Operational Space Prescribed Tracking Performance and Compliance in Flexible Joint Robots

2015 ◽  
Vol 137 (7) ◽  
Author(s):  
Abdelrahem Atawnih ◽  
Zoe Doulgeri ◽  
George A. Rovithakis
Keyword(s):  
Degrees Of Freedom ◽  
Position Tracking ◽  
Admittance Control ◽  
Flexible Joint ◽  
Flexible Joint Robots ◽  
Operational Space ◽  
Control Scheme ◽  
Simulation Results ◽  
Flexible Joint Manipulator ◽  
Three Degrees Of Freedom

In this work, an admittance control scheme is proposed utilizing a highly robust prescribed performance position tracking controller for flexible joint robots which is designed at the operational space. The proposed control scheme achieves the desired impedance to the external contact force as well as superior position tracking in free motion without any robot model knowledge, as opposed to the torque based impedance controllers. Comparative simulation results on a three degrees-of-freedom (3DOF) flexible joint manipulator, illustrate the efficiency of the approach.

scholarly journals Extended and Unscented Kalman Filtering Applied to a Flexible-Joint Robot with Jerk Estimation

2010 ◽  
Vol 2010 ◽  
pp. 1-14 ◽  
Author(s):  
Mohammad Ali Badamchizadeh ◽  
Iraj Hassanzadeh ◽  
Mehdi Abedinpour Fallah
Keyword(s):  
Initial Conditions ◽  
Covariance Matrices ◽  
Flexible Joints ◽  
Velocity Measurements ◽  
Lagrange Equations ◽  
Robust Nonlinear Control ◽  
Flexible Joint ◽  
Flexible Joint Robots ◽  
Simulation Results

Robust nonlinear control of flexible-joint robots requires that the link position, velocity, acceleration, and jerk be available. In this paper, we derive the dynamic model of a nonlinear flexible-joint robot based on the governing Euler-Lagrange equations and propose extended and unscented Kalman filters to estimate the link acceleration and jerk from position and velocity measurements. Both observers are designed for the same model and run with the same covariance matrices under the same initial conditions. A five-bar linkage robot with revolute flexible joints is considered as a case study. Simulation results verify the effectiveness of the proposed filters.

scholarly journals Strategies of traversing obstacles and the simulation for a forestry chassis

2018 ◽  
Vol 15 (3) ◽  
pp. 172988141877390 ◽  
Author(s):  
Yue Zhu ◽  
Jiangming Kan ◽  
Wenbin Li ◽  
Feng Kang
Keyword(s):  
Multibody Dynamics ◽  
Inclination Angle ◽  
Degrees Of Freedom ◽  
Ride Comfort ◽  
Hydraulic Cylinder ◽  
Single Side ◽  
Simulation Results ◽  
Maximum Inclination ◽  
Three Degrees Of Freedom ◽  
Small Inclination

As to the complicated terrain in forest, forestry chassis with an articulated body with three degrees of freedom and installed luffing wheel-legs (FC-3DOF&LW) is a novel chassis that can surmount obstacles. In addition, the rear frame of FC-3DOF&LW is regarded as the platform to carry equipment. Small inclination angle for rear frame contributes to stability and ride comfort. This article describes the strategy of traversing obstacles and simulation for FC-3DOF&LW that drives in forest terrain. First, key structures of FC-3DOF&LW are briefly introduced, which include articulated structure with three degrees of freedom and luffing wheel-leg. Based on the sketch of luffing wheel-leg, the movement range of luffing wheel-leg is obtained by hydraulic cylinder operation. Second, the strategy of crossing obstacles that are simplified three models of terrain is presented, and the simulation for surmounting obstacles is constructed in multibody dynamics software. The simulation results demonstrate that the inclination angle of rear frame is 18° when slope is 30°. A maximum 12° decrease of inclination angle for rear frame can be acquired when luffing wheel-legs are applied. For traversing obstacles with both sides, the maximum inclination angle of rear frame is about 1.2° and is only 3° for traversing obstacles with single side.

Actuator Array Dynamics Incorporating Actuator Inertia

2013 ◽  
Author(s):  
Mark D. Bedillion
Keyword(s):  
Degrees Of Freedom ◽  
Friction Model ◽  
Object Motion ◽  
Prior Work ◽  
Control Laws ◽  
Distributed Manipulation ◽  
Actuator Arrays ◽  
Simulation Results ◽  
Two Degree Of Freedom ◽  
Three Degrees Of Freedom

Actuator arrays are planar distributed manipulation systems that use multiple two degree-of-freedom actuators to manipulate objects with three degrees of freedom (x, y, and θ). Prior work has discussed actuator array dynamics while neglecting the inertia of the actuators; this paper extends prior work to the case of non-negligible actuator inertia. The dynamics are presented using a standard friction model incorporating stiction. Simulation results are presented that show object motion under previously derived control laws.

Region-Reaching Control of a Flexible-Joint Manipulator

2020 ◽  
Vol 142 (11) ◽  
Author(s):  
J. W. Yu ◽  
X. H. Zhang ◽  
J. C. Ji ◽  
J. Y. Tian ◽  
J. Zhou
Keyword(s):  
Control Problem ◽  
Tracking Control ◽  
Control Algorithm ◽  
Objective Functions ◽  
Flexible Joint ◽  
Point Tracking ◽  
Control Scheme ◽  
Lyapunov Stability Analysis ◽  
Flexible Joint Manipulator ◽  
Theoretical Results

Abstract This paper addresses the region-reaching control problem for a flexible-joint robotic manipulator which is formulated by Lagrangian dynamics. An adaptive control scheme is proposed for the manipulator system having two constrained regions which are constructed by selecting appropriate objective functions. The two joints of the flexible-joint manipulator can be, respectively, confined in different regions, and this gives more flexibility than the traditional fixed-point tracking control. By performing a straightforward Lyapunov stability analysis, a simple control algorithm is established to provide a solution for the region-reaching control problem. Finally, numerical simulations are given to validate the theoretical results.

The Kinematics Model and Simulation of a Subminiature Based on Marine Ranching

2014 ◽  
Vol 909 ◽  
pp. 135-140
Author(s):  
Jie Jiang Shao ◽  
Feng Peng Wei ◽  
Lan Zhen
Keyword(s):  
Degrees Of Freedom ◽  
Complex Environment ◽  
Kinematics Model ◽  
Model And Simulation ◽  
Simulation Results ◽  
Freedom Movement ◽  
Three Degrees Of Freedom

A subminiature submersible has been designed on the basis of the condition of the marine ranching, especially the shape of the submersible in view of the complex environment of marine ranching. Its mainly designed from three major movements, namely advance, ups-downs and yawing movement; it can complete three degrees of freedom movement. At the same time a force analysishas beengiven. Thetransfer functions have been deduced, and the simulation structure has been designed according to its kinematics model. According to the simulation results, the feasibility of the kinematics model was verified.

Sign in / Sign up

Export Citation Format

Share Document