Damage Evolution in Lead Free Solder Joints in Isothermal Fatigue

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
Awni Qasaimeh ◽  
Sa’d Hamasha ◽  
Younis Jaradat ◽  
Peter Borgesen
Keyword(s):  
Crack Initiation ◽  
Mechanical Response ◽  
Solder Joints ◽  
Fatigue Testing ◽  
Hysteresis Loops ◽  
Damage Function ◽  
Lead Free ◽  
Lead Free Solder ◽  
Sac305 Solder ◽  
Free Solder

The extrapolation and generalization of accelerated test results for lead free solder joints require the identification of a damage function that can be counted on to apply beyond the region of the test. Individual ball grid array (BGA) scale Sn3Ag0.5Cu (SAC305) solder joints were subjected to isothermal shear fatigue testing at room temperature and 65 °C. The resulting mechanical response degradation and crack behavior, including strain hardening, crack initiation, and propagation, were correlated with the inelastic work and effective stiffness derived from load–displacement hysteresis loops. Crack initiation was found to scale with the accumulated work, independently of cycling amplitude and strain rate. The subsequent damage rate varied slightly with amplitude.

Effect of Aging on the Properties of Intermetallic Layers in SAC+Bi Solder Joints

2021 ◽  
Author(s):  
Mohammad Ashraful Haq ◽  
Mohd Aminul Hoque ◽  
Jeffrey C. Suhling ◽  
Pradeep Lall
Keyword(s):  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Aging Condition ◽  
Sac305 Solder ◽  
The Poor ◽  
Free Solder ◽  
Lead Free Solders ◽  
Overall Reliability ◽  
Intermetallic Layers

Abstract A major problem faced by electronic packaging industries is the poor reliability of lead free solder joints. One of the most common methods utilized to tackle this problem is by doping the alloy with other elements, especially bismuth. Researches have shown Bismuth doped solder joints to mostly fail near the Intermetallic (IMC) layer rather than the bulk of the solder joint as commonly observed in traditional SAC305 solder joints. An understanding of the properties of this IMC layer would thus provide better solutions on improving the reliability of bismuth doped solder joints. In this study, the authors have used three different lead free solders doped with 1%, 2% and 3% bismuth. Joints of these alloys were created on copper substrates. The joints were then polished to clearly expose the IMC layers. These joints were then aged at 125 °C for 0, 1, 2, 5 and 10 days. For each aging condition, the elastic modulus and the hardness of the IMC layers were evaluated using a nanoindenter. The IMC layer thickness and the chemical composition of the IMC layers were also determined for each alloy at every aging condition using Scanning Electron Microscopy (SEM) and EDS. The results from this study will give a better idea on how the percentage of bismuth content in lead free solder affects the IMC layer properties and the overall reliability of the solder joints.

Investigation of the Effects of High Temperature Aging on Mechanical Behavior and Microstructural Changes in Lead Free Solders

2019 ◽  
Author(s):  
Jing Wu ◽  
Mohammad S. Alam ◽  
Jeffrey C. Suhling ◽  
Pradeep Lall
Keyword(s):  
Ostwald Ripening ◽  
Solder Joints ◽  
Particle Diameter ◽  
Lead Free ◽  
Average Particle ◽  
Lead Free Solder ◽  
Aging Effects ◽  
Sac305 Solder ◽  
Free Solder

Abstract Aging effects are common in lead free solder joints within electronic assemblies that are exposed to isothermal environments for extended periods. Such exposures lead to evolution of the solder microstructure, which results in changes in the mechanical properties and creep behavior of the solder joints. In our recent investigations, we have been utilizing Scanning Electron Microscopy (SEM) to better understand aging induced degradations. The microstructural evolutions were observed in SAC305 and SAC_Q (SAC+Bi) alloys exposed to isothermal conditions at T = 125 °C for several different regions from several different joints. The microstructures in several fixed regions of interest were recorded after predetermined time intervals of aging, which were 1 hour (up to 24 hours) and 10 hours (up to 150 hours) for the short term aging samples; and 250 hours (up to 2500 hours) for the long term aging samples. Using the recorded images and imaging processing software, the area and diameter of each IMC particle was tracked during the aging process. As expected, the quantitative analysis of the evolving SAC_Q microstructure showed that the particles coalesced during aging leading to a decrease in the number of particles. This caused an increase in the average diameter of the particles of slightly more than 100% for long term aging of 2500 hours. For SAC305, the average particle diameter was found to increase at three times the rate (increase of 200% after 2500 hours of aging). Thus, coarsening of IMC particles was greatly mitigated in the SAC_Q alloy relative to that observed in SAC305. Immediately after reflow solidification, Bismuth rich phases were present in the SAC_Q joints. During aging at T = 125 °C, the bismuth was observed to quickly go into solution both within the beta-Sn dendrites and in the intermetallic rich regions between dendrites. This resulted in solid solution strengthening of the lead free solder. It was also found that the aging-induced presence of bismuth in solution within the beta-Sn matrix provided an increased resistance to the Ostwald ripening diffusion process that coarsens the Ag3Sn IMC particles. The combination of these two effects in the SAC+Bi alloy lead to greatly improved resistance to aging induced effects relative to the SAC305 solder alloy. Finally, we have compared the time dependent evolution of microstructure with the degradation in strength during aging for of the two solder alloys, and good correlations were observed.

Study of Lead Free Solder Joints Subjected to Isothermal Mechanical Shear Cycling

2020 ◽  
Author(s):  
Mohd Aminul Hoque ◽  
Mohammad Ashraful Haq ◽  
Jeffrey C. Suhling ◽  
Pradeep Lall
Keyword(s):  
Printed Circuit Boards ◽  
Solder Joints ◽  
Polarized Light ◽  
Lead Free ◽  
Lead Free Solder ◽  
Circuit Boards ◽  
Sac305 Solder ◽  
Mechanical Cycling ◽  
Before And After ◽  
Free Solder

Abstract Electronic packages are usually subjected to varying temperature conditions, thus subjecting the package to thermal cyclic loadings. As the different components of the package are made up of materials of different Coefficients of Thermal Expansion (CTE), the thermal cyclic loading brings about fluctuating shear stress to arise within the package, ultimately leading to its failure. It has been seen in previous literature that the recrystallization assisted cracking is a major factor that leads to the failure of solder joints when subjected to thermomechanical cycles. In this study, the authors have tried to determine whether the mechanical shear cycling of aged and non-aged samples of SAC305 lead free solder joints undergo a recrystallization phase before its ultimate failure. Arrays (3 × 3) of SAC305 solder joints of roughly 750μm in diameter were reflowed in between two FR-4 printed circuit boards to create a sandwiched structural sample. The samples were then polished to expose the solder joints. A polarized light microscope was utilized to capture the images of the joints before and after the mechanical cycling and analyzed to observe any changes in the microstructure in the form of recrystallization of the tin grains.

Void Formation and Their Effect on Reliability of Lead-Free Solder Joints on MID and PCB Substrates

2017 ◽  
Vol 66 (4) ◽  
pp. 1229-1237 ◽  
Author(s):  
P. Wild ◽  
T. Grozinger ◽  
D. Lorenz ◽  
A. Zimmermann
Keyword(s):  
Solder Joints ◽  
Void Formation ◽  
Lead Free ◽  
Lead Free Solder ◽  
Free Solder

Quantitative Evaluation of Voids in Lead Free Solder Joints

2015 ◽  
Vol 772 ◽  
pp. 284-289 ◽  
Author(s):  
Sabuj Mallik ◽  
Jude Njoku ◽  
Gabriel Takyi
Keyword(s):  
Solder Bump ◽  
Solder Joints ◽  
Void Formation ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
X Ray ◽  
Size And Shape ◽  
Solder Bumps ◽  
Free Solder

Voiding in solder joints poses a serious reliability concern for electronic products. The aim of this research was to quantify the void formation in lead-free solder joints through X-ray inspections. Experiments were designed to investigate how void formation is affected by solder bump size and shape, differences in reflow time and temperature, and differences in solder paste formulation. Four different lead-free solder paste samples were used to produce solder bumps on a number of test boards, using surface mount reflow soldering process. Using an advanced X-ray inspection system void percentages were measured for three different size and shape solder bumps. Results indicate that the voiding in solder joint is strongly influenced by solder bump size and shape, with voids found to have increased when bump size decreased. A longer soaking period during reflow stage has negatively affectedsolder voids. Voiding was also accelerated with smaller solder particles in solder paste.

Sign in / Sign up

Export Citation Format

Share Document