On the Role of Leading-Edge Bumps in the Control of Stall Onset in Axial Fan Blades

2013 ◽  
Vol 135 (8) ◽  
Author(s):  
Alessandro Corsini ◽  
Giovanni Delibra ◽  
Anthony G. Sheard
Keyword(s):  
Numerical Study ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Axial Fan ◽  
Early Recovery ◽  
Viscosity Models ◽  
Flow Mechanisms ◽  
The Impact

Taking a lead from the humpback whale flukes, characterized by a series of bumps that result in a sinusoidal-like leading edge, this paper reports on a three-dimensional numerical study of sinusoidal leading edges on cambered airfoil profiles. The turbulent flow around the cambered airfoil with the sinusoidal leading edge was computed at different angles of attack with the open source solver OpenFOAM, using two different eddy viscosity models integrated to the wall. The reported research focused on the effects of the modified leading edge in terms of lift-to-drag performance and the influence of camber on such parameters. For these reasons a comparison with a symmetric airfoil is provided. The research was primarily concerned with the elucidation of the fluid flow mechanisms induced by the bumps and the impact of those mechanisms on airfoil performance, on both symmetric and cambered profiles. The bumps on the leading edge influenced the aerodynamic performance of the airfoil, and the lift curves were found to feature an early recovery in post-stall for the symmetric profile with an additional gain in lift for the cambered profile. The bumps drove the fluid dynamic on the suction side of the airfoil, which in turn resulted in the capability to control the separation at the trailing edge in coincidence with the peak of the sinusoid at the leading edge.

A study of fan-distortion interaction within the fan rotor

2020 ◽  
pp. 095765092092004
Author(s):  
Zhihui Li ◽  
Juan Du ◽  
Qianfeng Zhang ◽  
Guofeng Ji ◽  
Hongwu Zhang
Keyword(s):  
High Performance ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Stagnation Pressure ◽  
Detached Eddy Simulation ◽  
Axial Fan ◽  
Fan Performance ◽  
Inlet Distortion

Boundary-layer-ingesting fans and compressors in the next-generation turbofan engines require high-performance operations under distorted inflow. The aim of this work is to study the effects of inlet distortions including inlet stagnation pressure and temperature distortion, on the aerodynamic performance of a transonic axial fan. Firstly, the validated full-annulus, unsteady, three-dimensional computational fluid dynamic code in conjunction with detached Eddy simulation approach is used here to simulate the fan flows assembly with individual inlet stagnation pressure/temperature distortion. Then, the propagation process of the inlet distortion waves is analyzed to understand how the aerodynamic performance degradation is triggered. The simulation results show that the fan performance is remarkably degraded when the inlet distortion is introduced. The leading-edge spillage, the trailing edge back flow and the “tornado vortex” occur when parts of fan blades encounter the incoming distorted flows. Finally, the responses of fan to the combined inlet stagnation distortion effects are discussed in this paper. It is found that the combined distortion effects can be predicted based on the sum of the performance responses to the individual constituent distortions. Furthermore, the relative location of the constituent distortions shows a non-ignorable influence on the overall fan performance, especially for the intensified inlet distortion.

Quantitative CFD Analyses of Particle Deposition on a Subsonic Axial Compressor Blade

2015 ◽  
Author(s):  
Alessio Suman ◽  
Rainer Kurz ◽  
Nicola Aldi ◽  
Mirko Morini ◽  
Klaus Brun ◽  
...  
Keyword(s):  
Particle Deposition ◽  
Fluid Dynamic ◽  
Axial Compressor ◽  
Leading Edge ◽  
Suction Side ◽  
Sticking Probability ◽  
Particle Impact ◽  
Kinematic Characteristics ◽  
The Impact ◽  
Dynamic Phenomena

In literature there are some studies related to the fouling phenomena in transonic compressors, but, in industrial applications (heavy-duty compressor, pump stations, etc.) the subsonic compressors are widespread. It is of great interest to the manufacturer to discover the fouling phenomenon related to this type of compressor. This paper presents three-dimensional numerical simulations of the micro-particle ingestion on a subsonic axial compressor rotor carried out by means of a commercial computational fluid dynamic code. Particle trajectory simulations use a stochastic Lagrangian tracking method that solves the equations of motion separate from the continuous phase. The number of particles, sizes, and concentrations are specified in order to perform a quantitative analysis of the particle impact on the blade surface. In this paper the particle impact pattern and the kinematic characteristics (velocity and angle) of the impact are shown. Both of the blade zones affected by particle impact and the blade zones affected by particle deposition are analyzed. The particle deposition is established by using the quantity called sticking probability. The sticking probability links the kinematic characteristics of particle impact on the blade with fouling phenomenon. The results show that micro-particles tend to follow the flow by impacting at full span with a higher impact concentration on the leading edge. The suction side is affected only close to the leading edge and, at the hub, close to the trailing edge. Particular fluid-dynamic phenomena such as separation, stagnation and tip leakage vortex strongly influence the impact location of the particles. The kinematic analysis showed a high tendency of particle adhesion on the suction side, especially for smaller particles for which the fluid dynamic phenomena play a key role regarding particle impact velocity and angle.

Aerothermal Investigations of Mixing Flow Phenomena in Case of Radially Inclined Ejection Holes at the Leading Edge

1999 ◽  
Vol 122 (2) ◽  
pp. 334-339 ◽  
Author(s):  
Dieter E. Bohn ◽  
Karsten A. Kusterer
Keyword(s):  
Secondary Flow ◽  
Gas Turbines ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Back Side ◽  
Stagnation Line ◽  
Flow Phenomena ◽  
The Impact

A leading edge cooling configuration is investigated numerically by application of a three-dimensional conjugate fluid flow and heat transfer solver, CHT-flow. The code has been developed at the Institute of Steam and Gas Turbines, Aachen University of Technology. It works on the basis of an implicit finite volume method combined with a multiblock technique. The cooling configuration is an axial turbine blade cascade with leading edge ejection through two rows of cooling holes. The rows are located in the vicinity of the stagnation line, one row on the suction side, the other row is on the pressure side. The cooling holes have a radial ejection angle of 45 deg. This configuration has been investigated experimentally by other authors and the results have been documented as a test case for numerical calculations of ejection flow phenomena. The numerical investigations focus on the aerothermal mixing process in the cooling jets and the impact on the temperature distribution on the blade surface. The radial ejection angles lead to a fully three-dimensional and asymmetric jet flow field. Within a secondary flow analysis, the cooling fluid jets are investigated in detail. The secondary flow fields include asymmetric kidney vortex systems with one dominating vortex on the back side of the jets. The numerical and experimental data show a respectable agreement concerning the vortex development. [S0889-504X(00)00102-1]

Predicting Blade Leading Edge Erosion in an Axial Induced Draft Fan

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Alessandro Corsini ◽  
Andrea Marchegiani ◽  
Franco Rispoli ◽  
Paolo Venturini ◽  
Anthony G. Sheard
Keyword(s):  
Numerical Study ◽  
Fluid Dynamic ◽  
Leading Edge ◽  
Combustion Products ◽  
Aerodynamic Performance ◽  
Interpolation Scheme ◽  
Axial Fan ◽  
Critical Limit ◽  
Induced Draft Fan ◽  
Blade Leading Edge

Induced draft fans extract coal fired boiler combustion products, including particles of un-burnt coal and ash. As a consequence of the particles, the axial fan blades’ leading edges are subject to erosion. Erosion results in the loss of the blade leading edge aerodynamic profile and a reduction of blade chord and effective camber that together degrade aerodynamic performance. An experimental study demonstrated that while the degradation of aerodynamic performance begins gradually, it collapses as blade erosion reaches a critical limit. This paper presents a numerical study on the evolution of blade leading edge erosion patterns in an axial induced draft fan. The authors calculated particle trajectories using an in-house computational fluid dynamic (CFD) solver coupled with a trajectory predicting solver based on an original finite element interpolation scheme. The numerical study clarifies the influence of flow structure, initial blade geometry, particle size, and concentration on erosion pattern.

scholarly journals Drops bouncing off macro-textured superhydrophobic surfaces

2017 ◽  
Vol 824 ◽  
pp. 866-885 ◽  
Author(s):  
Ali Mazloomi Moqaddam ◽  
Shyam S. Chikatamarla ◽  
Iliya V. Karlin
Keyword(s):  
Contact Time ◽  
Numerical Study ◽  
Three Dimensional ◽  
Superhydrophobic Surfaces ◽  
Nonlinear Behaviour ◽  
Textured Surfaces ◽  
Texture Density ◽  
Wide Range ◽  
Quantitative Manner ◽  
The Impact

Recent experiments with droplets impacting macro-textured superhydrophobic surfaces revealed new regimes of bouncing with a remarkable reduction of the contact time. Here we present a comprehensive numerical study that reveals the physics behind these new bouncing regimes and quantifies the roles played by various external and internal forces. For the first time, accurate three-dimensional simulations involving realistic macro-textured surfaces are performed. After demonstrating that simulations reproduce experiments in a quantitative manner, the study is focused on analysing the flow situations beyond current experiments. We show that the experimentally observed reduction of contact time extends to higher Weber numbers, and analyse the role played by the texture density. Moreover, we report a nonlinear behaviour of the contact time with the increase of the Weber number for imperfectly coated textures, and study the impact on tilted surfaces in a wide range of Weber numbers. Finally, we present novel energy analysis techniques that elaborate and quantify the interplay between the kinetic and surface energy, and the role played by the dissipation for various Weber numbers.

The Impact of Predried Lignite Cofiring With Hard Coal in an Industrial Scale Pulverized Coal Fired Boiler

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Halina Pawlak-Kruczek ◽  
Robert Lewtak ◽  
Zbigniew Plutecki ◽  
Marcin Baranowski ◽  
Michal Ostrycharczyk ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Bituminous Coal ◽  
Cfd Simulation ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Industrial Scale ◽  
Hard Coal ◽  
Cfd Simulations ◽  
Reference Case ◽  
The Impact

The paper presents the experimental and numerical study on the behavior and performance of an industrial scale boiler during combustion of pulverized bituminous coal with various shares of predried lignite. The experimental measurements were carried out on a boiler WP120 located in CHP, Opole, Poland. Tests on the boiler were performed during low load operation and the lignite share reached over to 36% by mass. The predried lignite, kept in dedicated separate bunkers, was mixed with bituminous coal just before the coal mills. Computational fluid dynamic (CFD) simulation of a cofiring scenario of lignite with hard coal was also performed. Site measurements have proven that cofiring of a predried lignite is not detrimental to the boiler in terms of its overall efficiency, when compared with a corresponding reference case, with 100% of hard coal. Experiments demonstrated an improvement in the grindability that can be achieved during co-milling of lignite and hard coal in the same mill, for both wet and dry lignite. Moreover, performed tests delivered empirical evidence of the potential of lignite to decrease NOx emissions during cofiring, for both wet and dry lignite. Results of efficiency calculations and temperature measurements in the combustion chamber confirmed the need to predry lignite before cofiring. Performed measurements of temperature distribution in the combustion chamber confirmed trend that could be seen in the results of CFD. CFD simulations were performed for predried lignite and demonstrated flow patterns in the combustion chamber of the boiler, which could prove useful in case of any further improvements in the firing system. CFD simulations reached satisfactory agreement with the site measurements in terms of the prediction of emissions.

scholarly journals Experimental and numerical study on the performance of an axial fan with a Gurney flap

2018 ◽  
Vol 10 (10) ◽  
pp. 168781401880380 ◽  
Author(s):  
Liu Chen ◽  
Haijun Xie ◽  
Jun Xu ◽  
Ren Dai ◽  
Jian Chen
Keyword(s):  
Computational Fluid Dynamic ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Pressure Rise ◽  
Field Analysis ◽  
Horizontal Wind ◽  
Tip Leakage Flow ◽  
Axial Fan ◽  
Gurney Flap ◽  
Lift Enhancement

Gurney flap is a miniature lift-enhancement device installed at the airfoil trailing edge and has been successfully applied to fixed wing aircraft and low-speed horizontal wind turbines. In this article, Gurney flap is extended to increase pressure output of a diffusive cascade flow in rotating turbomachinery, which is complicated for its three dimensionalities and diffusive separation characteristics. Wind tunnel tests and computational fluid dynamic simulations were accomplished on an axial fan profiled with an NACA 65-(12)10 airfoil to investigate the effects of Gurney flap on the performance of a high solidity. We present the detailed flow features of the fan with and without Gurney flap after validating the simulation results with the experimental datum. The experimental results show positive Gurney flap effects on fan’s pressure rise and flow rate improvement. However, negative Gurney flap effects on fan’s efficiency are more evident than Gurney flap on isolated airfoils. Detailed flow field analysis from computational fluid dynamic computation reveals that the increased airfoil pressure loading along the fan blade chord strengthens the tip leakage flow, which induces more tip second flow losses than in the baseline fan. In addition to the positive lift enhancement, the net Gurney flap effect in diffusion cascade is influenced by the three-dimensional flow structure.

Clocking Effects of Inlet Non-Uniformities in a Fully Cooled High-Pressure Vane: A Conjugate Heat Transfer Analysis

2015 ◽  
Author(s):  
Duccio Griffini ◽  
Massimiliano Insinna ◽  
Simone Salvadori ◽  
Francesco Martelli
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Cooling System ◽  
Hot Spot ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Heat Transfer Analysis

A high-pressure vane equipped with a realistic film-cooling configuration has been studied. The vane is characterized by the presence of multiple rows of fan-shaped holes along pressure and suction side while the leading edge is protected by a showerhead system of cylindrical holes. Steady three-dimensional Reynolds-Averaged Navier-Stokes (RANS) simulations have been performed. A preliminary grid sensitivity analysis with uniform inlet flow has been used to quantify the effect of spatial discretization. Turbulence model has been assessed in comparison with available experimental data. The effects of the relative alignment between combustion chamber and high-pressure vanes are then investigated considering realistic inflow conditions in terms of hot spot and swirl. The inlet profiles used are derived from the EU-funded project TATEF2. Two different clocking positions are considered: the first one where hot spot and swirl core are aligned with passage and the second one where they are aligned with the leading edge. Comparisons between metal temperature distributions obtained from conjugate heat transfer simulations are performed evidencing the role of swirl in determining both the hot streak trajectory within the passage and the coolant redistribution. The leading edge aligned configuration is resulted to be the most problematic in terms of thermal load, leading to increased average and local vane temperature peaks on both suction side and pressure side with respect to the passage aligned case. A strong sensitivity of both injected coolant mass flow and heat removed by heat sink effect has also been highlighted for the showerhead cooling system.

HP Vane Aerodynamics and Heat Transfer in the Presence of Aggressive Inlet Swirl

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Imran Qureshi ◽  
Andy D. Smith ◽  
Thomas Povey
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Three Dimensional ◽  
Leading Edge ◽  
Good Deal ◽  
Vortex Center ◽  
Research Facility ◽  
Lean Burn ◽  
Numerical Predictions ◽  
The Impact

Modern lean burn combustors now employ aggressive swirlers to enhance fuel-air mixing and improve flame stability. The flow at combustor exit can therefore have high residual swirl. A good deal of research concerning the flow within the combustor is available in open literature. The impact of swirl on the aerodynamic and heat transfer characteristics of an HP turbine stage is not well understood, however. A combustor swirl simulator has been designed and commissioned in the Oxford Turbine Research Facility (OTRF), previously located at QinetiQ, Farnborough UK. The swirl simulator is capable of generating an engine-representative combustor exit swirl pattern. At the turbine inlet plane, yaw and pitch angles of over ±40 deg have been simulated. The turbine research facility used for the study is an engine scale, short duration, rotating transonic turbine, in which the nondimensional parameters for aerodynamics and heat transfer are matched to engine conditions. The research turbine was the unshrouded MT1 design. By design, the center of the vortex from the swirl simulator can be clocked to any circumferential position with respect to HP vane, and the vortex-to-vane count ratio is 1:2. For the current investigation, the clocking position was such that the vortex center was aligned with the vane leading edge (every second vane). Both the aligned vane and the adjacent vane were characterized. This paper presents measurements of HP vane surface and end wall heat transfer for the two vane positions. The results are compared with measurements conducted without swirl. The vane surface pressure distributions are also presented. The experimental measurements are compared with full-stage three-dimensional unsteady numerical predictions obtained using the Rolls Royce in-house code Hydra. The aerodynamic and heat transfer characterization presented in this paper is the first of its kind, and it is hoped to give some insight into the significant changes in the vane flow and heat transfer that occur in the current generation of low NOx combustors. The findings not only have implications for the vane aerodynamic design, but also for the cooling system design.

Three-Dimensional CFD Analysis of Meshing Losses in a Spur Gear Pair

2018 ◽  
Author(s):  
T. Fondelli ◽  
D. Massini ◽  
A. Andreini ◽  
B. Facchini ◽  
F. Leonardi
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Spur Gear ◽  
Computational Domain ◽  
Gear Pair ◽  
Transient Pressure ◽  
Numerical Effort ◽  
Free Environment

The reduction of fluid-dynamic losses in high speed gearing systems is nowadays increasing importance in the design of innovative aircraft propulsion systems, which are particularly focused on improving the propulsive efficiency. Main sources of fluid-dynamic losses in high speed gearing systems are windage losses, inertial losses resulting by impinging oil jets used for jet lubrication and the losses related to the compression and the subsequent expansion of the fluid trapped between gears teeth. The numerical study of the latter is particularly challenging since it faces high speed multiphase flows interacting with moving surfaces, but it paramount for improving knowledge of the fluid behavior in such regions. The current work aims to analyze trapping losses in a gear pair by means of three-dimensional CFD simulations. In order to reduce the numerical effort, an approach for restricting computational domain was defined, thus only a portion of the gear pair geometry was discretized. Transient calculations of a gear pair rotating in an oil-free environment were performed, in the context of conventional eddy viscosity models. Results were compared with experimental data from the open literature in terms of transient pressure within a tooth space, achieving a good agreement. Finally, a strategy for meshing losses calculation was developed and results as a function of rotational speed were discussed.

Sign in / Sign up

Export Citation Format

Share Document