  
Measurement Techniques ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Particle Image Velocimetry Technique ◽  
Optical Access ◽  
Tip Leakage ◽  
Image Velocimetry

Nonintrusive measurement techniques such as particle image velocimetry (PIV) are growing in both capability and utility for turbomachinery applications. However, the restrictive optical access afforded by multistage research compressors typically requires the use of a periscope probe to introduce the laser sheet for measurements in a rotor passage. This paper demonstrates the capability to perform three-dimensional PIV in a multistage compressor without the need for intrusive optical probes and requiring only line-of-sight optical access. The results collected from the embedded second stage of a three-stage axial compressor highlight the rotor tip leakage flow, and PIV measurements are qualitatively compared with high-frequency response piezoresistive pressure measurements to assess the tip leakage flow identification.

Measurement of Velocity Profiles of Laminar to Turbulent Water Flows in a Tube Using Particle Image Velocimetry

2004 ◽  
Author(s):  
Meredith R. Martin
Keyword(s):  
Reynolds Number ◽  
Particle Image Velocimetry ◽  
Particle Image ◽  
Glass Tube ◽  
Reynolds Numbers ◽  
Velocity Profiles ◽  
Reynolds Number Flow ◽  
Image Velocimetry ◽  
Dye Visualization ◽  
Number Flow

The transition from laminar to turbulent in-tube flow is studied in this paper. Water flow in a glass tube with an inside diameter of 21.7 mm was investigated by two methods. First, a dye visualization test using a setup similar to the 1883 experiment of Osborne Reynolds was conducted. For the dye visualization, Reynolds numbers ranging from approximately 1000 to 3500 were tested and the transition from laminar to turbulent flow was observed between Reynolds numbers of 2500 and 3500. For the second method, a particle image velocimetry (PIV) system was used to measure the velocity profiles of flow in the same glass tube at Reynolds numbers ranging from approximately 500 to 9000. The resulting velocity profiles were compared to theoretical laminar profiles and empirical turbulent power-law profiles. Good agreement was found between the lower Reynolds number flow and the laminar profile, and between the higher Reynolds number flow and turbulent power-law profile. In between the flow appeared to be in a transition region and deviated some between the two profiles.

Abstract 14952: Volumetric Echocardiographic Particle Image Velocimetry (V-Echo-PIV)

Circulation ◽  
2014 ◽  
Vol 130 (suppl_2) ◽  
Author(s):  
Ahmad Falahatpisheh ◽  
Arash Kheradvar
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Contrast Echocardiography ◽  
Ultrasound Contrast Agent ◽  
Three Dimensions ◽  
Small Scale ◽  
High Temporal Resolution ◽  
Two Dimensional ◽  
Particle Image Velocimetry Technique ◽  
Image Velocimetry

Introduction: The two-dimensional (2D) echocardiographic particle image velocimetry technique that was introduced in 2010 received much attention in clinical cardiology. Cardiac flow visualization based on contrast echocardiography results in images with high temporal resolution that are obtainable at relatively low cost. This makes it an ideal diagnostic and follow-up tool for routine clinical use. However, cardiac flow in a cardiac cycle is multidirectional with a tendency to spin in three dimensions rather than two-dimensional curl. Here, for the first time, we introduce a volumetric echocardiographic particle image velocimetry technique that robustly acquires the flow in three spatial dimensions and in time: Volumetric Echocardiographic Particle Image Velocimetry (V-Echo-PIV). Methods: V-Echo-PIV technique utilizes matrix array 3D ultrasound probes to capture the flow seeded with an ultrasound contrast agent (Definity). For this feasibility study, we used a pulse duplicator with a silicone ventricular sac along with bioprosthetic heart valves at the inlet and outlet. GE Vivid E9 system with an Active Matrix 4D Volume Phased Array probe at 30 Hz was used to capture the flow data (Figure 1). Results: The 3D particle field was obtained with excellent spatial resolution without significant noise (Figure 1). 3D velocity field was successfully captured for multiple cardiac cycles. Flow features are shown in Figure 2 where the velocity vectors in two selected slices and some streamlines in 3D space are depicted. Conclusions: We report successful completion of the feasibility studies for volumetric echocardiographic PIV in an LV phantom. The small-scale features of flow in the LV phantom were revealed by this technique. Validation and human studies are currently in progress.

PIV Investigation of an Open Channel Flow Over a Forward Facing Step

2007 ◽  
Author(s):  
M. K. Shah ◽  
M. F. Tachie
Keyword(s):  
Open Channel ◽  
Particle Image ◽  
Open Channel Flow ◽  
Reynolds Stresses ◽  
Velocity Measurements ◽  
Particle Image Velocimetry Technique ◽  
Mean Velocity ◽  
Freestream Velocity ◽  
Image Velocimetry ◽  
Forward Facing Step

The characteristics of an open channel turbulent flow over a forward facing step (FFS) are investigated in the present study. Two step heights, h = 6 and 9 mm, at Reynolds number, Reh, (based on the approach freestream velocity, U0, and step height, h) of 1900 and 2800 respectively were studied. Particle image velocimetry technique (PIV) was used to obtain detailed velocity measurements upstream of the FFS, in the reattachment region (x/h = 0, 1, 2) and in the redevelopment region (x/h = 4, 10, 15 and 50). The boundary layer integral parameters, mean velocity profiles and Reynolds stresses obtained in the reattachment and redevelopment region are used to document some of the salient features of the flow.

Stereoscopic Particle Image Velocimetry of Native Ovine Mitral Valves in a Pulsatile Left Heart Simulator

2012 ◽  
Author(s):  
Jean-Pierre Rabbah ◽  
Neelakantan Saikrishnan ◽  
Ajit P. Yoganathan
Keyword(s):  
Particle Image Velocimetry ◽  
Mitral Valve ◽  
Computational Models ◽  
Particle Image ◽  
Numerical Models ◽  
Stereoscopic Particle Image Velocimetry ◽  
Patient Specific ◽  
Flow Loop ◽  
Mitral Valves ◽  
Image Velocimetry

Patient specific mitral valve computational models are being actively developed to facilitate surgical planning. These numerical models increasingly employ more realistic geometries, kinematics, and mechanical properties, which in turn requires rigorous experimental validation [1]. However, to date, native mitral flow dynamics have not been accurately and comprehensively characterized. In this study, we used Stereoscopic Particle Image Velocimetry (SPIV) to characterize the ventricular flow field proximal to a native mitral valve in a pulsatile experimental flow loop.

Sign in / Sign up

Export Citation Format

Share Document