scholarly journals Accuracy of Individual Trabecula Segmentation Based Plate and Rod Finite Element Models in Idealized Trabecular Bone Microstructure

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Hong Wang ◽  
X. Sherry Liu ◽  
Bin Zhou ◽  
Ji Wang ◽  
Baohua Ji ◽  
...  
Keyword(s):  
Finite Element ◽  
Trabecular Bone ◽  
Computational Cost ◽  
Three Dimensional ◽  
Failure Behavior ◽  
Micro Computed Tomography ◽  
Promising Tool ◽  
Fold Reduction ◽  
Trabecular Microstructure ◽  
Trabecular Bone Microstructure

Currently, specimen-specific micro finite element (μFE) analysis based micro computed tomography (μCT) images have become a major computational tool for the assessment of the mechanical properties of human trabecular bone. Despite the fine characterization of the three-dimensional (3D) trabecular microstructure based on high-resolution μCT images, conventional μFE models with each voxel converted to an element are not efficient in predicting the nonlinear failure behavior of bone due to a prohibitive computational cost. Recently, a highly efficient individual trabecula segmentation (ITS)-based plate and rod (PR) modeling technique has been developed by substituting individual plates and rods with shell and beam elements, respectively. In this technical brief, the accuracy of novel PR μFE models was examined in idealized microstructure models over a broad range of trabecular thicknesses. The Young's modulus and yield strength predicted by simplified PR models strongly correlated with those of voxel models at various voxel sizes. The conversion from voxel models to PR models resulted in an ∼762-fold reduction in the largest model size and significantly accelerated the nonlinear FE analysis. The excellent predictive power of the PR μFE models, demonstrated in an idealized trabecular microstructure, provided a quantitative mechanical basis for this promising tool for an accurate and efficient assessment of trabecular bone mechanics and fracture risk.

scholarly journals Influence of Trabecular Bone on Peri-Implant Stress and Strain Based on Micro-CT Finite Element Modeling of Beagle Dog

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Sheng-hui Liao ◽  
Xing-hao Zhu ◽  
Jing Xie ◽  
Vikesh Kumar Sohodeb ◽  
Xi Ding
Keyword(s):  
Finite Element ◽  
Trabecular Bone ◽  
Equivalent Stress ◽  
Three Dimensional ◽  
Simplified Model ◽  
Stress And Strain ◽  
Refined Model ◽  
Bone Interface ◽  
Trabecular Microstructure ◽  
Trabecular Bone Microstructure

The objective of this investigation is to analyze the influence of trabecular microstructure modeling on the biomechanical distribution of the implant-bone interface. Two three-dimensional finite element mandible models, one with trabecular microstructure (a refined model) and one with macrostructure (a simplified model), were built. The values of equivalent stress at the implant-bone interface in the refined model increased compared with those of the simplified model and strain on the contrary. The distributions of stress and strain were more uniform in the refined model of trabecular microstructure, in which stress and strain were mainly concentrated in trabecular bone. It was concluded that simulation of trabecular bone microstructure had a significant effect on the distribution of stress and strain at the implant-bone interface. These results suggest that trabecular structures could disperse stress and strain and serve as load buffers.

The Effect of Trabecular Bone on the Mechanical Response of Human Mandible with Implant

2014 ◽  
Vol 695 ◽  
pp. 588-591
Author(s):  
Khairul Salleh Basaruddin ◽  
Ruslizam Daud
Keyword(s):  
Computed Tomography ◽  
Finite Element ◽  
Trabecular Bone ◽  
Static Analysis ◽  
Load Distribution ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Fe Model ◽  
Micro Computed Tomography ◽  
Bone Specimen

This study aims to investigate the influence of trabecular bone in human mandible bone on the mechanical response under implant load. Three dimensional voxel finite element (FE) model of mandible bone was reconstructed from micro-computed tomography (CT) images that were captured from bone specimen. Two FE models were developed where the first consists of cortical bone, trabecular bone and implants, and trabecular bone part was excluded in the second model. A static analysis was conducted on both models using commercial software Voxelcon. The results suggest that trabecular bone contributed to the strength of human mandible bone and to the effectiveness of load distribution under implant load.

Three-Dimensional Local Measurements of Bone Strain and Displacement: Comparison of Three Digital Volume Correlation Approaches

2015 ◽  
Vol 137 (7) ◽  
Author(s):  
Marco Palanca ◽  
Gianluca Tozzi ◽  
Luca Cristofolini ◽  
Marco Viceconti ◽  
Enrico Dall'Ara
Keyword(s):  
Trabecular Bone ◽  
Cortical Bone ◽  
Computational Cost ◽  
Three Dimensional ◽  
Digital Volume Correlation ◽  
Micro Computed Tomography ◽  
Local Approach ◽  
Accuracy And Precision ◽  
Local Measurements ◽  
The Difference

Different digital volume correlation (DVC) approaches are currently available or under development for bone tissue micromechanics. The aim of this study was to compare accuracy and precision errors of three DVC approaches for a particular three-dimensional (3D) zero-strain condition. Trabecular and cortical bone specimens were repeatedly scanned with a micro-computed tomography (CT). The errors affecting computed displacements and strains were extracted for a known virtual translation, as well as for repeated scans. Three DVC strategies were tested: two local approaches, based on fast-Fourier-transform (DaVis-FFT) or direct-correlation (DaVis-DC), and a global approach based on elastic registration and a finite element (FE) solver (ShIRT-FE). Different computation subvolume sizes were tested. Much larger errors were found for the repeated scans than for the virtual translation test. For each algorithm, errors decreased asymptotically for larger subvolume sizes in the range explored. Considering this particular set of images, ShIRT-FE showed an overall better accuracy and precision (a few hundreds microstrain for a subvolume of 50 voxels). When the largest subvolume (50–52 voxels) was applied to cortical bone, the accuracy error obtained for repeated scans with ShIRT-FE was approximately half of that for the best local approach (DaVis-DC). The difference was lower (250 microstrain) in the case of trabecular bone. In terms of precision, the errors shown by DaVis-DC were closer to the ones computed by ShIRT-FE (differences of 131 microstrain and 157 microstrain for cortical and trabecular bone, respectively). The multipass computation available for DaVis software improved the accuracy and precision only for the DaVis-FFT in the virtual translation, particularly for trabecular bone. The better accuracy and precision of ShIRT-FE, followed by DaVis-DC, were obtained with a higher computational cost when compared to DaVis-FFT. The results underline the importance of performing a quantitative comparison of DVC methods on the same set of samples by using also repeated scans, other than virtual translation tests only. ShIRT-FE provides the most accurate and precise results for this set of images. However, both DaVis approaches show reasonable results for large nodal spacing, particularly for trabecular bone. Finally, this study highlights the importance of using sufficiently large subvolumes, in order to achieve better accuracy and precision.

Finite Element Simulation: The Effects of Loading Modes at Different Anatomical Sites of Trabecular Bone on Morphological Indices

2013 ◽  
Vol 845 ◽  
pp. 266-270 ◽  
Author(s):  
Szali Januddi Fatihhi ◽  
Syahrom Ardiyansyah ◽  
Muhamad Noor Harun ◽  
A. Abdul Rahim Rabiatul ◽  
Abdullah Jaafar ◽  
...  
Keyword(s):  
Finite Element ◽  
Trabecular Bone ◽  
Elastic Behavior ◽  
Osteoporotic Bone ◽  
Failure Behavior ◽  
Micro Computed Tomography ◽  
Anatomic Site ◽  
Morphological Studies ◽  
Morphological Indices ◽  
Loading Modes

The relationship between morphological parameter and different type of loading orientation on elastic behavior and yielding of trabecular may provide insight towards osteoporotic bone losses during normal activities. This paper attempts to predict the elastic and failure behavior of different loading modes (tensile and compression) on anatomic sites and morphological indices through finite element (FE) simulation. Specimens extracted from bovine femoral trabecular bone were imaged using micro computed tomography (μCT). Morphological studies were done followed by FE analysis. Results demonstrated differences between yield behaviors on anatomic sites were reflected onto the morphological indices and the type of loading modes. The yield initiated earlier in rod-like than plate-like trabecular in both loading condition but showed different failure behavior in rod-like trabecular with small differences in maximum stress between tensile and compressive. However, in many cases, trabecular models tend to have oblique fracture pattern in all anatomic sites. Through these findings, improved prediction of elastic properties and yield behavior by computational means provide insight in the development of bone substitute material depending on the anatomic site as well as in osteoporotic bone pathological treatment to monitor losses in trabecular struts.

Finite Element Study of the Cutting Mechanics of the Three Dimensional Rock Turning Process

2015 ◽  
Author(s):  
Demeng Che ◽  
Jacob Smith ◽  
Kornel F. Ehmann
Keyword(s):  
Finite Element ◽  
Oil And Gas ◽  
Three Dimensional ◽  
Polycrystalline Diamond ◽  
Close Correlation ◽  
Experimental Results ◽  
Failure Behavior ◽  
Fe Model ◽  
Gas Drilling ◽  
Cutting Mechanics

The unceasing improvements of polycrystalline diamond compact (PDC) cutters have pushed the limits of tool life and cutting efficiency in the oil and gas drilling industry. However, the still limited understanding of the cutting mechanics involved in rock cutting/drilling processes leads to unsatisfactory performance in the drilling of hard/abrasive rock formations. The Finite Element Method (FEM) holds the promise to advance the in-depth understanding of the interactions between rock and cutters. This paper presents a finite element (FE) model of three-dimensional face turning of rock representing one of the most frequent testing methods in the PDC cutter industry. The pressure-dependent Drucker-Prager plastic model with a plastic damage law was utilized to describe the elastic-plastic failure behavior of rock. A newly developed face turning testbed was introduced and utilized to provide experimental results for the calibration and validation of the formulated FE model. Force responses were compared between simulations and experiments. The relationship between process parameters and force responses and the mechanics of the process were discussed and a close correlation between numerical and experimental results was shown.

scholarly journals Prediction of Residual Stresses in a Multipass Pipe Weld by a Novel 3D Finite Element Approach

2018 ◽  
Author(s):  
Hui Huang ◽  
Jian Chen ◽  
Blair Carlson ◽  
Hui-Ping Wang ◽  
Paul Crooker ◽  
...  
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
High Performance ◽  
Large Scale ◽  
Graphics Processing Unit ◽  
Computational Cost ◽  
Three Dimensional ◽  
Processing Unit ◽  
Girth Welds ◽  
Welding Processes

Due to enormous computation cost, current residual stress simulation of multipass girth welds are mostly performed using two-dimensional (2D) axisymmetric models. The 2D model can only provide limited estimation on the residual stresses by assuming its axisymmetric distribution. In this study, a highly efficient thermal-mechanical finite element code for three dimensional (3D) model has been developed based on high performance Graphics Processing Unit (GPU) computers. Our code is further accelerated by considering the unique physics associated with welding processes that are characterized by steep temperature gradient and a moving arc heat source. It is capable of modeling large-scale welding problems that cannot be easily handled by the existing commercial simulation tools. To demonstrate the accuracy and efficiency, our code was compared with a commercial software by simulating a 3D multi-pass girth weld model with over 1 million elements. Our code achieved comparable solution accuracy with respect to the commercial one but with over 100 times saving on computational cost. Moreover, the three-dimensional analysis demonstrated more realistic stress distribution that is not axisymmetric in hoop direction.

scholarly journals Spatial Correlations of Trabecular Bone Microdamage with Local Stresses and Strains Using Rigid Image Registration

2011 ◽  
Vol 133 (6) ◽  
Author(s):  
Srinidhi Nagaraja ◽  
Oskar Skrinjar ◽  
Robert E. Guldberg
Keyword(s):  
Finite Element ◽  
Image Registration ◽  
Trabecular Bone ◽  
Tissue Level ◽  
Micro Ct ◽  
Micro Computed Tomography ◽  
Element Analysis ◽  
Registration Algorithm ◽  
Local Bone ◽  
Local Stresses

Although microdamage is known to accumulate in trabecular bone with overloading and aging, the tissue-level stresses and strains associated with local bone failure are not well known. Local correlation of microdamage with microstructural stresses and strains requires methods to accurately register histological sections with micro-computed tomography (micro-CT) based finite element models. In addition, the resolution of correlation (i.e., grid size) selected for analysis may affect the observed results. Therefore, an automated, repeatable, and accurate image registration algorithm was developed to determine the range of local stresses and strains associated with microdamage initiation. Using a two-dimensional rigid registration algorithm, bone structures from histology and micro-CT imaging were aligned. Once aligned, microdamaged regions were spatially correlated with local stresses and strains obtained from micro-CT based finite element analysis. Using this more sophisticated registration technique, we were able to analyze the effects of varying spatial grid resolution on local stresses and strains initiating microdamage. The results indicated that grid refinement to the individual pixel level (pixel-by-pixel method) more precisely defined the range of microdamage initiation compared to manually selected individual damaged and undamaged trabeculae. Using the pixel-by-pixel method, we confirmed that trabecular bone from younger cows sustained higher local strains prior to microdamage initiation compared to older bone.

scholarly journals Testing hypotheses for the function of the carnivoran baculum using finite-element analysis

2018 ◽  
Vol 285 (1887) ◽  
pp. 20181473 ◽  
Author(s):  
Charlotte A. Brassey ◽  
James D. Gardiner ◽  
Andrew C. Kitchener
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Computational Simulation ◽  
Compressive Loading ◽  
Three Dimensional ◽  
Negative Relationship ◽  
Micro Computed Tomography ◽  
Element Analysis ◽  
Duration Of Copulation ◽  
Shape Complexity

The baculum (os penis) is a mineralized bone within the glans of the mammalian penis and is one of the most morphologically diverse structures in the mammal skeleton. Recent experimental work provides compelling evidence for sexual selection shaping the baculum, yet the functional mechanism by which this occurs remains unknown. Previous studies have tested biomechanical hypotheses for the role of the baculum based on simple metrics such as length and diameter, ignoring the wealth of additional shape complexity present. For the first time, to our knowledge, we apply a computational simulation approach (finite-element analysis; FEA) to quantify the three-dimensional biomechanical performance of carnivoran bacula (n= 74) based upon high-resolution micro-computed tomography scans. We find a marginally significant positive correlation between sexual size dimorphism and baculum stress under compressive loading, counter to the ‘vaginal friction’ hypothesis of bacula becoming more robust to overcome resistance during initial intromission. However, a highly significant negative relationship exists between intromission duration and baculum stress under dorsoventral bending. Furthermore, additional FEA simulations confirm that the presence of a ventral groove would reduce deformation of the urethra. We take this as evidence in support of the ‘prolonged intromission’ hypothesis, suggesting the carnivoran baculum has evolved in response to pressures on the duration of copulation and protection of the urethra.

Sign in / Sign up

Export Citation Format

Share Document