Investigation of Residual Stress Development During Swage Autofrettage, Using Finite Element Analysis

2014 ◽  
Vol 136 (2) ◽  
Author(s):  
Michael C. Gibson ◽  
Amer Hameed ◽  
John G. Hetherington
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Axial Stress ◽  
Slope Angle ◽  
Subsequent Development ◽  
Element Model ◽  
Pressure Vessels ◽  
Element Analysis ◽  
Reverse Yielding

Swaging is one method of autofrettage, a means of prestressing high-pressure vessels to increase their fatigue lives and load bearing capacity. Swaging achieves the required deformation through physical interference between an oversized mandrel and the bore diameter of the tube, as it is pushed through the tube. A finite element model of the swaging process was developed, in ansys, and systematically refined, to investigate the mechanism of deformation and subsequent development of residual stresses. A parametric study was undertaken, of various properties such as mandrel slope angle, parallel section length, and friction coefficient. It is observed that the axial stress plays a crucial role in the determination of the residual hoop stress and reverse yielding. The model, and results obtained from it, provides a means of understanding the swaging process and how it responds to different parameters. This understanding, coupled with future improvements to the model, potentially allows the swaging process to be refined, in terms of residual stresses development and mandrel driving force.

Investigation of Residual Stress Development During Swage Autofrettage, Using Finite Element Analysis

2009 ◽  
Author(s):  
Michael C. Gibson ◽  
Amer Hameed ◽  
John G. Hetherington
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Axial Stress ◽  
Slope Angle ◽  
Subsequent Development ◽  
Element Model ◽  
Pressure Vessels ◽  
Element Analysis ◽  
Reverse Yielding

Swaging is one method of autofrettage, a means of pre-stressing high-pressure vessels to increase their fatigue lives and load bearing capacity. Swaging achieves the required deformation through physical interference between an oversized mandrel and the bore diameter of the tube, as it is pushed through the tube. A Finite Element model of the swaging process was developed, in ANSYS, and systematically refined, to investigate the mechanism of deformation and subsequent development of residual stresses. A parametric study was undertaken, of various properties such as mandrel slope angle, parallel section length and friction coefficient. It is observed that the axial stress plays a crucial role in the determination of the residual hoop stress and reverse yielding. The model, and results obtained from it, provides a means of understanding the swaging process and how it responds to different parameters. This understanding, coupled with future improvements to the model, potentially allows the swaging process to be refined, in terms of residual stresses development and mandrel driving force.

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

2000 ◽  
Vol 123 (1) ◽  
pp. 150-154
Author(s):  
John H. Underwood ◽  
Michael J. Glennon
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Fatigue Life ◽  
Yield Strength ◽  
Residual Stresses ◽  
Solid Mechanics ◽  
Element Model ◽  
Pressure Vessels ◽  
Material Strength ◽  
Element Analysis

Laboratory fatigue life results are summarized from several test series of high-strength steel cannon breech closure assemblies pressurized by rapid application of hydraulic oil. The tests were performed to determine safe fatigue lives of high-pressure components at the breech end of the cannon and breech assembly. Careful reanalysis of the fatigue life tests provides data for stress and fatigue life models for breech components, over the following ranges of key parameters: 380–745 MPa cyclic internal pressure; 100–160 mm bore diameter cannon pressure vessels; 1040–1170 MPa yield strength A723 steel; no residual stress, shot peen residual stress, overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid mechanics analysis. Shot peen and overload residual stresses are modeled by superposing typical or calculated residual stress distributions on the applied stresses. Overload residual stresses are obtained directly from the finite element model of the breech, with the breech overload applied to the model in the same way as with actual components. Modeling of the fatigue life of the components is based on the fatigue intensity factor concept of Underwood and Parker, a fracture mechanics description of life that accounts for residual stresses, material yield strength and initial defect size. The fatigue life model describes six test conditions in a stress versus life plot with an R2 correlation of 0.94, and shows significantly lower correlation when known variations in yield strength, stress concentration factor, or residual stress are not included in the model input, thus demonstrating the model sensitivity to these variables.

Maximum Stress at Intersecting Bores of Pressurized Blocks

1994 ◽  
Author(s):  
Ajay Garg
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Tensile Stress ◽  
Element Model ◽  
Maximum Tensile Stress ◽  
Pressure Vessels ◽  
Experimental Results ◽  
Empirical Methods ◽  
Element Analysis ◽  
Matched Design

Abstract In high pressure applications, rectangular blocks of steel are used instead of cylinders as pressure vessels. Bores are drilled in these blocks for fluid flow. Intersecting bores with axes normal to each other and of almost equal diameters, produce stresses which can be many times higher than the internal pressure. Experimental results for the magnitude of maximum tensile stress along the intersection contour were available. A parametric finite element model simulated the experimental set up, followed by correlation between finite element analysis and experimental results. Finally, empirical methods are applied to generate models for the maximum tensile stress σ11 at cross bores of open and close ended blocks. Results from finite element analysis and empirical methods are further matched. Design optimization of cross bores is discussed.

Finite Element Analysis of Residual Stresses in Threaded End Closures

1991 ◽  
Vol 113 (3) ◽  
pp. 398-401 ◽  
Author(s):  
A. Chaaban ◽  
U. Muzzo
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Bauschinger Effect ◽  
High Stress ◽  
Empirical Method ◽  
Pressure Vessels ◽  
Element Analysis ◽  
High Stress Concentration ◽  
Proof Testing ◽  
Pressure Cycle

Due to the high stress concentration at the root of the first active thread in threaded end closures of high pressure vessels, yielding may occur in this region during the application of the first pressure cycle or proof testing. This overstraining introduces residual stresses that influence the fatigue performance of the vessel. This paper presents a parametric analysis of threaded end closures using elastic and elasto-plastic finite element solutions. The results are used to discuss the influence of these residuals on the estimated fatigue life when the vessel is subjected to repeated internal pressure. A simple empirical method to allow for the Bauschinger effect of the material is also proposed.

An assessment of the Sachs method for measuring residual stresses in cold worked fastener holes

1998 ◽  
Vol 33 (4) ◽  
pp. 263-274 ◽  
Author(s):  
D J Smith ◽  
C G C Poussard ◽  
M J Pavier
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Cold Working ◽  
Element Model ◽  
Fe Model ◽  
Working Process ◽  
Element Analysis ◽  
Near Surface ◽  
Cold Worked ◽  
Good Agreement

Measurements of residual stresses in 6 mm thick aluminium alloy 2024 plates containing 4 per cent cold worked fastener are made using the Sachs method. The measurements are made on discs extracted from the plates. The measured tangential residual stress distribution adjacent to the hole edge are found to be affected by the disc diameter. The measured residual stresses are also in good agreement with averaged through-thickness predictions of residual stresses from an axisymmetric finite element (FE) model of the cold working process. A finite element analysis is also conducted to simulate disc extraction and then the Sachs method. The measured FE residual stresses from the Sachs simulation are found to be in good agreement with the averaged through-thickness predicted residual stresses. The Sachs simulation was not able to reproduce the detailed near-surface residual stresses found from the finite element model of the cold working process.

Finite Element Analysis of Flange Joint With Single and Twin Gaskets Under External Bending Load

2015 ◽  
Author(s):  
N. Rino Nelson ◽  
N. Siva Prasad ◽  
A. S. Sekhar
Keyword(s):  
Finite Element ◽  
Work Performance ◽  
Elevated Temperatures ◽  
Bending Moment ◽  
Element Model ◽  
Pressure Vessels ◽  
Flange Joint ◽  
Element Analysis ◽  
Bending Load ◽  
Gasket Material

Gasketed flange joint is a vital component in pressure vessels and piping systems. Flange joint is usually subjected to bending load due to expansion, wind load, self-weight, etc. Most of the flange design methods use equivalent pressure to include the effect of external bending loads. It becomes complex when the joint is subjected to bending load at elevated temperatures, due to the nonlinear behavior of gasket material. In the present work, performance of the flange joint has been studied under external bending load at elevated temperatures. A 3D finite element model is developed, considering the nonlinearities in the joint due to gasket material and contact between its members along with their temperature dependent material properties. The performance of the joint under different bolt preloads, internal fluid pressures and temperatures is studied. Flange joint with two gaskets (twin gasketed joint) placed beside each other radially, is also analyzed under external bending moment. The maximum allowable bending moments at different internal temperatures, for single and twin gasketed joints with spiral wound gasket are arrived.

Probabilistic finite element analysis of residual stress formation in shrink-fit ceramic/steel gun barrels

2002 ◽  
Vol 216 (4) ◽  
pp. 219-231
Author(s):  
M Grujicic ◽  
J R DeLong ◽  
W S DeRossett
Keyword(s):  
Residual Stress ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Residual Stresses ◽  
Axial Stress ◽  
Sampling Technique ◽  
Cumulative Distribution ◽  
Element Analysis ◽  
Gun Barrel ◽  
Ceramic Lining

The development of residual stresses in a hybrid α-SiC lining/CrMoV steel jacket gun barrel during shrink fitting of the jacket over the lining is studied using a probabilistic finite element analysis. Particular attention is given to understanding the development of the axial compressive stress in the ceramic lining, since this stress (if sufficiently high) can prevent lining failure caused by formation and growth of circumferential cracks near the barrel ends. To quantify the effect of variability in various design, material and process parameters on the magnitude and the distribution of the axial residual stress, a probabilistic structural analysis approach, known as the advanced mean value (AMV) method, is used, enabling determination of the cumulative distribution function for failure of the lining. The results obtained are validated using the adaptive importance sampling (AIS) method, an efficient direct statistical sampling technique. Lastly, the corresponding sensitivity factors which quantify the effect of variability in each parameter on the magnitude of axial residual stresses in the ceramic lining are computed. The results indicate that the loss of the compressive axial stress in the lining near the barrel ends is affected to the greatest extent by the magnitude of the friction coefficient at the lining/barrel interface.

Finite element analysis of the phase transformation effect in residual stresses generated by quenching in notched steel cylinders

2005 ◽  
Vol 40 (2) ◽  
pp. 151-160 ◽  
Author(s):  
E P Silva ◽  
P M C L Pacheco ◽  
M. A Savi
Keyword(s):  
Finite Element ◽  
Phase Transformation ◽  
Residual Stresses ◽  
Induction Hardening ◽  
Martensite Phase ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Thermomechanical Behaviour ◽  
Quenching Process

The determination of residual stresses is an important task in the analysis of the quenching process. Nevertheless, because of the complexity of the phenomenon, many simplifications are usually adopted in the prediction of these stresses for engineering purposes. One of these simplifications is the effect of phase transformation. Many studies analyse residual stresses generated by the quenching process considering a thermoelastoplastic approach, neglecting phase transformation. The present study analyses the effect of austenite-martensite phase transformation during quenching in the determination of residual stresses, comparing two different models: complete (thermoelastoplastic model with austenite-martensite phase transformation) and without phase transformation (thermoelastoplastic model without phase transformation). The finite element method is employed for spatial discretization together with a constitutive model that represents the thermomechanical behaviour of the quenching process. Progressive induction hardening of steel cylinders with semicircular notches is of concern. Numerical simulations show situations where great discrepancies are introduced in the predicted residual stresses if phase transformation is neglected.

Numerical and Experimental Study of Elastic Interaction in Bolted Flange Joints

2017 ◽  
Vol 139 (2) ◽  
Author(s):  
Linbo Zhu ◽  
Abdel-Hakim Bouzid ◽  
Jun Hong
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Experimental Tests ◽  
Elastic Interaction ◽  
Element Model ◽  
Interaction Coefficient ◽  
Pressure Vessels ◽  
Nonlinear Finite Element ◽  
Element Analysis ◽  
Bolted Flange

Bolted flange joints are widely used to connect pressure vessels and piping equipment together and facilitate their disassembly. Initial tightening of their bolts is a delicate operation because it is extremely difficult to achieve the target load and uniformity due to elastic interaction. The risk of failure due to leakage and fatigue under service loading is consequently increased. This paper presents a study on the effect of elastic interaction that is present during the tightening of bolted flange joints using three-dimensional nonlinear finite-element modeling and experimentation. The nonlinear nonelastic behavior of the gasket is taken into account in the numerical simulation. The scatter in bolt preload produced during the tightening sequence is evaluated. Based on the elastic interaction coefficient method, the initial target tightening load in each bolt for every pass is determined by using the nonlinear finite-element model to obtain a uniform preload after the final tightening pass. The validity of the finite-element analysis (FEA) is supported by experimental tests conducted on a NPS 4 class 900 weld neck bolted flange joints using fiber and flexible graphite gaskets. This study provides guidance and enhances the safety and reliability of bolted flange joints by minimizing bolt load scatter due to elastic interaction.

scholarly journals Numerical Evaluation of Advanced Laser Control Strategies Influence on Residual Stresses for Laser Powder Bed Fusion Systems

2020 ◽  
Vol 9 (4) ◽  
pp. 435-445
Author(s):  
Massimo Carraturo ◽  
Brandon Lane ◽  
Ho Yeung ◽  
Stefan Kollmannsberger ◽  
Alessandro Reali ◽  
...  
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Laser Power ◽  
High Speed ◽  
Control Strategies ◽  
Element Model ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Element Analysis ◽  
Powder Bed

AbstractProcess-dependent residual stresses are one of the main burdens to a widespread adoption of laser powder bed fusion technology in industry. Residual stresses are directly influenced by process parameters, such as laser path, laser power, and speed. In this work, the influence of various scan speed and laser power control strategies on residual stresses is investigated. A set of nine different laser scan patterns is printed by means of a selective laser melting process on a bare plate of nickel superalloy 625 (IN625). A finite element model is experimentally validated comparing the simulated melt pool areas with high-speed thermal camera in situ measurements. Finite element analysis is then used to evaluate residual stresses for the nine different laser scan control strategies, in order to identify the strategy which minimizes the residual stress magnitude. Numerical results show that a constant power density scan strategy appears the most effective to reduce residual stresses in the considered domain.

Sign in / Sign up

Export Citation Format

Share Document