Measurement of Flame Frequency Response Functions Under Exhaust Gas Recirculation Conditions

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
Joseph Ranalli ◽  
Don Ferguson
Keyword(s):  
Transfer Function ◽  
Carbon Capture ◽  
Transfer Functions ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Exhaust Gas ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Flame Response ◽  
Gas Recirculation

Exhaust gas recirculation has been proposed as a potential strategy for reducing the cost and efficiency penalty associated with postcombustion carbon capture. However, this approach may cause as-yet unresolved effects on the combustion process, including additional potential for the occurrence of thermoacoustic instabilities. Flame dynamics, characterized by the flame transfer function, were measured in traditional swirl stabilized and low-swirl injector combustor configurations, subject to exhaust gas circulation simulated by N2 and CO2 dilution. The flame transfer functions exhibited behavior consistent with a low-pass filter and showed phase dominated by delay. Flame transfer function frequencies were nondimensionalized using Strouhal number to highlight the convective nature of this delay. Dilution was observed to influence the dynamics primarily through its role in changing the size of the flame, indicating that it plays a similar role in determining the dynamics as changes in the equivalence ratio. Notchlike features in the flame transfer function were shown to be related to interference behaviors associated with the convective nature of the flame response. Some similarities between the two stabilization configurations proved limiting and generalization of the physical behaviors will require additional investigation.

scholarly journals Learning reference governor for cycle-to-cycle combustion control with misfire avoidance in spark-ignition engines at high exhaust gas recirculation–diluted conditions

2020 ◽  
Vol 21 (10) ◽  
pp. 1819-1834
Author(s):  
Bryan P Maldonado ◽  
Nan Li ◽  
Ilya Kolmanovsky ◽  
Anna G Stefanopoulou
Keyword(s):  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Intake Manifold ◽  
Exhaust Gas ◽  
Model Free ◽  
Recirculation Rate ◽  
Valve Position ◽  
Gas Recirculation ◽  
Reference Governor

Cycle-to-cycle feedback control is employed to achieve optimal combustion phasing while maintaining high levels of exhaust gas recirculation by adjusting the spark advance and the exhaust gas recirculation valve position. The control development is based on a control-oriented model that captures the effects of throttle position, exhaust gas recirculation valve position, and spark timing on the combustion phasing. Under the assumption that in-cylinder pressure information is available, an adaptive extended Kalman filter approach is used to estimate the exhaust gas recirculation rate into the intake manifold based on combustion phasing measurements. The estimation algorithm is adaptive since the cycle-to-cycle combustion variability (output covariance) is not known a priori and changes with operating conditions. A linear quadratic regulator controller is designed to maintain optimal combustion phasing while maximizing exhaust gas recirculation levels during load transients coming from throttle tip-in and tip-out commands from the driver. During throttle tip-outs, however, a combination of a high exhaust gas recirculation rate and an overly advanced spark, product of the dynamic response of the system, generates a sequence of misfire events. In this work, an explicit reference governor is used as an add-on scheme to the closed-loop system in order to avoid the violation of the misfire limit. The reference governor is enhanced with model-free learning which enables it to avoid misfires after a learning phase. Experimental results are reported which illustrate the potential of the proposed control strategy for achieving an optimal combustion process during highly diluted conditions for improving fuel efficiency.

The impact of water injection and exhaust gas recirculation on combustion and emissions in a heavy-duty compression ignition engine operated on diesel and gasoline

2019 ◽  
Vol 21 (8) ◽  
pp. 1555-1573 ◽  
Author(s):  
Michael Pamminger ◽  
Buyu Wang ◽  
Carrie M Hall ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
Thermal Efficiency ◽  
Water Injection ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Exhaust Gas ◽  
Brake Thermal Efficiency ◽  
Fuel Ratio ◽  
Main Injection ◽  
Gas Recirculation ◽  
Diesel Operation

Steady-state experiments were conducted on a 12.4L, six-cylinder heavy-duty engine to investigate the influence of port-injected water and dilution via exhaust gas recirculation (EGR) on combustion and emissions for diesel and gasoline operation. Adding a diluent to the combustion process reduces peak combustion temperatures and can reduce the reactivity of the charge, thereby increasing the ignition-delay and, allowing for more time to premix air and fuel. Experiments spanned water/fuel mass ratios up to 140mass% and exhaust gas recirculation ratios up to 20vol% for gasoline and diesel operation with different injection strategies. Diluting the combustion process with either water or EGR resulted in a significant reduction in nitrogen oxide emissions along with a reduction in brake thermal efficiency. The sensitivity of brake thermal efficiency to water and EGR varied among the fuels and injection strategies investigated. An efficiency breakdown revealed that water injection considerably reduced the wall heat transfer; however, a substantial increase in exhaust enthalpy offset the reduction in wall heat transfer and led to a reduction in brake thermal efficiency. Regular diesel operation with main and post injection exhibited a brake thermal efficiency of 45.8% and a 0.3% reduction at a water/fuel ratio of 120%. The engine operation with gasoline, early pilot, and main injection strategy showed a brake thermal efficiency of 45.0% at 0% water/fuel ratio, and a 1.2% decrease in brake thermal efficiency for a water/fuel ratio of 140%. Using EGR as a diluent reduced the brake thermal efficiency by 0.3% for diesel operation, comparing ratios of 0% and 20% EGR. However, a higher impact on brake thermal efficiency was seen for gasoline operation with early pilot and main injection strategy, with a reduction of about 0.8% comparing 0% and 20% EGR. Dilution by means of EGR exhibited a reduction in nitrogen oxide emissions up to 15 g/kWh; water injection showed only up to 10 g/kWh reduction for the EGR rates and water/fuel ratio investigated.

Diesel Engine Intake Condition Control-Oriented Models for Active Fuel Injection Profile Control

2011 ◽  
Author(s):  
Fengjun Yan ◽  
Junmin Wang
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
High Fidelity ◽  
Exhaust Gas ◽  
Engine Model ◽  
Profile Control ◽  
Gas Recirculation

Fueling control in Diesel engines is not only of significance to the combustion process in one particular cycle, but also influences the subsequent dynamics of air-path loop and combustion events, particularly when exhaust gas recirculation (EGR) is employed. To better reveal such inherently interactive relations, this paper presents a physics-based, control-oriented model describing the dynamics of the intake conditions with fuel injection profile being its input for Diesel engines equipped with EGR and turbocharging systems. The effectiveness of this model is validated by comparing the predictive results with those produced by a high-fidelity 1-D computational GT-Power engine model.

Exhaust Gas Recirculation Performance in Dry Low Emissions Combustors

2011 ◽  
Author(s):  
A. M. Elkady ◽  
A. R. Brand ◽  
C. L. Vandervort ◽  
A. T. Evulet
Keyword(s):  
Gas Turbine ◽  
Co2 Capture ◽  
Carbon Capture ◽  
Power Plants ◽  
Nox Reduction ◽  
Co2 Concentration ◽  
Exhaust Gas Recirculation ◽  
Exhaust Gas ◽  
Low Oxygen ◽  
Gas Recirculation

In a carbon constrained world there is a need for capturing and sequestering CO2. Post-combustion carbon capture via Exhaust Gas Recirculation (EGR) is considered a feasible means of reducing emission of CO2 from power plants. Exhaust Gas Recirculation is an enabling technology for increasing the CO2 concentration within the gas turbine cycle and allow the decrease of the size of the separation plant, which in turn will enable a significant reduction in CO2 capture cost. This paper describes the experimental work performed to better understand the risks of utilizing EGR in combustors employing dry low emissions (DLE) technologies. A rig was built for exploring the capability of premixers to operate in low O2 environment, and a series of experiments in a visually accessible test rig was performed at representative aeroderivative gas turbine pressures and temperatures. Experimental results include the effect of applying EGR on operability, efficiency and emissions performance under conditions of up to 40% EGR. Findings confirm the viability of EGR for enhanced CO2 capture; In addition, we confirm benefits of NOx reduction while complying with CO emissions in DLE combustors under low oxygen content oxidizer.

Enhancement of the combustion process in dual-fuel engines at part loads using exhaust gas recirculation

2007 ◽  
Vol 221 (7) ◽  
pp. 877-888 ◽  
Author(s):  
V Pirouzpanah ◽  
R Khoshbakhti Saray
Keyword(s):  
Chemical Kinetics ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Combustion Model ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Performance And Emission ◽  
Dual Fuel Engines ◽  
Gas Recirculation

Dual-fuel engines at part loads inevitably suffer from lower thermal efficiency and higher carbon monoxide and unburned fuel emission. The present work was carried out to investigate the combustion characteristics of a dual-fuel (diesel-gas) engine at part loads, using a single-zone combustion model with detailed chemical kinetics for combustion of natural gas fuel. The authors have developed software in which the pilot fuel is considered as a subsidiary zone and a heat source derived from two superimposedWiebe combustion functions to account for its contribution to ignition of the gaseous fuel and the rest of the total released energy. The chemical kinetics mechanism consists of 112 reactions with 34 species. This quasi-two-zone combustion model is able to establish the development of the combustion process with time and the associated important operating parameters, such as pressure, temperature, heat release rate (HRR), and species concentration. Therefore, this paper describes an attempt to investigate the combustion phenomenon at part loads and using hot exhaust gas recirculation (EGR) to improve the above-mentioned drawbacks and problems. By employing this technique, it is found that lower percentages of EGR and allowance for its thermal and radical effects have a positive influence on performance and emission parameters of dual-fuel engines at part loads. Predicted values show good agreement with corresponding experimental values under special engine operating conditions (quarter-load, 1400 r/min). Implications are discussed in detail.

Study of Using Exhaust Gas Recirculation on a Gas Turbine for Carbon Capture

2020 ◽  
Author(s):  
Dan Burnes ◽  
Priyank Saxena ◽  
Paul Dunn
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Carbon Capture ◽  
Hydrocarbon Fuel ◽  
Exhaust Gas Recirculation ◽  
Exhaust Gas ◽  
Hybrid Solutions ◽  
Industrial Gas Turbines ◽  
Industrial Gas Turbine ◽  
Gas Recirculation

Abstract The growing call of minimizing carbon dioxide and other greenhouse gases emitting from energy and transportation products will spur innovation to meet new stringent requirements while striving to preserve significant investments in the current infrastructure. This paper presents quantitative analysis of exhaust gas recirculation (EGR) on industrial gas turbines to enable carbon sequestration venturing towards emission free operation. This study will show the effect of using EGR on gas turbine performance and operation, combustion characteristics, and demonstrate potential hybrid solutions with detailed constituent accounting. Both single shaft and two shaft gas turbines for power generation and mechanically driven equipment are considered for application of this technology. One key element is assessing the combustion system operating at reduced O2 levels within the industrial gas turbine. With the gas turbine behavior operating with EGR defined at a reasonable operating state, a parametric study shows rates of CO2 sequestration along with quantifying supplemental O2 required at the inlet, if needed, to sustain combustion. With rates of capture known, a further exploration is examined reviewing potential utilities, monetizing these sequestered constituents. Ultimately, the objective is to preview a potential future of operating industrial gas turbines in a non-emissive and in some cases carbon negative manner while still using hydrocarbon fuel.

Modeling and control of fuel distribution in a dual-fuel internal combustion engine leveraging late intake valve closings

2016 ◽  
Vol 18 (8) ◽  
pp. 797-809 ◽  
Author(s):  
Mateos Kassa ◽  
Carrie Hall ◽  
Andrew Ickes ◽  
Thomas Wallner
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Internal Combustion ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Intake Valve ◽  
Fuel Distribution ◽  
Gas Recirculation

In internal combustion engines, cycle-to-cycle and cylinder-to-cylinder variations of the combustion process have been shown to negatively impact the fuel efficiency of the engine and lead to higher exhaust emissions. The combustion variations are generally tied to differences in the composition and condition of the trapped mass throughout each cycle and across individual cylinders. Thus, advanced engines featuring exhaust gas recirculation, flexible valve actuation systems, advanced fueling strategies, and turbocharging systems are prone to exhibit higher variations in the combustion process. In this study, the cylinder-to-cylinder variations of the combustion process in a dual-fuel internal combustion engine leveraging late intake valve closing are investigated and a model to predict and address one of the root causes for these variations across cylinders is developed. The study is conducted on an inline six-cylinder heavy-duty dual-fuel engine equipped with exhaust gas recirculation, a variable geometry turbocharger, and a fully flexible variable intake valve actuation system. The engine is operated with late intake valve closure timings in a dual-fuel combustion mode in which a high reactivity fuel is directly injected into the cylinders and a low reactivity fuel is port injected into the cylinders. The cylinder-to-cylinder variations observed in the study have been associated with the maldistribution of the port-injected fuel, which is exacerbated at late intake valve timings. The resulting difference in indicated mean effective pressure between the cylinders ranges from 9% at an intake valve closing of 570° after top dead center to 38% at an intake valve closing of 620° after top dead center and indicates an increasingly uneven fuel distribution. The study leverages both experimental and simulation studies to investigate the distribution of the port-injected fuel and its impact on cylinder-to-cylinder variation. The effects of intake valve closing as well as the impact of intake runner length on fuel distribution were quantitatively analyzed, and a model was developed that can be used to accurately predict the fuel distribution of the port-injected fuel at different operating conditions with an average estimation error of 1.5% in cylinder-specific fuel flow. A model-based control strategy is implemented to adjust the fueling at each port and shown to significantly reduce the cylinder-to-cylinder variations in fuel distribution.

Transfer function analysis of autonomic regulation. I. Canine atrial rate response

1989 ◽  
Vol 256 (1) ◽  
pp. H142-H152 ◽  
Author(s):  
R. D. Berger ◽  
J. P. Saul ◽  
R. J. Cohen
Keyword(s):  
Transfer Function ◽  
Transfer Functions ◽  
Function Analysis ◽  
Cardiac Pacemaker ◽  
Corner Frequency ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Atrial Rate ◽  
Transfer Function Analysis ◽  
Functional Components

We present a useful technique for analyzing the various functional components that comprise the cardiovascular control network. Our approach entails the imposition of a signal with broad frequency content as an input excitation and the computation of a system transfer function using spectral estimation techniques. In this paper, we outline the analytical methods involved and demonstrate the utility of our approach in studying the dynamic behavior of the canine cardiac pacemaker. In particular, we applied frequency-modulated pulse trains to either the right vagus or the cardiac sympathetic nerve and computed transfer functions between nerve stimulation rate and the resulting atrial rate. We found that the sinoatrial node (and associated automatic tissue) responds as a low-pass filter to fluctuations in either sympathetic or parasympathetic tone. For sympathetic fluctuations, however, the filter has a much lower corner frequency than for vagal fluctuations and is coupled with a roughly 1.7-s pure delay. We further found that the filter characteristics, including the location of the corner frequency and rate of roll-off, depend significantly on the mean level of sympathetic or vagal tone imposed.

The effects of exhaust gas recirculation on diesel combustion and emissions

2000 ◽  
Vol 1 (1) ◽  
pp. 107-126 ◽  
Author(s):  
N Ladommatos ◽  
S Abdelhalim ◽  
H Zhao
Keyword(s):  
Carbon Dioxide ◽  
Heat Capacity ◽  
Diesel Engine ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Particulate Emissions ◽  
Exhaust Gas ◽  
Particulate Emission ◽  
Gas Recirculation ◽  
Charge Temperature

An investigation was conducted with the aim of identifying and quantifying the effects of exhaust gas recirculation (EGR) on diesel engine combustion and exhaust emissions. Five effects of EGR were identified and investigated experimentally: the reduction in oxygen supply to the engine, participation in the combustion process of carbon dioxide and water vapour present in the EGR, increase in the specific heat capacity of the engine inlet charge, increased inlet charge temperature and reduction in the inlet charge mass flowrate arising from the use of hot EGR. The experimental methodology developed allowed each one of these effects to be investigated and quantified separately. The investigation was carried out on a high-speed, direct injection diesel engine, running at an intermediate speed and load. A limited number of tests were also conducted in an optically accessible diesel engine, which established the effects of EGR on local flame temperature. Finally, tests were conducted with simulated EGR being used additionally to the engine air supply. This contrasts with the conventional use of EGR, whereby EGR replaces some of the air supplied to the engine. It was found that the first effect of EGR (reduction in the oxygen flowrate to the engine) was substantial and resulted in very large reductions in exhaust NOx at the expense of higher particulate emissions. The second and third effects (participation of carbon dioxide and water vapour in the combustion process and increase in the charge specific heat capacity) were almost insignificant. The fourth effect (higher inlet charge temperature) increased both exhaust NOx and particulate emissions. The fifth effect (reduction in the inlet charge due to thermal throttling) reduced NOx but raised particulate emission. Finally, when EGR was used additionally to the inlet air charge (rather than displacing air), substantial reductions in NOx were recorded with little increase in particulate emission.

The effects of carbon dioxide in exhaust gas recirculation on diesel engine emissions

1998 ◽  
Vol 212 (1) ◽  
pp. 25-42 ◽  
Author(s):  
N Ladommatos ◽  
S M Adelhalim ◽  
H Zhao ◽  
Z Hu
Keyword(s):  
Carbon Dioxide ◽  
Diesel Engine ◽  
High Speed ◽  
Combustion Process ◽  
Dilution Effect ◽  
Exhaust Gas Recirculation ◽  
Chemical Effect ◽  
Particulate Emissions ◽  
Exhaust Gas ◽  
Gas Recirculation

The investigation was conducted on a high-speed direct injection diesel engine and was concerned with the effects of exhaust gas recirculation (EGR) on diesel engine combustion and emissions. In particular, the effects of carbon dioxide (CO2), a principal constituent of EGR, on combustion and emissions were analysed and quantified experimentally. The use of CO2 to displace oxygen (O2) in the inlet air resulted in: reduction in the O2 supplied to the engine (dilution effect), increased inlet charge thermal capacity (thermal effect), and, potentially, participation of the CO2 in the combustion process (chemical effect). In a separate series of tests the temperature of the engine inlet charge was raised gradually in order to simulate the effect of mixing hot EGR with engine inlet air. Finally, tests were carried out during which the CO2 added to the engine air flow increased the charge mass flowrate to the engine, rather than displacing some of the O2 in the inlet air. It was found that when CO2 displaced O2 in the inlet charge, both the chemical and thermal effects on exhaust emissions were small. However, the dilution effect was substantial, and resulted in very large reductions in exhaust oxides of nitrogen (NO x) at the expense of higher particulate and unburned hydrocarbon (uHC) emissions. Higher inlet charge temperature increased exhaust NO x and particulate emissions, but reduced uHC emissions. Finally, when CO2 was additional to the inlet air charge (rather than displacing O2), large reductions in NOx were recorded with little increase in particulate emissions.

Sign in / Sign up

Export Citation Format

Share Document