Laminar Flame Speed and Ignition Delay Time Data for the Kinetic Modeling of Hydrogen and Syngas Fuel Blends

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Michael C. Krejci ◽  
Olivier Mathieu ◽  
Andrew J. Vissotski ◽  
Sankaranarayanan Ravi ◽  
Travis G. Sikes ◽  
...  
Keyword(s):  
Carbon Monoxide ◽  
Chemical Kinetics ◽  
Ignition Delay ◽  
Laminar Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Elevated Pressures ◽  
Ignition Delay Times ◽  
Wide Range ◽  
Delay Times

Laminar flame speeds and ignition delay times have been measured for hydrogen and various compositions of H2/CO (syngas) at elevated pressures and elevated temperatures. Two constant-volume cylindrical vessels were used to visualize the spherical growth of the flame through the use of a schlieren optical setup to measure the laminar flame speed of the mixture. Hydrogen experiments were performed at initial pressures up to 10 atm and initial temperatures up to 443 K. A syngas composition of 50/50 by volume was chosen to demonstrate the effect of carbon monoxide on H2-O2 chemical kinetics at standard temperature and pressures up to 10 atm. All atmospheric mixtures were diluted with standard air, while all elevated-pressure experiments were diluted with a He:O2 ratio of 7:1 to minimize instabilities. The laminar flame speed measurements of hydrogen and syngas are compared to available literature data over a wide range of equivalence ratios, where good agreement can be seen with several data sets. Additionally, an improved chemical kinetics model is shown for all conditions within the current study. The model and the data presented herein agree well, which demonstrates the continual, improved accuracy of the chemical kinetics model. A high-pressure shock tube was used to measure ignition delay times for several baseline compositions of syngas at three pressures across a wide range of temperatures. The compositions of syngas (H2/CO) by volume presented in this study included 80/20, 50/50, 40/60, 20/80, and 10/90, all of which are compared to previously published ignition delay times from a hydrogen-oxygen mixture to demonstrate the effect of carbon monoxide addition. Generally, an increase in carbon monoxide increases the ignition delay time, but there does seem to be a pressure dependency. At low temperatures and pressures higher than about 12 atm, the ignition delay times appear to be indistinguishable with an increase in carbon monoxide. However, at high temperatures the relative composition of H2 and CO has a strong influence on ignition delay times. Model agreement is good across the range of the study, particularly at the elevated pressures.

Laminar Flame Speed and Ignition Delay Time Data for the Kinetic Modeling of Hydrogen and Syngas Fuel Blends

2012 ◽  
Author(s):  
M. C. Krejci ◽  
O. Mathieu ◽  
A. J. Vissotski ◽  
S. Ravi ◽  
T. G. Sikes ◽  
...  
Keyword(s):  
Carbon Monoxide ◽  
Ignition Delay ◽  
Ignition Delay Time ◽  
Laminar Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Elevated Pressures ◽  
Ignition Delay Times ◽  
Wide Range ◽  
Delay Times

Laminar flame speeds and ignition delay times have been measured for hydrogen and various compositions of H2/CO (syngas) at elevated pressures and elevated temperatures. Two constant-volume cylindrical vessels were used to visualize the spherical growth of the flame through the use of a schlieren optical setup to measure the laminar flame speed of the mixture. Hydrogen experiments were performed at initial pressures up to 10 atm and initial temperatures up to 443 K. A syngas composition of 50/50 by volume was chosen to demonstrate the effect of carbon monoxide on H2−O2 chemical kinetics at standard temperature and pressures up to 10 atm. All atmospheric mixtures were diluted with standard air, while all elevated-pressure experiments were diluted with a He:O2 of 7:1 to minimize instabilities. The laminar flame speed measurements of hydrogen and syngas are compared to available literature data over a wide range of equivalence ratios where good agreement can be seen with several data sets. Additionally, an improved chemical kinetics model is shown for all conditions within the current study. The model and the data presented herein agree well, which demonstrates the continual, improved accuracy of the chemical kinetic model. A high-pressure shock tube was used to measure ignition delay times for several baseline compositions of syngas at three pressures across a wide range of temperatures. The compositions of syngas (H2/CO) by volume presented in this study included 80/20, 50/50, 40/60, 20/80, and 10/90, all of which are compared to previously published ignition delay times from a hydrogen-oxygen mixture to demonstrate the effect of carbon monoxide addition. Generally, an increase in carbon monoxide increases the ignition delay time, but there does seem to be a pressure dependency. At low temperatures and pressures higher than about 12 atm, the ignition delay times appear to be indistinguishable with an increase in carbon monoxide. However, at high temperatures the relative composition of H2 and CO has a strong influence on ignition delay times. Model agreement is good across the range of the study, particularly at the elevated pressures. Also, an increase in carbon monoxide causes the activation energy of the mixture to decrease.

Ignition and Flame Speed Kinetics of Two Natural Gas Blends With High Levels of Heavier Hydrocarbons

2008 ◽  
Author(s):  
Gilles Bourque ◽  
Darren Healy ◽  
Henry Curran ◽  
Christopher Zinner ◽  
Danielle Kalitan ◽  
...  
Keyword(s):  
High Pressure ◽  
Chemical Kinetics ◽  
Ignition Delay ◽  
Laminar Flame ◽  
Flame Speed ◽  
Data Set ◽  
Chemical Kinetic Model ◽  
Fuel Blends ◽  
Ignition Delay Times ◽  
Delay Times

High-pressure experiments and chemical kinetics modeling were performed to generate a database and a chemical kinetic model that can characterize the combustion chemistry of methane-based fuel blends containing significant levels of heavy hydrocarbons (up to 37.5% by volume). Ignition delay times were measured in two different shock tubes and in a rapid compression machine at pressures up to 34 atm and temperatures from 740 to 1660 K. Laminar flame speeds were also measured at pressures up to 4 atm using a high-pressure vessel with optical access. Two different fuel blends containing ethane, propane, n-butane, and n-pentane added to methane were studied at equivalence ratios varying from lean (0.3) to rich (2.0). This paper represents the most comprehensive set of experimental ignition and laminar flame speed data available in the open literature for CH4/C2H6/C3H8/C4H10/C5H12 fuel blends with significant levels of C2+ hydrocarbons. Using these data, a detailed chemical kinetics model, based on current and recent work by the authors, was compiled and refined. The predictions of the model are very good over the entire range of ignition delay times, considering the fact that the data set is so thorough. Nonetheless, some improvements to the model can still be made with respect to ignition times at the lowest temperatures and for the laminar flame speeds at pressures above 1 atm and rich conditions.

Numerical Study on the Effect of Real Syngas Compositions on Ignition Delay Times and Laminar Flame Speeds at Gas Turbine Conditions

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
Olivier Mathieu ◽  
Eric L. Petersen ◽  
Alexander Heufer ◽  
Nicola Donohoe ◽  
Wayne Metcalfe ◽  
...  
Keyword(s):  
Ignition Delay ◽  
Delay Time ◽  
Gas Turbines ◽  
Ignition Delay Time ◽  
Laminar Flame ◽  
Flame Speed ◽  
Operating Conditions ◽  
Laminar Flame Speed ◽  
Ignition Delay Times ◽  
Delay Times

Depending on the feedstock and the production method, the composition of syngas can include (in addition to H2 and CO) small hydrocarbons, diluents (CO2, water, and N2), and impurities (H2S, NH3, NOx, etc.). Despite this fact, most of the studies on syngas combustion do not include hydrocarbons or impurities and in some cases not even diluents in the fuel mixture composition. Hence, studies with realistic syngas composition are necessary to help in designing gas turbines. The aim of this work was to investigate numerically the effect of the variation in the syngas composition on some fundamental combustion properties of premixed systems such as laminar flame speed and ignition delay time at realistic engine operating conditions. Several pressures, temperatures, and equivalence ratios were investigated for the ignition delay times, namely 1, 10, and 35 atm, 900–1400 K, and ϕ = 0.5 and 1.0. For laminar flame speed, temperatures of 300 and 500 K were studied at pressures of 1 atm and 15 atm. Results showed that the addition of hydrocarbons generally reduces the reactivity of the mixture (longer ignition delay time, slower flame speed) due to chemical kinetic effects. The amplitude of this effect is, however, dependent on the nature and concentration of the hydrocarbon as well as the initial condition (pressure, temperature, and equivalence ratio).

Ignition and Flame Speed Kinetics of Two Natural Gas Blends With High Levels of Heavier Hydrocarbons

2009 ◽  
Vol 132 (2) ◽  
Author(s):  
Gilles Bourque ◽  
Darren Healy ◽  
Henry Curran ◽  
Christopher Zinner ◽  
Danielle Kalitan ◽  
...  
Keyword(s):  
High Pressure ◽  
Chemical Kinetics ◽  
Ignition Delay ◽  
Laminar Flame ◽  
Flame Speed ◽  
Data Set ◽  
Chemical Kinetic Model ◽  
Fuel Blends ◽  
Ignition Delay Times ◽  
Delay Times

High-pressure experiments and chemical kinetics modeling were performed to generate a database and a chemical kinetic model that can characterize the combustion chemistry of methane-based fuel blends containing significant levels of heavy hydrocarbons (up to 37.5% by volume). Ignition delay times were measured in two different shock tubes and in a rapid compression machine at pressures up to 34 atm and temperatures from 740 K to 1660 K. Laminar flame speeds were also measured at pressures up to 4 atm using a high-pressure vessel with optical access. Two different fuel blends containing ethane, propane, n-butane, and n-pentane added to methane were studied at equivalence ratios varying from lean (0.3) to rich (2.0). This paper represents the most comprehensive set of experimental ignition and laminar flame speed data available in the open literature for CH4/C2H6/C3H8/C4H10/C5H12 fuel blends with significant levels of C2+ hydrocarbons. Using these data, a detailed chemical kinetics model based on current and recent work by the authors was compiled and refined. The predictions of the model are very good over the entire range of ignition delay times, considering the fact that the data set is so thorough. Nonetheless, some improvements to the model can still be made with respect to ignition times at the lowest temperatures and for the laminar flame speeds at pressures above 1 atm and at rich conditions.

Ignition Delay Time and Laminar Flame Speed Calculations for Natural Gas/Hydrogen Blends at Elevated Pressures

2012 ◽  
Author(s):  
Marissa Brower ◽  
Eric Petersen ◽  
Wayne Metcalfe ◽  
Henry J. Curran ◽  
Marc Füri ◽  
...  
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Chemical Kinetics ◽  
Ignition Delay ◽  
Ignition Delay Time ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Hydrogen Addition

Applications of natural gas and hydrogen co-firing have received increased attention in the gas turbine market, which aims at higher flexibility due to concerns over the availability of fuels. While much work has been done in the development of a fuels database and corresponding chemical kinetics mechanism for natural gas mixtures, there are nonetheless few if any data for mixtures with high levels of hydrogen at conditions of interest to gas turbines. The focus of the present paper is on gas turbine engines with primary and secondary reaction zones as represented in the Alstom and Rolls Royce product portfolio. The present effort includes a parametric study, a gas turbine model study, and turbulent flame speed predictions. Using a highly optimized chemical kinetics mechanism, ignition delay times and laminar burning velocities were calculated for fuels from pure methane to pure hydrogen and with natural gas/hydrogen mixtures. A wide range of engine-relevant conditions were studied: pressures from 1 to 30 atm, flame temperatures from 1600 to 2200 K, primary combustor inlet temperature from 300 to 900 K, and secondary combustor inlet temperatures from 900 to 1400 K. Hydrogen addition was found to increase the reactivity of hydrocarbon fuels at all conditions by increasing the laminar flame speed and decreasing the ignition delay time. Predictions of turbulent flame speeds from the laminar flame speeds show that hydrogen addition affects the reactivity more when turbulence is considered. This combined effort of industrial and university partners brings together the know-how of applied, as well as experimental and theoretical disciplines.

Ignition delay times, laminar flame speeds, and mechanism validation for natural gas/hydrogen blends at elevated pressures

2014 ◽  
Vol 161 (6) ◽  
pp. 1432-1443 ◽  
Author(s):  
Nicola Donohoe ◽  
Alexander Heufer ◽  
Wayne K. Metcalfe ◽  
Henry J. Curran ◽  
Marissa L. Davis ◽  
...  
Keyword(s):  
Natural Gas ◽  
Ignition Delay ◽  
Laminar Flame ◽  
Elevated Pressures ◽  
Ignition Delay Times ◽  
Delay Times

scholarly journals Comparative Study on Chemical Kinetics Mechanisms for Methane-Based Fuel Mixtures under Engine-Relevant Conditions

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2834
Author(s):  
Amin Paykani
Keyword(s):  
Experimental Data ◽  
Natural Gas ◽  
Chemical Kinetics ◽  
Ignition Delay ◽  
High Pressures ◽  
Laminar Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Si Engine ◽  
Fuel Blends

The use of natural gas in pure or in a blended form with hydrogen and syngas in spark ignition (SI) engines has received much attention in recent years. They have higher diffusion coefficient and laminar flame speed, a small quenching distance and wider flammability limit which compensate the demerits of the lean-burn natural gas combustion. Therefore, a careful examination of the chemical kinetics of combustion of gaseous fuel blends is of great importance. In this paper, performance of the various chemical kinetics mechanisms is compared against experimental data, accumulated for methane-based fuel blends under engine-relevant conditions to find the most appropriate mechanism in engine simulations. Pure methane, methane/syngas, and methane/propane blends are mainly studied at various temperatures, pressures, and equivalence ratios. The ignition delay time and laminar flame speed are used as quantitative metrics to compare the simulation results with the data from experiments. The mechanisms were shown to be mainly consistent with the experimental data of lean and stoichiometric mixtures at high pressures. It was also shown that the GRI-3.0 and 290Rxn mechanisms have high compatibility with the ignition delay times and laminar flame speed at high pressures and lean conditions, and they can be utilized for simulations of SI engine combustion due to their lower computational cost. The results of present research provide an important contribution to the methane-based fuel blends combustion simulation under SI engine-relevant conditions.

scholarly journals Investigation of the Effect of Hydrogen and Methane on Combustion of Multicomponent Syngas Mixtures using a Constructed Reduced Chemical Kinetics Mechanism

Energies ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 2442 ◽  
Author(s):  
Nearchos Stylianidis ◽  
Ulugbek Azimov ◽  
Martin Birkett
Keyword(s):  
Chemical Kinetics ◽  
Ignition Delay ◽  
Delay Time ◽  
Ignition Delay Time ◽  
High Pressures ◽  
Laminar Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
The Difference ◽  
Rich Mixtures

This study investigated the effects of H2 and CH4 concentrations on the ignition delay time and laminar flame speed during the combustion of CH4/H2 and multicomponent syngas mixtures using a novel constructed reduced syngas chemical kinetics mechanism. The results were compared with experiments and GRI Mech 3.0 mechanism. It was found that mixture reactivity decreases and increases when higher concentrations of CH4 and H2 were used, respectively. With higher H2 concentration in the mixture, the formation of OH is faster, leading to higher laminar flame speed and shorter ignition delay time. CH4 and H2 concentrations were calculated at different pressures and equivalence ratios, showing that at high pressures CH4 is consumed slower, and, at different equivalence ratios CH4 reacts at different temperatures. In the presence of H2, CH4 was consumed faster. In the conducted two-stage sensitivity analysis, the first analysis showed that H2/CH4/CO mixture combustion is driven by H2-based reactions related to the consumption/formation of OH and CH4 recombination reactions are responsible for CH4 oxidation. The second analysis showed that similar CH4-based and H2 -based reactions were sensitive in both, methane- and hydrogen-rich H2/CH4 mixtures. The difference was observed for reactions CH2O + OH = HCO + H2O and CH4 + HO2 = CH3 + H2O2, which were found to be important for CH4-rich mixtures, while reactions OH + HO2 = H2O + O2 and HO2 + H = OH + OH were found to be important for H2-rich mixtures.

Laminar Flame Speed Measurements and Modeling of Alkane Blends at Elevated Pressures With Various Diluents

2011 ◽  
Author(s):  
Yash Kochar ◽  
Jerry Seitzman ◽  
Timothy Lieuwen ◽  
Wayne Metcalfe ◽  
Sine´ad Burke ◽  
...  
Keyword(s):  
Chemical Kinetics ◽  
Laminar Flame ◽  
Initial Pressure ◽  
Elevated Pressure ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Fuel Blends ◽  
Elevated Pressures ◽  
Flame Method ◽  
The Stability

Laminar flame speeds at elevated pressure for methane-based fuel blends are important for refining the chemical kinetics that are relevant at engine conditions. The present paper builds on earlier measurements and modeling by the authors by extending the validity of a chemical kinetics mechanism to laminar flame speed measurements obtained in mixtures containing significant levels of helium. Such mixtures increase the stability of the experimental flames at elevated pressures and extend the range of laminar flame speeds. Two experimental techniques were utilized, namely a Bunsen burner method and an expanding spherical flame method. Pressures up to 10 atm were studied, and the mixtures ranged from pure methane to binary blends of CH4/C2H6 and CH4/C3H8. In the Bunsen flames, the data include elevated initial temperatures up to 650 K. There is generally good agreement between model and experiment, although some discrepancies still exist with respect to equivalence ratio for certain cases. A significant result of the present study is that the effect of mixture composition on flame speed is well captured by the mechanism over the extreme ranges of initial pressure and temperature covered herein. Similarly, the mechanism does an excellent job at modeling the effect of initial temperature for methane-based mixtures up to at least 650 K.

The Effect of Impurities on Ignition Delay Times and Laminar Flame Speeds of Syngas Mixtures at Gas Turbine Conditions

2014 ◽  
Author(s):  
Olivier Mathieu ◽  
Joshua W. Hargis ◽  
Eric L. Petersen ◽  
John Bugler ◽  
Henry J. Curran ◽  
...  
Keyword(s):  
Ignition Delay ◽  
Delay Time ◽  
Gas Turbines ◽  
Ignition Delay Time ◽  
Laminar Flame ◽  
Flame Speed ◽  
Operating Conditions ◽  
Laminar Flame Speed ◽  
Ignition Delay Times ◽  
Combustion Properties

In addition to mostly H2 and CO, syngas also contains reasonable amounts of light hydrocarbons, CO2, H2O, N2, and Ar. Impurities such as NH3, HCN, COS, H2S, and NOx (NO, NO2, N2O) are also commonly found in syngas. The presence of these impurities, even in very low concentrations, can induce some large changes in combustion properties. Although they introduce potential design and operational issues for gas turbines, these changes in combustion properties due to the presence of impurities are still not well characterized. The aim of this work was therefore to investigate numerically the effect of the presence of impurities in realistic syngas compositions on some fundamental combustion properties of premixed systems such as laminar flame speed and ignition delay time, at realistic engine operating conditions. To perform this study, a state-of-the-art C0–C3 detailed kinetics mechanism was used. This mechanism was combined with recent, optimized sub-mechanisms for impurities which can impact the combustion properties of the syngas such as nitrogenous species (i.e., N2O, NO2, NH3, and HCN) and sulfur-based species such as H2S, SO2 and COS. Several temperatures, pressures, and equivalence ratios were investigated. The results of this study showed that the addition of some impurities modifies notably the reactivity of the mixture. The ignition delay time is decreased by the addition of NO2 and H2S at the temperatures and pressures for which the HO2 radical dominates the H2 combustion. However, while NO2 has no effect when OH is dominating, H2S increases the ignition delay time in such conditions for pressures above 1 atm. The amplitude of these effects is however dependent on the impurity concentration. Laminar flame speeds are not sensitive to NO2 addition but they are to NH3 and HCN, inducing a small reduction of the laminar flame speed at fuel rich conditions. H2S exhibits some inhibiting effects on the laminar flame speed but only for high concentrations. The inhibiting effects of NH3, HCN, and H2S are due to the OH radical consumption by these impurities, leading to the formation of radicals that are less reactive.

Sign in / Sign up

Export Citation Format

Share Document