On Finite Bending of Pressurized Tubes

1959 ◽  
Vol 26 (3) ◽  
pp. 386-392
Author(s):  
Eric Reissner
Keyword(s):  
Internal Pressure ◽  
Cross Sections ◽  
Linear Problem ◽  
Bending Moments ◽  
Pure Bending ◽  
Stability Parameters ◽  
Essential Step ◽  
Circular Rings ◽  
The Stability ◽  
Finite Bending

Abstract A unified treatment is presented of two well-known problems which have until now been considered separately. The two problems are: (a) the linear problem of pure bending of curved tubes, and (b) the nonlinear problem of pure bending of straight tubes. In both problems the effect of uniform internal pressure is included. The essential step in the present analysis is the treatment of the flattening of the cross sections of the tube by means of a theory of finite bending of circular rings. The general results of the paper are used to obtain improved values for the stability parameters in the problem of flattening instability of originally straight tubes acted upon by end bending moments, and also to obtain results on the effect of slight original curvature of the beam axis in the problem of flattening instability.

Proposal for Calculations of Flat Oval Pipes Under Internal Pressure Under Consideration of Material Plastification

1997 ◽  
Vol 119 (3) ◽  
pp. 301-305
Author(s):  
J. Jekerle
Keyword(s):  
Yield Strength ◽  
Internal Pressure ◽  
Wall Thickness ◽  
Cross Sections ◽  
Calculation Method ◽  
Bending Moments ◽  
Normal Stresses ◽  
Shear Forces ◽  
Elastic Bending ◽  
Bending Stresses

In the wall of an oval pipe, additional to the circumferential forces, shear forces and bending moments occur under internal pressure load. Under this condition, the bending stresses in certain cross sections reach a figure many times that of normal stresses so that yield strength of the material can be exceeded. The usual stress calculation method is based on the calculation of the bending moments with the use of the elastic bending equation. The use of the part-plastic equation presented in the paper gives more accurate values for the bending moments sought in the cross sections being checked. This paper shows that even though the new calculation method leads to a smaller wall thickness of the flat oval pipe, the design of the flat oval pipe is nevertheless safe.

An Analysis of Dissociation of Molecules in a High Resolution Electron Microscope

1973 ◽  
Vol 31 ◽  
pp. 486-487
Author(s):  
Mihir Parikh
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Cross Sections ◽  
Resolving Power ◽  
Peak Intensity ◽  
Molecular Film ◽  
Resolution Electron ◽  
Dissociation Cross Section ◽  
High Resolution Electron Microscope ◽  
The Stability

It is well known that the resolution of bio-molecules in a high resolution electron microscope depends not just on the physical resolving power of the instrument, but also on the stability of these molecules under the electron beam. Experimentally, the damage to the bio-molecules is commo ly monitored by the decrease in the intensity of the diffraction pattern, or more quantitatively by the decrease in the peaks of an energy loss spectrum. In the latter case the exposure, EC, to decrease the peak intensity from IO to I’O can be related to the molecular dissociation cross-section, σD, by EC = ℓn(IO /I’O) /ℓD. Qu ntitative data on damage cross-sections are just being reported, However, the microscopist needs to know the explicit dependence of damage on: (1) the molecular properties, (2) the density and characteristics of the molecular film and that of the support film, if any, (3) the temperature of the molecular film and (4) certain characteristics of the electron microscope used

The stability of rectangular thin-walled profile with loading according to the scheme of pure bending

2020 ◽  
pp. 41-45
Author(s):  
V.B. Zylev ◽  
◽  
P.O. Platnov ◽  
I.V. Alferov ◽  
◽  
...  
Keyword(s):  
Pure Bending ◽  
Thin Walled ◽  
The Stability

Experimentally Determined Stability Parameters of a Subsonic Cascade Oscillating Near Stall

1978 ◽  
Vol 100 (1) ◽  
pp. 111-120 ◽  
Author(s):  
F. O. Carta ◽  
A. O. St. Hilaire
Keyword(s):  
Phase Angle ◽  
Incidence Angle ◽  
Minor Effect ◽  
Significant Finding ◽  
Force Coefficient ◽  
Stability Parameters ◽  
Free System ◽  
Pressure Transducers ◽  
Moment Coefficient ◽  
The Stability

Tests were performed on a linear cascade of airfoils oscillating in pitch about their midchords at frequencies up to 17 cps, at free-stream velocities up to 200 ft/s, and at interblade phase angles of 0 deg and 45 deg, under conditions of high aerodynamic loading. The measured data included unsteady time histories from chordwise pressure transducers and from chordwise hot films. Unsteady normal force coefficient, moment coefficient, and aerodynamic work per cycle of oscillation were obtained from integrals of the pressure data, and indications of the nature and extent of the separation phenomenon were obtained from an analysis of the hot-film response data. The most significant finding of this investigation is that a change in interblade phase angle from 0 deg to 45 deg radically alters the character of the unsteady blade loading (which governs its motion in a free system) from stable to unstable. Furthermore, the stability or instability is governed primarily by the phase angle of the pressure distribution (relative to the blade motion) over the forward 10–15 percent of the blade chord. Reduced frequency and mean incidence angle changes were found to have a relatively minor effect on stability for the range of parameters tested.

A characteristic type of instability in the large deflexions of elastic plates III. Curved rectangular plates in axial compression

1954 ◽  
Vol 222 (1148) ◽  
pp. 44-59 ◽  
Keyword(s):  
Axial Compression ◽  
Rectangular Plates ◽  
Bending Moments ◽  
Elastic Plates ◽  
Characteristic Type ◽  
Circular Tubes ◽  
Axis Parallel ◽  
Post Buckling ◽  
Thin Walled ◽  
The Stability

The analysis of part I is extended to deal with the case of free-edged rectangular plates having an initial curvature about an axis parallel to one pair of opposite edges and loaded by distributed bending moments applied to the straight edges and compressive forces applied to the curved edges. In particular, the stability and post-buckling behaviour of such plates subjected to the compressive forces alone is studied. The axially symmetrical buckling of thin-walled circular tubes in axial compression is also considered. Experimental plates are found to buckle at loads rather lower than those predicted.

The Accepting of Pipe Bends With Ovality and Thinning Using Finite Element Method

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
AR. Veerappan ◽  
S. Shanmugam ◽  
S. Soundrapandian
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Internal Pressure ◽  
Cross Sections ◽  
Pressure Ratio ◽  
Empirical Relationship ◽  
The Finite Element Method ◽  
Element Method

Thinning and ovality are commonly observed irregularities in pipe bends, which induce higher stress than perfectly circular cross sections. In this work, the stresses introduced in pipe bends with different ovalities and thinning for a particular internal pressure are calculated using the finite element method. The constant allowable pressure ratio for different ovalities and thinning is presented at different bend radii. The allowable pressure ratio increases, attains a maximum, and then decreases as the values of ovality and thinning are increased. An empirical relationship to determine the allowable pressure in terms of bend ratio, pipe ratio, percent thinning, and percent ovality is presented. The pipe ratio has a strong effect on the allowable pressure.

Shakedown and Limit Analysis of Kinematic Hardening Piping Elbows Under Internal Pressure and Bending Moments

2021 ◽  
Author(s):  
Heng Peng ◽  
Yinghua Liu
Keyword(s):  
Yield Strength ◽  
Internal Pressure ◽  
Limit Analysis ◽  
Kinematic Hardening ◽  
Limit Load ◽  
Bending Moments ◽  
Plastic Limit ◽  
Plastic Limit Load ◽  
Interaction Curves ◽  
Shakedown Limit

Abstract In this paper, the Stress Compensation Method (SCM) adopting an elastic-perfectly-plastic (EPP) material is further extended to account for limited kinematic hardening (KH) material model based on the extended Melan's static shakedown theorem using a two-surface model defined by two hardening parameters, namely the initial yield strength and the ultimate yield strength. Numerical analysis of a cylindrical pipe is performed to validate the outcomes of the extended SCM. The results agree well with ones from literature. Then the extended SCM is applied to the shakedown and limit analysis of KH piping elbows subjected to internal pressure and cyclic bending moments. Various loading combinations are investigated to generate the shakedown limit and the plastic limit load interaction curves. The effects of material hardening, elbow angle and loading conditions on the shakedown limit and the plastic limit load interaction curves are presented and analysed. The present method is incorporated in the commercial finite element simulation software and can be considered as a general computational tool for shakedown analysis of KH engineering structures. The obtained results provide a useful information for the structural design and integrity assessment of practical piping elbows.

Pure Moment Testing for Spinal Biomechanics Applications: Fixed Versus 3D Floating Ring Cable-Driven Test Designs

2012 ◽  
Author(s):  
Jessica A. Tang ◽  
Justin K. Scheer ◽  
Christopher P. Ames ◽  
Jenni M. Buckley
Keyword(s):  
Spinal Column ◽  
Bending Moments ◽  
Pure Bending ◽  
Uniform Loading ◽  
Flexion Extension ◽  
Driven System ◽  
Accepted Standard ◽  
Pure Moment ◽  
Bending Modes ◽  
Biomechanical Tests

For spine biomechanical tests, the cable-driven system in particular has been widely used to apply pure bending moments. The advantages to pure moment testing lie in its consistency as an accepted standard protocol across previous literature and its ability to ensure uniform loading across all levels of the spinal column. Of the methods used for pure moment testing, cable-driven set-ups are popular due to their low requirements and simple design. Crawford et al [1] were the first to employ this method, but prior work by our group indicated a discrepancy between applied and intended moment for this system in flexion-extension only [2]. We hypothesize that this discrepancy can be observed in other bending modes and minimized with a second-generation floating ring design to eliminate off-axis loads.

Technical Basis for Application of Collapse Moments for Locally Thinned Pipes Subjected to Torsion and Bending Proposed for ASME Section XI

2014 ◽  
Author(s):  
Kunio Hasegawa ◽  
Yinsheng Li ◽  
Bostjan Bezensek ◽  
Phuong H. Hoang ◽  
Howard J. Rathbun
Keyword(s):  
Power Plants ◽  
Bending Moments ◽  
Finite Element Analyses ◽  
Pure Bending ◽  
Plastic Bending ◽  
Evaluation Procedures ◽  
Wall Thinning ◽  
Applicable Range ◽  
Technical Basis ◽  
Local Wall Thinning

Piping components in power plants may experience combined bending and torsion moments during operation. There is a lack of guidance for pipe evaluation for pipes with local wall thinning flaws under the combined bending and torsion moments. ASME B&PV Code Section XI Working Group is currently developing fully plastic bending pipe evaluation procedures for pressurized piping components containing local wall thinning subjected to combined torsion and bending moments. Using elastic fully plastic finite element analyses, plastic collapse bending moments under torsions were obtained for 4 (114.3) to 24 (609.6) inch (mm) diameter pipes with various local wall thinning flaw sizes. The objective of this paper is to introduce an equivalent moment, which combines torsion and bending moments by a vector summation, and to establish the applicable range of wall thinning lengths, angles and depths, where the equivalent moments are equal to pure bending moments.

Sign in / Sign up

Export Citation Format

Share Document