Predictions of Unsteady Interactions Between Closely Coupled High Pressure- and Low Pressure-Turbines With Co- and Counterrotation

2013 ◽  
Vol 135 (6) ◽  
Author(s):  
T. J. Praisner ◽  
E. A. Grover ◽  
R. Mocanu ◽  
R. J. Jurek ◽  
R. E. Gacek
Keyword(s):  
High Pressure ◽  
Surface Pressure ◽  
Analytical Study ◽  
Low Pressure ◽  
Tangential Load ◽  
Low Pressure Turbine ◽  
Unsteady Aerodynamic ◽  
Complex Interactions ◽  
Unsteady Surface Pressure ◽  
Turbine Vane

Here, we report on an analytical study of the unsteady aerodynamic interactions of a closely coupled, corotating, high- and low-pressure turbine configuration. The effort was focused on the prediction of unsteady surface pressures imparted on the first blade of the low-pressure turbine (LPT). As a first step, a baseline three-row time-accurate prediction was carried out for the first three rows of the low-pressure turbine (vane-blade-vane). In contrast to the three-row results, a four-row analysis, which included the blade of the high-pressure turbine, revealed that the temporally varying tangential load on the LPT blade was increased in amplitude by a factor of five compared to the three-row case with a shift in primary unsteady energy to unexpected frequencies. In the four-row analysis, a region of unusually high unsteadiness near the tip of the LPT blade was also characterized by an increase in the amplitude of the fluctuating surface pressure by a factor of nearly seven, again, with unexpected attendant frequencies. A model is presented which explains the unexpected frequencies realized in the four-row results and allows the predetermination of these frequencies without the use of computational fluid dynamics. In an effort to better understand the complex interactions between the high- and low-pressure turbines, the first vane of the low-pressure turbine was redesigned, and the remaining airfoils were reoriented, to establish a counterrotating turbine configuration. While substantial reductions in unsteady surface-pressure amplitudes were realized near the tip of the LPT blade with the switch to counterrotation, the amplitude of the temporally varying tangential load on the blade remained notably higher than that from the three-row analysis. The precise physical cause for the high levels of local unsteadiness near the tip of the first LPT blade in the corotating configuration remains unclear.

Predictions of Unsteady Interactions Between Closely Coupled HP and LP Turbines With Co- and Counter-Rotation

2010 ◽  
Author(s):  
T. J. Praisner ◽  
E. Grover ◽  
R. Mocanu ◽  
R. Jurek ◽  
R. Gacek
Keyword(s):  
Surface Pressure ◽  
Analytical Study ◽  
Low Pressure ◽  
Tangential Load ◽  
Low Pressure Turbine ◽  
Unsteady Aerodynamic ◽  
Complex Interactions ◽  
Counter Rotation ◽  
Unsteady Surface Pressure ◽  
Turbine Vane

Here we report on an analytical study of the unsteady aerodynamic interactions of a closely coupled, co-rotating, high- and low-pressure turbine configuration. The effort was focused on the prediction of unsteady surface pressures imparted on the first blade of the low-pressure turbine (LPT). As a first step, a baseline three-row time-accurate prediction was carried out for the first three rows of the low-pressure turbine (vane-blade-vane). In contrast to the three-row results, a four-row analysis, which included the blade of the high-pressure turbine, revealed that the temporally varying tangential load on the LPT blade was increased in amplitude by a factor of five compared to the three-row case with a shift in primary unsteady energy to unexpected frequencies. In the four-row analysis, a region of unusually high unsteadiness near the tip of the LPT blade was also characterized by an increase in the amplitude of the fluctuating surface pressure by a factor of nearly seven, again, with unexpected attendant frequencies. A model is presented which explains the unexpected frequencies realized in the four-row results and allows the redetermination of these frequencies without the use of CFD. In an effort to better understand the complex interactions between the high- and low-pressure turbines, the first vane of the low-pressure turbine was redesigned, and the remaining airfoils were reoriented, to establish a counter-rotating turbine configuration. While substantial reductions in unsteady surface-pressure amplitudes were realized near the tip of the LPT blade with the switch to counter rotation, the amplitude of the temporally varying tangential load on the blade remained notably higher than that from the three-low analysis. The precise physical cause for the high levels of local unsteadiness near the tip of the first LPT blade in the co-rotating configuration remains unclear.

scholarly journals Unsteady Interaction Between a Transonic Turbine Stage and Downstream Components

2004 ◽  
Vol 10 (6) ◽  
pp. 495-506 ◽  
Author(s):  
Roger L. Davis ◽  
Jixian Yao ◽  
John P. Clark ◽  
Gary Stetson ◽  
Juan J. Alonso ◽  
...  
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Surface Pressure ◽  
Low Pressure ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Unsteady Pressure ◽  
Low Pressure Turbine ◽  
Unsteady Surface Pressure ◽  
Turbine Vane

Results from a numerical simulation of the unsteady flow through one quarter of the circumference of a transonic high-pressure turbine stage, transition duct, and low-pressure turbine first vane are presented and compared with experimental data. Analysis of the unsteady pressure field resulting from the simulation shows the effects of not only the rotor/stator interaction of the high-pressure turbine stage but also new details of the interaction between the blade and the downstream transition duct and low-pressure turbine vane. Blade trailing edge shocks propagate downstream, strike, and reflect off of the transition duct hub and/or downstream vane leading to high unsteady pressure on these downstreamcomponents. The reflection of these shocks from the downstream components back into the blade itself has also been found to increase the level of unsteady pressure fluctuations on the uncovered portion of the blade suction surface. In addition, the blade tip vortex has been found to have a moderately strong interaction with the downstream vane even with the considerable axial spacing between the two blade-rows. Fourier decomposition of the unsteady surface pressure of the blade and downstream low-pressure turbine vane shows the magnitude of the various frequencies contributing to the unsteady loads. Detailed comparisons between the computed unsteady surface pressure spectrum and the experimental data are shown along with a discussion of the various interaction mechanisms between the blade, transition duct, and downstream vane. These comparisons show-overall good agreement between the simulation and experimental data and identify areas where further improvements in modeling are needed.

scholarly journals Unsteady Interaction Between a Transonic Turbine Stage and Downstream Components

2002 ◽  
Author(s):  
Roger L. Davis ◽  
Jixian Yao ◽  
John P. Clark ◽  
Gary Stetson ◽  
Juan J. Alonso ◽  
...  
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Surface Pressure ◽  
Low Pressure ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Unsteady Pressure ◽  
Low Pressure Turbine ◽  
Unsteady Surface Pressure ◽  
Turbine Vane

Results from a numerical simulation of the unsteady flow through one quarter of the circumference of a transonic high-pressure turbine stage, transition duct, and low-pressure turbine first vane are presented and compared with experimental data. Analysis of the unsteady pressure field resulting from the simulation shows the effects of not only the rotor/stator interaction of the high-pressure turbine stage but also new details of the interaction between the blade and the downstream transition duct and low-pressure turbine vane. Blade trailing edge shocks propagate downstream, strike, and reflect off of the transition duct hub and/or downstream vane leading to high unsteady pressure on these downstream components. The reflection of these shocks from the downstream components back into the blade itself has also been found to increase the level of unsteady pressure fluctuations on the uncovered portion of the blade suction surface. In addition, the blade tip vortex has been found to have a moderately strong interaction with the downstream vane even with the considerable axial spacing between the two blade-rows. Fourier decomposition of the unsteady surface pressure of the blade and downstream low-pressure turbine vane shows the magnitude of the various frequencies contributing to the unsteady loads. Detailed comparisons between the computed unsteady surface pressure spectrum and the experimental data are shown along with a discussion of the various interaction mechanisms between the blade, transition duct, and downstream vane. These comparisons show overall good agreement between the simulation and experimental data and identify areas where further improvements in modeling are needed.

Experimental Investigation of Vane Clocking in a One and 1/2 Stage High Pressure Turbine

2004 ◽  
Author(s):  
Charles W. Haldeman ◽  
Michael G. Dunn ◽  
John W. Barter ◽  
Brian R. Green ◽  
Robert F. Bergholz
Keyword(s):  
High Pressure ◽  
Low Pressure ◽  
Test Facility ◽  
Maximum Efficiency ◽  
High Pressure Turbine ◽  
Data Set ◽  
Time Resolved ◽  
Low Pressure Turbine ◽  
Turbine Vane ◽  
Vane Clocking

Aerodynamic measurements were acquired on a modern single-stage, transonic, high-pressure turbine with the adjacent low-pressure turbine vane row (a typical civilian one and one-half stage turbine rig) to observe the effects of low-pressure turbine vane clocking on overall turbine performance. The turbine rig (loosely referred to in this paper as the stage) was operated at design corrected conditions using the Ohio State University Gas Turbine Laboratory Turbine Test Facility (TTF). The research program utilized uncooled hardware in which all three airfoils were heavily instrumented at multiple spans to develop a full clocking dataset. The low-pressure turbine vane row (LPTV) was clocked relative to the high-pressure turbine vane row (HPTV). Various methods were used to evaluate the influence of clocking on the aeroperformance (efficiency) and the aerodynamics (pressure loading) of the LPTV, including time-resolved and time-averaged measurements. A change in overall efficiency of approximately 2–3% due to clocking effects is demonstrated and could be observed using a variety of independent methods. Maximum efficiency is obtained when the time-average surface pressures are highest on the LPTV and the time-resolved surface pressure (both in the time domain and frequency domain) show the least amount of variation. The overall effect is obtained by integrating over the entire airfoil, as the three-dimensional effects on the LPTV surface are significant. This experimental data set validates several computational research efforts that suggested wake migration is the primary reason for the perceived effectiveness of vane clocking. The suggestion that wake migration is the dominate mechanism in generating the clocking effect is also consistent with anecdotal evidence that fully cooled engine rigs do not see a great deal of clocking effect. This is consistent since the additional disturbances induced by the cooling flows and/or the combustor make it extremely difficult to find an alignment for the LPTV given the strong 3D nature of modern high-pressure turbine flows.

Experimental Investigation of Vane Clocking in a One and One-Half Stage High Pressure Turbine

2004 ◽  
Vol 127 (3) ◽  
pp. 512-521 ◽  
Author(s):  
Charles W. Haldeman ◽  
Michael Dunn ◽  
John W. Barter ◽  
Brian R. Green ◽  
Robert F. Bergholz
Keyword(s):  
High Pressure ◽  
Low Pressure ◽  
Test Facility ◽  
Maximum Efficiency ◽  
High Pressure Turbine ◽  
Data Set ◽  
Time Resolved ◽  
Low Pressure Turbine ◽  
Turbine Vane ◽  
Vane Clocking

Aerodynamic measurements were acquired on a modern single-stage, transonic, high-pressure turbine with the adjacent low-pressure turbine vane row (a typical civilian one and one-half stage turbine rig) to observe the effects of low-pressure turbine vane clocking on overall turbine performance. The turbine rig (loosely referred to in this paper as the stage) was operated at design corrected conditions using the Ohio State University Gas Turbine Laboratory Turbine Test Facility. The research program utilized uncooled hardware in which all three airfoils were heavily instrumented at multiple spans to develop a full clocking dataset. The low-pressure turbine vane row (LPTV) was clocked relative to the high-pressure turbine vane row (HPTV). Various methods were used to evaluate the influence of clocking on the aeroperformance (efficiency) and the aerodynamics (pressure loading) of the LPTV, including time-resolved and time-averaged measurements. A change in overall efficiency of approximately 2–3% due to clocking effects is demonstrated and could be observed using a variety of independent methods. Maximum efficiency is obtained when the time-average surface pressures are highest on the LPTV and the time-resolved surface pressure (both in the time domain and frequency domain) show the least amount of variation. The overall effect is obtained by integrating over the entire airfoil, as the three-dimensional (3D) effects on the LPTV surface are significant. This experimental data set validates several computational research efforts that suggested wake migration is the primary reason for the perceived effectiveness of vane clocking. The suggestion that wake migration is the dominate mechanism in generating the clocking effect is also consistent with anecdotal evidence that fully cooled engine rigs do not see a great deal of clocking effect. This is consistent since the additional disturbances induced by the cooling flows and∕or the combustor make it extremely difficult to find an alignment for the LPTV given the strong 3D nature of modern high-pressure turbine flows.

Influence of Hot Streak Temperature Ratio on Low Pressure Stage of a Vaneless Counter-Rotating Turbine

2007 ◽  
Author(s):  
Qingjun Zhao ◽  
Fei Tang ◽  
Huishe Wang ◽  
Jianyi Du ◽  
Xiaolu Zhao ◽  
...  
Keyword(s):  
Shock Wave ◽  
High Pressure ◽  
Secondary Flow ◽  
Low Pressure ◽  
Turbine Rotor ◽  
Temperature Ratio ◽  
High Pressure Turbine ◽  
Pressure Stage ◽  
Low Pressure Turbine ◽  
Hot Streak

In order to explore the influence of hot streak temperature ratio on low pressure stage of a Vaneless Counter-Rotating Turbine, three-dimensional multiblade row unsteady Navier-Stokes simulations have been performed. The predicted results show that hot streaks are not mixed out by the time they reach the exit of the high pressure turbine rotor. The separation of colder and hotter fluids is observed at the inlet of the low pressure turbine rotor. After making interactions with the inner-extending shock wave and outer-extending shock wave in the high pressure turbine rotor, the hotter fluid migrates towards the pressure surface of the low pressure turbine rotor, and the most of colder fluid migrates to the suction surface of the low pressure turbine rotor. The migrating characteristics of the hot streaks are predominated by the secondary flow in the low pressure turbine rotor. The effect of buoyancy on the hotter fluid is very weak in the low pressure turbine rotor. The results also indicate that the secondary flow intensifies in the low pressure turbine rotor when the hot streak temperature ratio is increased. The effects of the hot streak temperature ratio on the relative Mach number and the relative flow angle at the inlet of the low pressure turbine rotor are very remarkable. The isentropic efficiency of the Vaneless Counter-Rotating Turbine decreases as the hot streak temperature ratio is increased.

Design of an Intermediate Turbine Duct Downstream of a High Pressure Turbine

2016 ◽  
Author(s):  
Chaoshan Hou ◽  
Hu Wu
Keyword(s):  
High Pressure ◽  
Three Dimensional ◽  
Low Pressure ◽  
Aerodynamic Load ◽  
Duct Flow ◽  
Original Design ◽  
High Pressure Turbine ◽  
Intermediate Turbine Duct ◽  
Low Pressure Turbine ◽  
Inlet Conditions

The flow leaving the high pressure turbine should be guided to the low pressure turbine by an annular diffuser, which is called as the intermediate turbine duct. Flow separation, which would result in secondary flow and cause great flow loss, is easily induced by the negative pressure gradient inside the duct. And such non-uniform flow field would also affect the inlet conditions of the low pressure turbine, resulting in efficiency reduction of low pressure turbine. Highly efficient intermediate turbine duct cannot be designed without considering the effects of the rotating row of the high pressure turbine. A typical turbine model is simulated by commercial computational fluid dynamics method. This model is used to validate the accuracy and reliability of the selected numerical method by comparing the numerical results with the experimental results. An intermediate turbine duct with eight struts has been designed initially downstream of an existing high pressure turbine. On the basis of the original design, the main purpose of this paper is to reduce the net aerodynamic load on the strut surface and thus minimize the overall duct loss. Full three-dimensional inverse method is applied to the redesign of the struts. It is revealed that the duct with new struts after inverse design has an improved performance as compared with the original one.

The Unsteady Flow Field of a Purged High Pressure Turbine Based on Mode Detection

2017 ◽  
Author(s):  
S. Zerobin ◽  
S. Bauinger ◽  
A. Marn ◽  
A. Peters ◽  
F. Heitmeir ◽  
...  
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Unsteady Flow ◽  
Flow Behavior ◽  
Low Pressure ◽  
Pressure Probe ◽  
Special Focus ◽  
High Pressure Turbine ◽  
Low Pressure Turbine ◽  
Mode Detection

This paper presents an experimental study of the unsteady flow field downstream of a high pressure turbine with ejected purge flows, with a special focus on a flow field discussion using the mode detection approach according to the theory of Tyler and Sofrin. Measurements were carried out in a product-representative one and a half stage turbine test setup, which consists of a high-pressure turbine stage followed by an intermediate turbine center frame and a low-pressure turbine vane row. Four independent purge mass flows were injected through the forward and aft cavities of the unshrouded high-pressure turbine rotor. A fast-response pressure probe was used to acquire time-resolved data at the turbine center frame duct inlet and exit. The interactions between the stator, rotor, and turbine center frame duct are identified as spinning modes, propagating in azimuthal direction. Time-space diagrams illustrate the amplitude variation of the detected modes along the span. The composition of the unsteadiness and its major contributors are of interest to determine the role of unsteadiness in the turbine center frame duct loss generation mechanisms and to avoid high levels of blade vibrations in the low-pressure turbine which can in turn result in increased acoustic emissions. This work offers new insight into the unsteady flow behavior downstream of a purged high-pressure turbine and its propagation through an engine-representative turbine center frame duct configuration.

Numerical Investigation of the Effect of Tip Leakage Flow on an Aggressive S-Shaped Intermediate Turbine Duct

2009 ◽  
Author(s):  
W. Sanz ◽  
M. Kelterer ◽  
R. Pecnik ◽  
A. Marn ◽  
E. Go¨ttlich
Keyword(s):  
High Pressure ◽  
Low Pressure ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
High Pressure Turbine ◽  
Tip Leakage ◽  
Intermediate Turbine Duct ◽  
Low Pressure Turbine ◽  
High Diffusion ◽  
Gap Height

The demand of a further increased bypass ratio of aero engines will lead to low pressure turbines with larger diameters which rotate at lower speed. Therefore, it is necessary to guide the flow leaving the high pressure turbine to the low pressure turbine at a larger diameter without any loss generating separation or flow disturbances. Due to costs and weight this intermediate turbine duct has to be as short as possible. This leads to an aggressive (high diffusion) S-shaped duct geometry. In order to investigate the influence of the blade tip gap height of a preceding rotor on such a high-diffusion duct flow a detailed measurement campaign in the Transonic Test Turbine Facility at Graz University of Technology has been performed. A high diffusion intermediate duct is arranged downstream a high-pressure turbine stage providing an exit Mach number of about 0.6 and a swirl angle of −15 degrees (counter swirl). A low-pressure vane row is located at the end of the duct and represents the counter rotating low pressure turbine at larger diameter. At the ASME 2007, results of these investigations were presented for two different tip gap heights of 1.5% span (0.8 mm) and 2.4% span (1.3 mm). In order to better understand the flow phenomena observed in the intermediate duct a detailed numerical study is conducted. The unsteady flow through the whole configuration is simulated for both gap heights as well as for a rotor with zero gap height. The unsteady data are compared at the stage exit and inside the duct to study the flow physics. The calculation of the zero gap height configuration allows to determine the influence of the tip leakage flow of the preceding rotor on the intermediate turbine duct. It turns out that for this aggressive duct the tip leakage flow has a very positive effect on the pressure recovery.

Experimental and Numerical Investigation of the Unsteady Surface Pressure in a Three-Stage Model of an Axial High Pressure Turbine

2004 ◽  
Vol 128 (2) ◽  
pp. 261-272 ◽  
Author(s):  
Carmen E. Kachel ◽  
John D. Denton
Keyword(s):  
High Pressure ◽  
Velocity Field ◽  
Surface Pressure ◽  
Pressure Field ◽  
Pressure Fluctuations ◽  
Pressure Waves ◽  
Stage Model ◽  
Unsteady Pressure ◽  
Unsteady Surface Pressure ◽  
Blade Row

This paper presents the results of a numerical and experimental investigation of the unsteady pressure field in a three-stage model of a high pressure steam turbine. Unsteady surface pressure measurements were taken on a first and second stage stator blade, respectively. The measurements in the blade passage were supplemented by time resolved measurements between the blade rows. The explanation of the origin of the unsteady pressure fluctuations was supported by unsteady three-dimensional computational fluid dynamic calculations of which the most extensive calculation was performed over two stages. The mechanisms affecting the unsteady pressure field were: the potential field frozen to the upstream blade row, the pressure waves originating from changes in the potential pressure field, the convected unsteady velocity field, and the passage vortex of the upstream blade row. One-dimensional pressure waves and the unsteady variation of the pitchwise pressure gradient due to the changing velocity field were the dominant mechanisms influencing the magnitude of the surface pressure fluctuations. The magnitude of these effects had not been previously anticipated to be more important than other recognized effects.

Sign in / Sign up

Export Citation Format

Share Document