scholarly journals Discussion: “Effect of Bending Rigidity of Stringers Upon Stress Distribution in Reinforced Monocoque Cylinder Under Concentrated Transverse Loads” (Levy, R. S., 1948, ASME J. Appl. Mech., 15, pp. 30–36)

1948 ◽  
Vol 15 (4) ◽  
pp. 388
Author(s):  
M. Z. Krzywoblocki
Keyword(s):  
Stress Distribution ◽  
Bending Rigidity ◽  
Transverse Loads

Effect of Bending Rigidity of Stringers Upon Stress Distribution in Reinforced Monocoque Cylinder Under Concentrated Transverse Loads

1948 ◽  
Vol 15 (1) ◽  
pp. 30-36
Author(s):  
Robert S. Levy
Keyword(s):  
Stress Distribution ◽  
Present Method ◽  
Load Application ◽  
Shear Stresses ◽  
Bending Rigidity ◽  
Work Analysis ◽  
Rigidity Results ◽  
Transverse Loads ◽  
Strain Rosette ◽  
Good Agreement

Abstract Least-work analysis of stress distribution in a reinforced circular monocoque cylinder is extended to determine the effect of bending resistant stringers located at the points of application of concentrated transverse loads. Calculations for a numerical example, with applied loads diametrically opposed, indicate that neglect of stringer bending rigidity results in calculated maximum shear stresses approximately 20 per cent conservative in the fields of load application and 50 per cent unsafe in an intermediate field. Further calculations indicate that the bending rigidity of the stringer has less effect when all loads are applied at the same circumferential location. Comparison of shear stresses, calculated by the present method with strain-rosette readings, indicate good agreement.

Stresses in a Reinforced Monocoque Cylinder Under Concentrated Symmetric Transverse Loads

1944 ◽  
Vol 11 (4) ◽  
pp. A235-A239
Author(s):  
N. J. Hoff
Keyword(s):  
Shear Stress ◽  
Stress Distribution ◽  
Cross Section ◽  
Maximum Shear Stress ◽  
Circular Cross Section ◽  
Bending Moment ◽  
Normal Stress Distribution ◽  
Transverse Loads ◽  
Conventional Analysis ◽  
Analysis Application

Abstract The stresses in the sheet covering, stringers, and rings of a reinforced monocoque cylinder of circular cross section are calculated for the case of a loading consisting of concentrated symmetric forces applied to the rings in the planes of the rings. The conventional assumptions of a linear normal stress distribution and a corresponding shear-stress distribution in the bent cylinder are replaced by a least-work analysis. Application of the theory to the numerical example of a cantilever monocoque cylinder yields a maximum shear stress in the sheet covering and a maximum bending moment in the ring amounting to 900 per cent and 33 per cent, respectively, of the values obtained by the conventional analysis.

Analysis of Stress Distribution of Externally Pre-Stressed Beams under Transverse Loads

2012 ◽  
Vol 166-169 ◽  
pp. 3065-3070
Author(s):  
Peng Zhang ◽  
Dan Shen ◽  
Shi Rong Li
Keyword(s):  
Mechanical Properties ◽  
Stress Distribution ◽  
Normal Stress ◽  
Cross Section ◽  
Beam Theory ◽  
Reinforcing Steel ◽  
Analytical Formulation ◽  
Simply Supported ◽  
Transverse Loads ◽  
Steel Bars

The size, the position and the arrangement of external restraint will significantly affect the mechanical properties of the structures with the external restraint. Based on classical beam theory, the stress distribution of a simply supported beam with externally reinforcing steel bars under transverse loads is analyzed in this presentation. By assuming that the stresses in both the beam and the external constrains are less than their proportional limits, an analytical formulation of normal stress in the cross section of the beam was derived by considering two cases that the externally reinforcing steel bars are pre-stressed and are not pre-stressed. Influences of the parameters of the stiffness and the position of the externally reinforcing steel bars on the stress of the beam are discussed.

Local stress distribution and yielding of steel sheets due to concentrated transverse loads

2012 ◽  
Vol 82 (10-11) ◽  
pp. 1613-1626
Author(s):  
Ioannis G. Raftoyiannis ◽  
George T. Michaltsos
Keyword(s):  
Stress Distribution ◽  
Local Stress ◽  
Steel Sheets ◽  
Transverse Loads

The concerted use of SEM, TEM, and SCM for examination of resin-dentin interfaces

1994 ◽  
Vol 52 ◽  
pp. 476-477
Author(s):  
B. Van Meerbeek ◽  
L. J. Conn ◽  
E. S. Duke
Keyword(s):  
Surface Layer ◽  
Stress Distribution ◽  
Phosphoric Acid ◽  
Bonding Mechanism ◽  
Restorative Dentistry ◽  
Dental Adhesive ◽  
Low Viscosity ◽  
Dentin Adhesives ◽  
Acid Etch ◽  
Tooth Tissue

Restoration of decayed teeth with tooth-colored materials that can be bonded to tooth tissue has been a highly desirable property in restorative dentistry for many years. Advantages of such an adhesive restorative technique over conventional techniques using non-adhesive metal-based restoratives include improved restoration retention with minimal sacrifice of sound tooth tissue for retention purposes, superior adaptation and sealing of the restoration margins in prevention of caries recurrence, improved stress distribution across the tooth-restoration interface throughout the whole tooth, and even reinforcement of weakened tooth structures. The dental adhesive technology is rapidly changing. An efficient resin bond to enamel has already long been achieved. Its bonding mechanism has been fully elucidated and has proven to be a durable and reliable clinical treatment. However, bonding to dentin represents a greater challenge. After the failures of a dentin acid-etch technique in imitation of the enamel phosphoric-acid-etch technique and a bonding procedure based on chemical adhesion, modern dentin adhesives are currently believed to bond to dentin by a micromechanical hybridization process. This process is developed by an initial demineralization of the dentin surface layer with acid etchants exposing a collagen fibril arrangement with interfibrillar microporosities that subsequently become impregnated by low-viscosity monomers. Although the development of such a hybridization process has well been documented in the literature, questions remain with respect to parameters of-primary importance to adhesive efficacy.

Sign in / Sign up

Export Citation Format

Share Document