scholarly journals Rotating Flow and Heat Transfer in Cylindrical Cavities With Radial Inflow

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
B. G. Vinod Kumar ◽  
John W. Chew ◽  
Nicholas J. Hills
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Reynolds Stress ◽  
Integral Method ◽  
Eddy Viscosity ◽  
Reynolds Stress Model ◽  
Stress Model ◽  
Rotating Disc ◽  
Flow And Heat Transfer ◽  
Viscosity Models

The design and optimization of an efficient internal air system of a gas turbine requires a thorough understanding of the flow and heat transfer in rotating disc cavities. The present study is devoted to the numerical modeling of flow and heat transfer in a cylindrical cavity with radial inflow and a comparison with the available experimental data. The simulations are carried out with axisymmetric and 3-D sector models for various inlet swirl and rotational Reynolds numbers up to 1.2 × 106. The pressure coefficients and Nusselt numbers are compared with the available experimental data and integral method solutions. Two popular eddy viscosity models, the Spalart–Allmaras and the k-ɛ, and a Reynolds stress model have been used. For cases with particularly strong vortex behavior the eddy viscosity models show some shortcomings, with the Spalart–Allmaras model giving slightly better results than the k-ɛ model. Use of the Reynolds stress model improved the agreement with measurements for such cases. The integral method results are also found to agree well with the measurements.

scholarly journals Rotating Flow and Heat Transfer in Cylindrical Cavities With Radial Inflow

2012 ◽  
Author(s):  
B. G. Vinod Kumar ◽  
John W. Chew ◽  
Nicholas J. Hills
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Reynolds Stress ◽  
Integral Method ◽  
Eddy Viscosity ◽  
Reynolds Stress Model ◽  
Stress Model ◽  
Rotating Disc ◽  
Flow And Heat Transfer ◽  
Viscosity Models

Design and optimization of an efficient internal air system of a gas turbine requires thorough understanding of the flow and heat transfer in rotating disc cavities. The present study is devoted to numerical modelling of flow and heat transfer in a cylindrical cavity with radial inflow and comparison with the available experimental data. The simulations are carried out with axi-symmetric and 3-D sector models for various inlet swirl and rotational Reynolds numbers upto 2.1×106. The pressure coefficients and Nusselt numbers are compared with the available experimental data and integral method solutions. Two popular eddy viscosity models, the Spalart-Allmaras and the k-ε, and a Reynolds stress model have been used. For cases with particularly strong vortex behaviour the eddy viscosity models show some shortcomings with the Spalart-Allmaras model giving slightly better results than the k-ε model. Use of the Reynolds stress model improved the agreement with measurements for such cases. The integral method results are also found to agree well with the measurements.

Numerical Simulation of Flow and Heat Transfer Past a Turbine Blade With a Squealer-Tip

2002 ◽  
Author(s):  
Huitao Yang ◽  
Sumanta Acharya ◽  
Srinath V. Ekkad ◽  
Chander Prakash ◽  
Ron Bunker
Keyword(s):  
Heat Transfer ◽  
Reynolds Stress ◽  
Pressure Ratio ◽  
Reynolds Stress Model ◽  
Leakage Flow ◽  
Stress Model ◽  
Tip Leakage Flow ◽  
Transfer Coefficients ◽  
Model Calculations ◽  
Flow And Heat Transfer

Numerical calculations are performed to simulate the tip leakage flow and heat transfer on the squealer (recessed) tip of GE-E3 turbine rotor blade. A squealer tip with a 3.77% recess of the blade span is considered in this study, and the results are compared with the predictions for a flat-tip blade. The calculations have been performed for an isothermal blade with an overall pressure ratio of 1.32, an inlet turbulence intensity of 6.1%, and for three different tip gap clearances of 1%, 1.5% and 2.5% of the blade span. These conditions correspond to the experiments reported by Azad et al. [1]. The calculations have been performed for three different turbulence models (the standard high Re k-ε model, the RNG k-ε and the Reynolds Stress Model) in order to assess the capability of the models in correctly predicting the blade heat transfer. The predictions show good agreement with the experimental data, with the Reynolds stress model calculations clearly providing the best results. Substantial reductions in the tip heat transfer and leakage flow is obtained with the squealer tip configuration. With the squealer tip, the heat transfer coefficients on the shroud and on the suction surface of the blade are also considerably reduced.

Flow and Heat Transfer Predictions for a Flat-Tip Turbine Blade

2002 ◽  
Author(s):  
Huitao Yang ◽  
Sumanta Acharya ◽  
Srinath V. Ekkad ◽  
Chander Prakash ◽  
Ron Bunker
Keyword(s):  
Heat Transfer ◽  
Reynolds Stress ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Computational Effort ◽  
Stress Model ◽  
Tip Leakage Flow ◽  
Flow And Heat Transfer ◽  
Pitch Direction ◽  
Blade Tip

Numerical calculations are performed to simulate the tip leakage flow and heat transfer on the GE-E3 High-Pressure-Turbine (HPT) rotor blade. The calculations are performed for a single blade with periodic conditions imposed along the two boundaries in the circumferential-pitch direction. Cases considered are a flat blade tip at three different tip gap clearances of 1%, 1.5% and 2.5% of the blade span. The numerical results are obtained for two different pressure ratios (ratio of inlet total pressure to exit static pressure) of 1.2 and 1.32 and an inlet turbulence level of 6.1%. To explore the effect of turbulence models on the heat transfer results, three different models of increasing complexity and computational effort (standard high Re k-ε model, RNG k-ε and Reynolds Stress Model) are investigated. The predicted tip heat transfer results are compared with the experimental data of Azad [1], and show satisfactory agreement with the data. Hear transfer predictions for all three turbulence models are comparable, and no significant improvements are obtained with the Reynolds-stress model.

On the Application of the Full Reynolds Stress Model for Unsteady CFD in Hydraulic Turbomachines

2020 ◽  
Author(s):  
Ernesto Casartelli ◽  
Luca Mangani ◽  
David Roos ◽  
Armando Del Rio
Keyword(s):  
Reynolds Stress ◽  
Eddy Viscosity ◽  
Reynolds Stress Model ◽  
Moment Closure ◽  
Flow Structures ◽  
Stress Model ◽  
Cfd Simulations ◽  
Viscosity Models ◽  
Hydraulic Machines ◽  
Fully Coupled

Abstract The computation of the characteristic of hydraulic machines, both in pump and turbine mode, needs, when performed over a wide operating range, to take into account turbulence anisotropy. This because highly separated flows largely deviate from isotropic turbulence structures as assumed in RANS eddy viscosity models with the Boussinesq approximation. In this paper CFD computations were performed with anisotropic turbulence models in order to capture the characteristic and investigate flow structures phenomena. Experimental results are compared against the CFD simulations in order to validate the results. Specific occurring phenomena are highlighted and more complex flow structures are evident compared to those computed with standard eddy viscosity models. A in-house pressure based coupled solver was used for the CFD simulations. The code is a finite volume polyhedral CFD solver implemented in a C++ framework with the possibility to implement implicit and coupled algorithms. Second moment closure turbulence model have been successfully implemented with a standard and novel fully coupled algorithm. In the paper the advantage of the novel algorithm is presented for industrial applications. The fully coupled approach for the Reynolds Stress model allows stable simulations of transient and steady state hydraulic machines at any operating point, opening also new opportunities in obtaining high accurate results for anisotropic turbulent flows without the usage of hybrid LES/RANS models and without the model limitation of standard eddy viscosity models.

Two-Equation Versus Reynolds-Stress Modeling in Predicting Flow and Heat Transfer in a Smooth U-Duct With and Without Rotation

2002 ◽  
Author(s):  
X. Gu ◽  
H.-W. Wu ◽  
H. J. Schock ◽  
T. I.-P. Shih
Keyword(s):  
Heat Transfer ◽  
Reynolds Stress ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Surface Heat ◽  
Small Radius ◽  
Stress Model ◽  
Surface Heat Transfer ◽  
Flow And Heat Transfer ◽  
Significant Difference

Computations were performed by using Version 5.5 of the Fluent-UNS code to compare two turbulence models in predicting the three-dimensional flow and heat transfer in a smooth duct of square cross section with a small radius of curvature 180-degree bend under rotating and non-rotating conditions (Re = 25,000; Ro = 0.0 and 0.24). The two turbulence models investigated are the standard k-ε model and a Reynolds stress model. For both models, the two-layer low-Reynolds model of Chen and Patel was used in the near-wall region. Results obtained show that though the k-ε model predicts turbulence quantities incorrectly, the predicted velocity and temperature fields and the surface heat transfer are similar to those from the Reynolds stress model when there is no rotation. When there is rotation, there is significant difference in the predicted surface heat transfer on the leading surface. But, the predicted flow field is still qualitatively similar.

Improved Prediction of Turbomachinery Flows Using Near-Wall Reynolds-Stress Model

2001 ◽  
Vol 124 (1) ◽  
pp. 86-99 ◽  
Author(s):  
G. A. Gerolymos ◽  
J. Neubauer ◽  
V. C. Sharma ◽  
I. Vallet
Keyword(s):  
Experimental Data ◽  
Turbulent Flows ◽  
Reynolds Stress ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Stress Model ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Flow Equations ◽  
Near Wall

In this paper an assessment of the improvement in the prediction of complex turbomachinery flows using a new near-wall Reynolds-stress model is attempted. The turbulence closure used is a near-wall low-turbulence-Reynolds-number Reynolds-stress model, that is independent of the distance-from-the-wall and of the normal-to-the-wall direction. The model takes into account the Coriolis redistribution effect on the Reynolds-stresses. The five mean flow equations and the seven turbulence model equations are solved using an implicit coupled OΔx3 upwind-biased solver. Results are compared with experimental data for three turbomachinery configurations: the NTUA high subsonic annular cascade, the NASA_37 rotor, and the RWTH 1 1/2 stage turbine. A detailed analysis of the flowfield is given. It is seen that the new model that takes into account the Reynolds-stress anisotropy substantially improves the agreement with experimental data, particularily for flows with large separation, while being only 30 percent more expensive than the k−ε model (thanks to an efficient implicit implementation). It is believed that further work on advanced turbulence models will substantially enhance the predictive capability of complex turbulent flows in turbomachinery.

Sign in / Sign up

Export Citation Format

Share Document