Near Wall Modeling for Trailing Edge Slot Film Cooling

2014 ◽  
Vol 137 (2) ◽  
Author(s):  
Julia Ling ◽  
Riccardo Rossi ◽  
John K. Eaton
Keyword(s):  
Boundary Layer ◽  
Film Cooling ◽  
Scale Model ◽  
Wall Region ◽  
Turbulent Diffusivity ◽  
Trailing Edge ◽  
Reynolds Analogy ◽  
Rans Models ◽  
Slot Film Cooling ◽  
Near Wall

Trailing edge slot film cooling is a widely used active cooling scheme for turbine blade trailing edges. Current Reynolds-Averaged Navier–Stokes (RANS) models are known to significantly overpredict the adiabatic effectiveness of these configurations. It is shown that this overprediction is due in part to the breakdown of the Reynolds analogy between turbulent shear stress and scalar transport in the near wall region. By examining previously reported direct numerical simulation (DNS) results for a wall-mounted cube in cross flow, it is seen that in a flow with a significantly perturbed outer boundary layer, the turbulent diffusivity is not as strongly damped as the turbulent viscosity in the viscous sublayer and buffer layer of the boundary layer. By removing the Van Driest damping function from the length scale model for the turbulent diffusivity, more accurate turbulent diffusivity predictions are possible. This near wall correction is applied to trailing edge slot film cooling flows and it is demonstrated that the predictive accuracy of the RANS models is significantly enhanced. Detailed comparisons between RANS results and experimental datasets for 15 different cases demonstrate that this correction gives significant improvement to the accuracy of the RANS predictions across a broad range of trailing edge slot film cooling configurations.

The Effects of Adverse Pressure Gradients on Momentum and Thermal Structures in Transitional Boundary Layers: Part 2—Fluctuation Quantities

1996 ◽  
Vol 118 (4) ◽  
pp. 728-736 ◽  
Author(s):  
S. P. Mislevy ◽  
T. Wang
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Transition Region ◽  
Boundary Layers ◽  
Reynolds Shear Stress ◽  
Turbulent Shear ◽  
Wall Region ◽  
Pressure Gradients ◽  
Baseline Case ◽  
Near Wall

The effects of adverse pressure gradients on the thermal and momentum characteristics of a heated transitional boundary layer were investigated with free-stream turbulence ranging from 0.3 to 0.6 percent. Boundary layer measurements were conducted for two constant-K cases, K1 = −0.51 × 10−6 and K2 = −1.05 × 10−6. The fluctuation quantities, u′, ν′, t′, the Reynolds shear stress (uν), and the Reynolds heat fluxes (νt and ut) were measured. In general, u′/U∞, ν′/U∞, and νt have higher values across the boundary layer for the adverse pressure-gradient cases than they do for the baseline case (K = 0). The development of ν′ for the adverse pressure gradients was more actively involved than that of the baseline. In the early transition region, the Reynolds shear stress distribution for the K2 case showed a near-wall region of high-turbulent shear generated at Y+ = 7. At stations farther downstream, this near-wall shear reduced in magnitude, while a second region of high-turbulent shear developed at Y+ = 70. For the baseline case, however, the maximum turbulent shear in the transition region was generated at Y+ = 70, and no near-wall high-shear region was seen. Stronger adverse pressure gradients appear to produce more uniform and higher t′ in the near-wall region (Y+ < 20) in both transitional and turbulent boundary layers. The instantaneous velocity signals did not show any clear turbulent/nonturbulent demarcations in the transition region. Increasingly stronger adverse pressure gradients seemed to produce large non turbulent unsteadiness (or instability waves) at a similar magnitude as the turbulent fluctuations such that the production of turbulent spots was obscured. The turbulent spots could not be identified visually or through conventional conditional-sampling schemes. In addition, the streamwise evolution of eddy viscosity, turbulent thermal diffusivity, and Prt, are also presented.

scholarly journals Active control of multiscale features in wall-bounded turbulence

2019 ◽  
Vol 36 (1) ◽  
pp. 12-21 ◽  
Author(s):  
Xiaotong Cui ◽  
Nan Jiang ◽  
Xiaobo Zheng ◽  
Zhanqi Tang
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Turbulent Energy ◽  
Streamwise Velocity ◽  
Discrete Wavelet ◽  
Wall Region ◽  
Mean Velocity ◽  
Pzt Actuator ◽  
The Impact ◽  
Near Wall

Abstract This study experimentally investigates the impact of a single piezoelectric (PZT) actuator on a turbulent boundary layer from a statistical viewpoint. The working conditions of the actuator include a range of frequencies and amplitudes. The streamwise velocity signals in the turbulent boundary layer flow are measured downstream of the actuator using a hot-wire anemometer. The mean velocity profiles and other basic parameters are reported. Spectra results obtained by discrete wavelet decomposition indicate that the PZT vibration primarily influences the near-wall region. The turbulent intensities at different scales suggest that the actuator redistributes the near-wall turbulent energy. The skewness and flatness distributions show that the actuator effectively alters the sweep events and reduces intermittency at smaller scales. Moreover, under the impact of the PZT actuator, the symmetry of vibration scales’ velocity signals is promoted and the structural composition appears in an orderly manner. Probability distribution function results indicate that perturbation causes the fluctuations in vibration scales and smaller scales with high intensity and low intermittency. Based on the flatness factor, the bursting process is also detected. The vibrations reduce the relative intensities of the burst events, indicating that the streamwise vortices in the buffer layer experience direct interference due to the PZT control.

Development of the turbulent near wake of a tapered thick flat plate

1988 ◽  
Vol 189 ◽  
pp. 135-163 ◽  
Author(s):  
A. Haji-Haidari ◽  
C. R. Smith
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flat Plate ◽  
Wall Region ◽  
Turbulence Structure ◽  
Near Wake ◽  
Growth Region ◽  
Trailing Edge ◽  
Centreline Velocity ◽  
Hot Film

The velocity field and turbulence structure in the near wake of a thick flat plate with a tapered trailing-edge geometry are examined using both hydrogen-bubble flow visualization and hot-film anemometry measurements. Tests were conducted for Re1 = 8.5 × 105 in the region 0 < x+ < 6400 behind the trailing edge. The probe and visualization results indicate a similarity between both (i) velocity and turbulence structure variations wih x+ in the near wake, and (ii) the corresponding changes in similar flow characteristics with y+ within a turbulent boundary layer. In particular, visualization data in the vicinity of the wake centreline reveal the existence of strong streamwise flow structures in the region close (x+ < 270) to the trailing edge. The streamwise orientation of the observed structures diminishes as x+ increases. From hot-film measurements, two separate regions along the wake centreline can be distinguished: (i) a linear growth region which extends over 0 < x+ < 100, wherein the centreline velocity varies linearly with x+; and (ii) a logarithmic growth region for x+ > 270, wherein the centreline velocity varies as log x+. The similarity in behaviour between these regions and the comparable wall region of a turbulent boundary layer suggests the existence of a common functionality. This similarity is demonstrated by a simple linear relationship of the form y+ = Kx+, which is shown to approximately collapse the velocity behaviour both across a turbulent boundary layer and along the wake centreline to a unified set of empirical relationships.

Influence of large-scale motions on the frictional drag in a turbulent boundary layer

2017 ◽  
Vol 829 ◽  
pp. 751-779 ◽  
Author(s):  
Jinyul Hwang ◽  
Hyung Jin Sung
Keyword(s):  
Boundary Layer ◽  
Skin Friction ◽  
Large Scale ◽  
Wall Region ◽  
Local Skin ◽  
Velocity Fluctuations ◽  
Vortical Structures ◽  
Change Of Scale ◽  
Local Skin Friction ◽  
Near Wall

Direct numerical simulation data of a turbulent boundary layer ($Re_{\unicode[STIX]{x1D70F}}=1000$) were used to investigate the large-scale influences on the vortical structures that contribute to the local skin friction. The amplitudes of the streamwise and wall-normal swirling strengths ($\unicode[STIX]{x1D706}_{x}$and$\unicode[STIX]{x1D706}_{y}$) were conditionally sampled by measuring the large-scale streamwise velocity fluctuations ($u_{l}$). In the near-wall region, the amplitudes of$\unicode[STIX]{x1D706}_{x}$and$\unicode[STIX]{x1D706}_{y}$decreased under negative$u_{l}$rather than under positive$u_{l}$. This behaviour arose from the spanwise motions within the footprints of the large-scale low-speed ($u_{l}<0$) and high-speed structures ($u_{l}>0$). The intense spanwise motions under the footprint of positive$u_{l}$noticeably strengthened the small-scale spanwise velocity fluctuations ($w_{s}$) below the centre of the near-wall vortical structures as compared to$w_{s}$within the footprint of negative$u_{l}$. The streamwise and wall-normal components were attenuated or amplified around the modulated vortical motions, which in turn led to the dependence of the swirling strength on the$u_{l}$event. We quantified the contribution of the modulated vortical motions$\langle -w\unicode[STIX]{x1D714}_{y}\rangle$, which were related to a change-of-scale effect due to the vortex-stretching force, to the local skin friction. In the near-wall region, intense values of$\langle -w\unicode[STIX]{x1D714}_{y}\rangle$were observed for positive$u_{l}$. By contrast, these values were low for negative$u_{l}$, in connection with the amplification of$w_{s}$and$\unicode[STIX]{x1D706}_{y}$by the strong spanwise motions of the positive$u_{l}$. The resultant skin friction induced by the amplified vortical motions within$u_{l}^{+}>2$was responsible for 15 % of the total skin friction generated by the change-of-scale effect. Finally, we applied this analysis to a drag-reduced flow and found that the amplified vortical motions within the footprint of positive$u_{l}$were markedly diminished, which ultimately contributed to the total drag reduction.

Experimental observation of hairpin auto-generation events in a turbulent boundary layer

2016 ◽  
Vol 795 ◽  
pp. 611-633 ◽  
Author(s):  
Y. Jodai ◽  
G. E. Elsinga
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Shear Layer ◽  
Transition Process ◽  
Wall Region ◽  
Generation Model ◽  
Streamwise Vortices ◽  
Hairpin Vortices ◽  
Time Resolved ◽  
Near Wall

Time-resolved tomographic particle image velocimetry experiments show that new hairpin vortices are generated within a fully developed and unperturbed turbulent boundary layer. The measurements are taken at a Reynolds number based on the momentum thickness of 2038, and cover the near-wall region below $y^{+}=140$, where $y^{+}$ is the wall-normal distance in wall units. Instantaneous visualizations of the flow reveal near-wall low-speed streaks with associated quasi-streamwise vortices, retrograde inverted arch vortices, hairpin vortices and hairpin packets. The hairpin heads are observed as close to the wall as $y^{+}=30$. Examples of hairpin packet evolution reveal the development of new hairpin vortices, which are created upstream and close to the wall in a manner consistent with the auto-generation model (Zhou et al., J. Fluid Mech., vol. 387, 1999, pp. 353–396). The development of the new hairpin appears to be initiated by an approaching sweep event, which perturbs the shear layer associated with the initial packet. The shear layer rolls up, thereby forming the new hairpin head. The head subsequently connects to existing streamwise vortices and develops into a hairpin. The time scale associated with the hairpin auto-generation is 20–30 wall units of time. This demonstrates that hairpins can be created over short distances within a developed turbulent boundary layer, implying that they are not simply remnants of the laminar-to-turbulent transition process far upstream.

Modeling Interfacial Interactions and Turbulence in the Near-Wall Region of a Vertical Bubbly Boundary Layer

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
Jamel Chahed ◽  
Lucien Masbernat
Keyword(s):  
Boundary Layer ◽  
Void Fraction ◽  
Fluid Model ◽  
Second Order ◽  
Turbulence Closure ◽  
Wall Region ◽  
Turbulence Structure ◽  
Two Fluid Model ◽  
Two Fluid ◽  
Near Wall

Abstract A two-fluid model with second-order turbulence closure is used for the simulation of a turbulent bubbly boundary layer. The turbulence model is based on the decomposition of the Reynolds stress tensor in the liquid phase into two parts: a turbulent part and a pseudo-turbulent part. The reduction in second-order turbulence closure in the near-wall region is interpreted according to a modified wall logarithmic law. Numerical simulations of bubbly boundary layer developing on a vertical flat plate were performed in order to analyze the bubbles effect on the liquid turbulence structure and to evaluate the respective roles of turbulence and of interfacial forces in the near-wall distribution of the void fraction. The two-fluid model with the second-order turbulence closure succeeds in reproducing the diminution of the turbulent intensity observed in the near-wall region of bubbly boundary layer and the increase in turbulence outside the boundary layer. The analysis of the interfacial force in the near-wall zone has led to the development of relatively simple formulation of the lift-wall force in the logarithmic zone that depends on dimensionless distances to the wall. After appropriate adjustment, this formulation makes it possible to reproduce the shape of the near-wall void fraction peaking observed in bubbly boundary layer experiments.

POD Investigation of Near-Wall Turbulent Structures

2002 ◽  
Author(s):  
Gaetano Maria Di Cicca ◽  
Angelo Iollo ◽  
Pier Giorgio Spazzini ◽  
Gaetano Iuso ◽  
Michele Onorato
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Particle Image ◽  
Digital Particle Image Velocimetry ◽  
Orthogonal Decomposition ◽  
Wall Region ◽  
Turbulent Structures ◽  
Image Velocimetry ◽  
Proper Orthogonal ◽  
Near Wall

Experimental data of a turbulent boundary layer developing over a flat plate, obtained by Digital Particle Image Velocimetry (DPIV) technique, are analyzed making use of proper orthogonal decomposition (POD). Different POD definitions have been used in order to check their ability in educing the various structures dominating the near wall region. Results show a specific sensitivity depending on the POD definition adopted.

Sign in / Sign up

Export Citation Format

Share Document