Fully Coupled Three-Dimensional Dynamic Response of a Tension-Leg Platform Floating Wind Turbine in Waves and Wind

2014 ◽  
Vol 136 (2) ◽  
Author(s):  
G. K. V. Ramachandran ◽  
H. Bredmose ◽  
J. N. Sørensen ◽  
J. J. Jensen
Keyword(s):  
Wind Turbine ◽  
Three Dimensional ◽  
Geographical Location ◽  
Climatic Conditions ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Total System ◽  
Wave Loads ◽  
Tension Leg Platform ◽  
Aerodynamic Loads

A dynamic model for a tension-leg platform (TLP) floating offshore wind turbine is proposed. The model includes three-dimensional wind and wave loads and the associated structural response. The total system is formulated using 17 degrees of freedom (DOF), 6 for the platform motions and 11 for the wind turbine. Three-dimensional hydrodynamic loads have been formulated using a frequency- and direction-dependent spectrum. While wave loads are computed from the wave kinematics using Morison's equation, the aerodynamic loads are modeled by means of unsteady blade-element-momentum (BEM) theory, including Glauert correction for high values of the axial induction factor, dynamic stall, dynamic wake, and dynamic yaw. The aerodynamic model takes into account the wind shear and turbulence effects. For a representative geographical location, platform responses are obtained for a set of wind and wave climatic conditions. The platform responses show an influence from the aerodynamic loads, most clearly through quasi-steady mean surge and pitch responses associated with the mean wind. Further, the aerodynamic loads show an influence from the platform motion through a fluctuating rotor load contribution, which is a consequence of the wave-induced rotor dynamics. Loads and coupled responses are predicted for a set of load cases with different wave headings. Further, an advanced aero-elastic code, Flex5, is extended for the TLP wind turbine configuration and the response comparison with the simpler model shows a generally good agreement, except for the yaw motion. This deviation is found to be a result of the missing lateral tower flexibility in the simpler model.

Fully Coupled Three-Dimensional Dynamic Response of a TLP Floating Wind Turbine in Waves and Wind

2012 ◽  
Author(s):  
G. K. V. Ramachandran ◽  
H. Bredmose ◽  
J. N. Sørensen ◽  
J. J. Jensen
Keyword(s):  
Wind Turbine ◽  
Dynamic Model ◽  
Three Dimensional ◽  
Geographic Location ◽  
Climatic Conditions ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Total System ◽  
Wave Loads ◽  
Aerodynamic Loads

A dynamic model for a tension-leg platform (TLP) floating offshore wind turbine is proposed. The model includes three-dimensional wind and wave loads and the associated structural response. The total system is formulated using 17 degrees of freedom (DOF), 6 for the platform motions and 11 for the wind turbine. Three-dimensional hydrodynamic loads have been formulated using a frequency- and direction-dependent spectrum. While wave loads are computed from the wave kinematics using Morison’s equation, aerodynamic loads are modelled by means of unsteady Blade-Element-Momentum (BEM) theory, including Glauert correction for high values of axial induction factor, dynamic stall, dynamic wake and dynamic yaw. The aerodynamic model takes into account the wind shear and turbulence effects. For a representative geographic location, platform responses are obtained for a set of wind and wave climatic conditions. The platform responses show an influence from the aerodynamic loads, most clearly through a quasi-steady mean surge and pitch response associated with the mean wind. Further, the aerodynamic loads show an influence from the platform motion through more fluctuating rotor loads, which is a consequence of the wave-induced rotor dynamics. In the absence of a controller scheme for the wind turbine, the rotor torque fluctuates considerably, which induces a growing roll response especially when the wind turbine is operated nearly at the rated wind speed. This can be eliminated either by appropriately adjusting the controller so as to regulate the torque or by optimizing the floater or tendon dimensions, thereby limiting the roll motion. Loads and coupled responses are predicted for a set of load cases with different wave headings. Based on the results, critical load cases are identified and discussed. As a next step (which is not presented here), the dynamic model for the substructure is therefore being coupled to an advanced aero-elastic code Flex5, Øye (1996), which has a higher number of DOFs and a controller module.

scholarly journals Study of Floating Wind Turbine with Modified Tension Leg Platform Placed in Regular Waves

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 703 ◽  
Author(s):  
Juhun Song ◽  
Hee-Chang Lim
Keyword(s):  
Wind Turbine ◽  
Real Data ◽  
Offshore Wind ◽  
Scale Model ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Tension Leg Platform ◽  
Mooring Lines ◽  
Floating Wind Turbine ◽  
Wave Conditions

In this study, the typical ocean environment was simulated with the aim to investigate the dynamic response under various environmental conditions of a Tension Leg Platform (TLP) type floating offshore wind turbine system. By applying Froude scaling, a scale model with a scale of 1:200 was designed and model experiments were carried out in a lab-scale wave flume that generated regular periodic waves by means of a piston-type wave generator while a wave absorber dissipated wave energy on the other side of the channel. The model was designed and manufactured based on the standard prototype of the National Renewable Energy Laboratory (NREL) 5 MW offshore wind turbine. In the first half of the study, the motion and structural responses for operational wave conditions of the North Sea near Scotland were considered to investigate the performance of a traditional TLP floating wind turbine compared with that of a newly designed TLP with added mooring lines. The new mooring lines were attached with the objective of increasing the horizontal stiffness of the system and thereby reducing the dominant motion of the TLP platform (i.e., the surge motion). The results of surge translational motions were obtained both in the frequency domain, using the response amplitude operator (RAO), and in the time domain, using the omega arithmetic method for the relative velocity. The results obtained show that our suggested concept improves the stability of the platform and reduces the overall motion of the system in all degrees-of-freedom. Moreover, the modified design was verified to enable operation in extreme wave conditions based on real data for a 100-year return period of the Northern Sea of California. The loads applied by the waves on the structure were also measured experimentally using modified Morison equation—the formula most frequently used to estimate wave-induced forces on offshore floating structures. The corresponding results obtained show that the wave loads applied on the new design TLP had less amplitude than the initial model and confirmed the significant contribution of the mooring lines in improving the performance of the system.

Coupled Dynamic Analysis of a Tension Leg Platform Floating Offshore Wind Turbine

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Teng Wang ◽  
Hui Jin ◽  
Xiaoni Wu
Keyword(s):  
Dynamic Analysis ◽  
Wind Turbine ◽  
Offshore Wind ◽  
Wind Loads ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Tension Leg Platform ◽  
Floating Offshore Wind Turbine ◽  
Turbulent Wind ◽  
Coupled Dynamic Analysis

The dynamic response of a tension leg platform (TLP) floating offshore wind turbine (FOWT) was analyzed with considering the aero-hydro characteristic of the whole floating wind turbine system including the wind turbine, TLP platform, and tethers. The “aero-hydro” coupled dynamic analysis was conducted in ansys-aqwa with a dynamic link library (DLL) calculating the aerodynamics loading at every steptime based on the blade element momentum theory. Results from the coupled dynamic analysis of TLP FOWT under the condition of turbulent wind and regular wave show that the wind loads influence mainly the low-frequency response of the TLP FOWT. The wind loads have a large impact on the offsets of the TLP away from the initial position while the wave loads influence mainly the fluctuation amplitude of the TLP FOWT. The average TLP pitch response under the wind load is significantly larger due to the large wind-induced heeling moment on the wind turbine. In addition, the tension of tethers at the upwind end is greater than that at the downwind end. The wind loads could reduce effectively the average tension of the tethers, and the tension of tethers is significantly affected by the pitch motion. Results from the coupled dynamic analysis of TLP FOWT under the condition of turbulent wind and irregular wave show that the surge and pitch of TLP result in an obvious increase of thrust of the turbine and the amplitude of torque fluctuation, more attention should be paid to the pitch and surge motion of TLP FOWT.

scholarly journals Numerical Validation of Floating Offshore Wind Turbine Scaled Rotors for Surge Motion

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2578 ◽  
Author(s):  
Krishnamoorthi Sivalingam ◽  
Steven Martin ◽  
Abdulqadir Singapore Wala
Keyword(s):  
Wind Turbine ◽  
Turbine Rotor ◽  
Power Converter ◽  
Experimental Results ◽  
Offshore Wind ◽  
Speed Ratio ◽  
Offshore Wind Turbine ◽  
Floating Offshore Wind Turbine ◽  
Aerodynamic Loads ◽  
Unsteady Aerodynamic

Aerodynamic performance of a floating offshore wind turbine (FOWT) is significantly influenced by platform surging motions. Accurate prediction of the unsteady aerodynamic loads is imperative for determining the fatigue life, ultimate loads on key components such as FOWT rotor blades, gearbox and power converter. The current study examines the predictions of numerical codes by comparing with unsteady experimental results of a scaled floating wind turbine rotor. The influence of platform surge amplitude together with the tip speed ratio on the unsteady aerodynamic loading has been simulated through unsteady CFD. It is shown that the unsteady aerodynamic loads of FOWT are highly sensitive to the changes in frequency and amplitude of the platform motion. Also, the surging motion significantly influences the windmill operating state due to strong flow interaction between the rotating blades and generated blade-tip vortices. Almost in all frequencies and amplitudes, CFD, LR-BEM and LR-uBEM predictions of mean thrust shows a good correlation with experimental results.

scholarly journals The Effect of the Second-Order Wave Loads on Drift Motion of a Semi-Submersible Floating Offshore Wind Turbine

2020 ◽  
Vol 8 (11) ◽  
pp. 859
Author(s):  
Thanh-Dam Pham ◽  
Hyunkyoung Shin
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Second Order ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Hydrodynamic Loads ◽  
Drift Motion ◽  
Offshore Wind Turbines ◽  
Floating Offshore Wind Turbines

Floating offshore wind turbines (FOWTs) have been installed in Europe and Japan with relatively modern technology. The installation of floating wind farms in deep water is recommended because the wind speed is stronger and more stable. The design of the FOWT must ensure it is able to withstand complex environmental conditions including wind, wave, current, and performance of the wind turbine. It needs simulation tools with fully integrated hydrodynamic-servo-elastic modeling capabilities for the floating offshore wind turbines. Most of the numerical simulation approaches consider only first-order hydrodynamic loads; however, the second-order hydrodynamic loads have an effect on a floating platform which is moored by a catenary mooring system. At the difference-frequencies of the incident wave components, the drift motion of a FOWT system is able to have large oscillation around its natural frequency. This paper presents the effects of second-order wave loads to the drift motion of a semi-submersible type. This work also aimed to validate the hydrodynamic model of Ulsan University (UOU) in-house codes through numerical simulations and model tests. The NREL FAST code was used for the fully coupled simulation, and in-house codes of UOU generates hydrodynamic coefficients as the input for the FAST code. The model test was performed in the water tank of UOU.

scholarly journals Spoke Dimension on the Motion Performance of a Floating Wind Turbine with Tension-Leg Platform

2016 ◽  
Vol 2016 ◽  
pp. 1-16
Author(s):  
H. F. Wang ◽  
Y. H. Fan
Keyword(s):  
Wind Turbine ◽  
Good Choice ◽  
Offshore Wind ◽  
Experimental Result ◽  
Offshore Wind Turbine ◽  
Tension Leg Platform ◽  
Irregular Wave ◽  
Wind Turbine System ◽  
Floating Offshore Wind Turbines ◽  
Tower Structure

The tension-leg platform (TLP) supporting structure is a good choice for floating offshore wind turbines because TLP has superior motion dynamics. This study investigates the effects of TLP spoke dimensions on the motion of a floating offshore wind turbine system (FOWT). Spoke dimension and offshore floating TLP were subjected to irregular wave and wind excitation to evaluate the motion of the FOWT. This research has been divided into two parts: (1) Five models were designed based on different spoke dimensions, and aerohydroservo-elastic coupled analyses were conducted on the models using the finite element method. (2) Considering the coupled effects of the dynamic response of a top wind turbine, a supporting-tower structure, a mooring system, and two models on a reduced scale of 1 : 80 were constructed and experimentally tested under different conditions. Numerical and experimental results demonstrate that the spoke dimensions have a significant effect on the motion of FOWT and the experimental result that spoke dimension can reduce surge platform movement to improve turbine performance.

Key Contributors to Lifetime Accumulated Fatigue Damage in an Offshore Wind Turbine Support Structure

2017 ◽  
Author(s):  
Emil Smilden ◽  
Erin E. Bachynski ◽  
Asgeir J. Sørensen
Keyword(s):  
Wind Turbine ◽  
Fatigue Damage ◽  
Control Strategies ◽  
Time Domain Analysis ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Support Structure ◽  
Wear And Tear ◽  
Collateral Effects

A simulation study is performed to identify the key contributors to lifetime accumulated fatigue damage in the support-structure of a 10 MW offshore wind turbine placed on a monopile foundation in 30 m water depth. The relative contributions to fatigue damage from wind loads, wave loads, and wind/wave misalignment are investigated through time-domain analysis combined with long-term variations in environmental conditions. Results show that wave loads are the dominating cause of fatigue damage in the support structure, and that environmental condtions associated with misalignment angle > 45° are insignificant with regard to the lifetime accumulated fatigue damage. Further, the results are used to investigate the potential of event-based use of control strategies developed to reduce fatigue loads through active load mitigation. Investigations show that a large reduction in lifetime accumulated fatigue damage is possible, enabling load mitigation only in certain situations, thus limiting collateral effects such as increased power fluctuations, and wear and tear of pitch actuators and drive-train components.

Experimental Study on the Wave Loads on Monopile and Jacket Type Support of Offshore Wind Turbines

2018 ◽  
Author(s):  
Jing Zhang ◽  
Qin Liu ◽  
Xing Hua Shi ◽  
C. Guedes Soares
Keyword(s):  
Experimental Study ◽  
Wind Turbine ◽  
Nonlinear Wave ◽  
Wave Force ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Wave Forces ◽  
Wave Loads ◽  
Morison Equation ◽  
Offshore Wind Turbines

As the offshore fixed wind turbine developed, more ones will be installed in the sea field with the depth 15–50 meters. Wave force will be one of the main forces that dominate the design of the wind turbine base, which is calculated using the Morison equation traditionally. This method can predict the wave forces for the small cylinders if the drag and inertia coefficients are obtained accurately. This paper will give a series scaled tests of monopile and jacket type base of the offshore wind turbine in tank to study the nonlinear wave loads.

Sign in / Sign up

Export Citation Format

Share Document