Combustion Phasing Effect on Cycle Efficiency of a Diesel Engine Using Advanced Gasoline Fumigation

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
William F. Northrop ◽  
Wei Fang ◽  
Bin Huang
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Direct Injection ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Actual Performance ◽  
Conventional Combustion ◽  
Lower Heat ◽  
Gasoline Fumigation ◽  
Cycle Efficiency

Advanced premixed compression ignition (CI) combustion using fumigation has been shown to yield significant improvements in indicated efficiency over traditional diesel combustion strategies while simultaneously reducing engine-out soot and NOx emissions. To better interpret these findings, a breakdown of the ways in which actual performance deviates from ideal engine cycles is helpful. Nonideal combustion phasing is one cause of such deviations. In this paper, the centroid of the calculated apparent heat release rate is used to estimate an adjusted maximum possible thermal efficiency based on constant volume combustion using an effective compression ratio concept. Using these metrics, experimental engine data are evaluated from a single cylinder direct-injection diesel engine operating in premixed CI mode enabled by gasoline fumigation and a diesel pilot injection. Indicated gross cycle efficiency was found to be higher for premixed fumigation compared with a conventional diesel condition at the same load. A key finding of the work is that the peak indicated cycle efficiency for fumigated premixed CI combustion occurs with combustion phased very close to top dead center. Shorter heat release duration and lower heat losses from the cylinder are thought to be the cause of differences in cycle efficiency between conventional combustion and premixed CI fumigation modes.

Combustion Phasing Effect on Cycle Efficiency of a Diesel Engine Using Advanced Gasoline Fumigation

2012 ◽  
Author(s):  
William F. Northrop ◽  
Wei Fang ◽  
Bin Huang
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Direct Injection ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Actual Performance ◽  
Conventional Combustion ◽  
Lower Heat ◽  
Gasoline Fumigation ◽  
Cycle Efficiency

Advanced premixed compression ignition (CI) combustion using fumigation has been shown to yield significant improvements in indicated efficiency over traditional diesel combustion strategies while simultaneously reducing engine-out soot and NOX emissions. To better interpret these findings, a breakdown of the ways in which actual performance deviates from ideal engine cycles is helpful. Non-ideal combustion phasing is one cause of such deviations. In this paper, the centroid of the calculated apparent heat release rate is used to estimate an adjusted maximum possible thermal efficiency based on constant volume combustion using an effective compression ratio concept. Using these metrics, experimental engine data are evaluated from a single cylinder direct-injection diesel engine operating in premixed CI mode enabled by gasoline fumigation and a diesel pilot injection. Indicated gross cycle efficiency was found to be higher for premixed fumigation compared with a conventional diesel condition at the same load. A key finding of the work is that the peak indicated cycle efficiency for fumigated premixed CI combustion occurs with combustion phased very close to TDC. Shorter heat release duration and lower heat losses from the cylinder are thought to be the cause of differences in cycle efficiency between conventional combustion and premixed CI fumigation modes.

scholarly journals Effects of pilot injection timing and EGR on a modern V6 common rail direct injection diesel engine

2013 ◽  
Vol 50 ◽  
pp. 012008 ◽  
Author(s):  
Nik Rosli Abdullah ◽  
Rizalman Mamat ◽  
Miroslaw L Wyszynski ◽  
Anthanasios Tsolakis ◽  
Hongming Xu
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Common Rail ◽  
Injection Timing ◽  
Pilot Injection ◽  
Direct Injection Diesel Engine

scholarly journals The Effect of RME-1-Butanol Blends on Combustion, Performance and Emission of a Direct Injection Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2941
Author(s):  
Wojciech Tutak ◽  
Arkadiusz Jamrozik ◽  
Karol Grab-Rogaliński
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Direct Injection ◽  
Specific Energy Consumption ◽  
Combustion Process ◽  
Constant Load ◽  
Combustion Stability ◽  
Performance And Emission ◽  
Energy Share ◽  
The Stability

The main objective of this study was assessment of the performance, emissions and combustion characteristics of a diesel engine using RME–1-butanol blends. In assessing the combustion process, great importance was placed on evaluating the stability of this process. Not only were the typical COVIMEP indicators assessed, but also the non-burnability of the characteristic combustion stages: ignition delay, time of 50% heat release and the end of combustion. The evaluation of the combustion process based on the analysis of heat release. The tests carried out on a 1-cylinder diesel engine operating at a constant load. Research and evaluation of the combustion process of a mixture of RME and 1-butanol carried out for the entire range of shares of both fuels up to 90% of 1-butanol energetic fraction. The participation of butanol in combustion process with RME increased the in-cylinder peak pressure and the heat release rate. With the increase in the share of butanol there was noted a decrease in specific energy consumption and an increase in engine efficiency. The share of butanol improved the combustion stability. There was also an increase in NOx emissions and decrease in CO and soot emissions. The engine can be power by blend up to 80% energy share of butanol.

Spray and Combustion Characteristics of Biodiesel∕Diesel Blended Fuel in a Direct Injection Common-Rail Diesel Engine

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Hyun Kyu Suh ◽  
Hyun Gu Roh ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Injection Rate ◽  
Combustion Characteristics ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Pilot Injection ◽  
Blended Fuel ◽  
Conventional Diesel Fuel

The aim of this work is to investigate the effect of the blending ratio and pilot injection on the spray and combustion characteristics of biodiesel fuel and compare these factors with those of diesel fuel in a direct injection common-rail diesel engine. In order to study the factors influencing the spray and combustion characteristics of biodiesel fuel, experiments involving exhaust emissions and engine performance were conducted at various biodiesel blending ratios and injection conditions for engine operating conditions. The macroscopic and microscopic spray characteristics of biodiesel fuel, such as injection rate, split injection effect, spray tip penetration, droplet diameter, and axial velocity distribution, were compared with the results from conventional diesel fuel. For biodiesel blended fuel, it was revealed that a higher injection pressure is needed to achieve the same injection rate at a higher blending ratio. The spray tip penetration of biodiesel fuel was similar to that of diesel. The atomization characteristics of biodiesel show that it has higher Sauter mean diameter and lower spray velocity than conventional diesel fuel due to high viscosity and surface tension. The peak combustion pressures of diesel and blending fuel increased with advanced injection timing and the combustion pressure of biodiesel fuel is higher than that of diesel fuel. As the pilot injection timing is retarded to 15deg of BTDC that is closed by the top dead center, the dissimilarities of diesel and blending fuels combustion pressure are reduced. It was found that the pilot injection enhanced the deteriorated spray and combustion characteristics of biodiesel fuel caused by different physical properties of the fuel.

scholarly journals On the possibility to decrease the fuel consumption for a heavy-duty truck Diesel engine using the Turbo-compound method: a case study

2019 ◽  
Vol 290 ◽  
pp. 06008
Author(s):  
Bogdan Radu ◽  
Alexandru Racovitza
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Internal Combustion Engines ◽  
Direct Injection ◽  
Large Data ◽  
Gas Emissions ◽  
Main Research ◽  
Injection Methods ◽  
Calculation System ◽  
Release Characteristic

The reduction of Diesel internal combustion engines emissions is one of the major concerns of the engines manufacturers. Despite the fact that the efficiency of the gas post-treatment systems has been significantly improved, decreasing the smoke and the soot from the cylinder inside remains a main research goal. This work is proposing a theoretical study on these pollutants formation for different kinds of direct injection methods. By dividing the in-cylinder injection the heat release characteristic could be modified, leading to different temperature and pressure levels. Using exhaust gas recirculation (EGR) the reduction of the gas temperatures might also be decreased, limiting NOx formation. To evaluate the level of the cylinder gas emissions formation a two-step procedure could be followed. First, by using a numerical calculation system the heat release characteristic can be highlighted concerning a Diesel engine with stratified injection; then, using an experimental relationship applying a large data base, the amount of the gas emissions can be subsequently provided. The authors propose some combinations between injection characteristics and EGR used fractions which could generate successfully results speaking in terms of NOx, soot and smoke formation.

Assessment of a Syngas-Diesel Dual Fuelled Compression Ignition Engine

2010 ◽  
Author(s):  
Bibhuti B. Sahoo ◽  
Niranjan Sahoo ◽  
Ujjwal K. Saha
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Gas Flow ◽  
Direct Injection ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Exhaust Gas Temperature

Synthesis gas (Syngas), a mixture of hydrogen and carbon monoxide, can be manufactured from natural gas, coal, petroleum, biomass, and even from organic wastes. It can substitute fossil diesel as an alternative gaseous fuel in compression ignition engines under dual fuel operation route. Experiments were conducted in a single cylinder, constant speed and direct injection diesel engine fuelled with syngas-diesel in dual fuel mode. The engine is designed to develop a power output of 5.2 kW at its rated speed of 1500 rpm under variable loads with inducted syngas fuel having H2 to CO ratio of 1:1 by volume. Diesel fuel as a pilot was injected into the engine in the conventional manner. The diesel engine was run at varying loads of 20, 40, 60, 80 and 100%. The performance of dual fuel engine is assessed by parameters such as thermal efficiency, exhaust gas temperature, diesel replacement rate, gas flow rate, peak cylinder pressure, exhaust O2 and emissions like NOx, CO and HC. Dual fuel operation showed a decrease in brake thermal efficiency from 16.1% to a maximum of 20.92% at 80% load. The maximum diesel substitution by syngas was found 58.77% at minimum exhaust O2 availability condition of 80% engine load. The NOx level was reduced from 144 ppm to 103 ppm for syngas-diesel mode at the best efficiency point. Due to poor combustion efficiency of dual fuel operation, there were increases in CO and HC emissions throughout the range of engine test loads. The decrease in peak pressure causes the exhaust gas temperature to rise at all loads of dual fuel operation. The present investigation provides some useful indications of using syngas fuel in a diesel engine under dual fuel operation.

scholarly journals Experimental study of multiple pilot injection strategy in an automotive direct injection diesel engine

2018 ◽  
Vol 234 ◽  
pp. 03007
Author(s):  
Plamen Punov ◽  
Tsvetomir Gechev ◽  
Svetoslav Mihalkov ◽  
Pierre Podevin ◽  
Dalibor Barta
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Diesel Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection Timing ◽  
Pilot Injection ◽  
Injection Strategy ◽  
Direct Injection Diesel Engine ◽  
Rate Of Heat Release

The pilot injection strategy is a widely used approach for reducing the noise of the combustion process in direct injection diesel engines. In the last generation of automotive diesel engines up to several pilot injections could occur to better control the rate of heat release (ROHR) in the cylinder as well as the pollutant formation. However, determination of the timing and duration for each pilot injection needs to be precisely optimised. In this paper an experimental study of the pilot injection strategy was conducted on a direct injection diesel engine. Single and double pilot injection strategy was studied. The engine rated power is 100 kW at 4000 rpm while the rated torque is 320 Nm at 2000 rpm. An engine operating point determined by the rotation speed of 1400 rpm and torque of 100 Nm was chosen. The pilot and pre-injection timing was widely varied in order to study the influence on the combustion process as well as on the fuel consumption.

Sign in / Sign up

Export Citation Format

Share Document